Experimental Investigation of Concrete Beams Reinforced with Glass Fiber–Reinforced Polymer Bars
Publication: Journal of Composites for Construction
Volume 26, Issue 5
Abstract
Concrete beams reinforced in shear and flexure with linear elastic and brittle glass fiber–reinforced polymer (GFRP) bars show differences in behavior when compared with the traditional steel-reinforced concrete beams. The flexural design of these beams follows similar principles as the design of steel-reinforced concrete members, except that the cross section is over-reinforced to compensate for the lack of reinforcement ductility. GFRP-reinforced beams are designed in shear using semiempirical modifications to the design equations for steel-reinforced concrete. The modified equations have not been well studied for beams with high shear span to depth (a/d) ratios. The presented research program is composed of three-point bending tests of ten GFRP-reinforced concrete beams, with a/d slenderness ratios from 4.5 to 10.5 with constant flexural reinforcement and varied shear reinforcing. The observed mode of failure transitioned from shear to flexure-controlled with increasing specimen slenderness and increased shear reinforcing. All failures were controlled by concrete behavior, either in tension for beams without shear reinforcement or compression for beams with shear reinforcement. The inclusion of GFRP stirrups in the beams prevented brittle failures by providing confinement to concrete. Comparisons with the current design rules showed good agreement with experimental results. However, the relative contribution of concrete and reinforcement to shear-carrying capacities differed in the code predictions from results derived from measured strains.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors acknowledge the financial contribution of the Natural Sciences and Engineering Council of Canada (NSERC) and the Ministry of Transportation of Ontario (MTO) for their financial support of this research program. The authors also extend their thanks to Schoeck/Fiberline for their contributions of longitudinal reinforcement and to B&BFRP composites for the donation of stirrups.
Notation
The following symbols are used in this paper:
- a
- shear span, distance from support to point of load application;
- a/d
- ratio of shear span to the depth of longitudinal reinforcement;
- AR
- sectional area of longitudinal reinforcement;
- AV, AfV
- area of shear reinforcement within a single spacing;
- bw
- width of the concrete compressive zone (equivalent for rectangular sections);
- d
- depth from the extreme compression fiber to the centroid of the tensile longitudinal reinforcement;
- dv
- effective shear depth;
- ER, EF
- axial stiffness of longitudinal reinforcement;
- specified concrete compressive strength;
- ffu
- ultimate allowable stress in the transverse GFRP reinforcement;
- fy
- yield strength of steel;
- k
- ratio of depth of neutral axis to reinforcement depth;
- km
- modification factor for moment interaction;
- kr
- modification factor for the stiffness of longitudinal reinforcement;
- Mf
- factored applied moment;
- Mr
- flexural resistance of a member;
- s
- spacing of transverse reinforcement;
- Vc
- concrete contribution to the overall shear resistance of a beam;
- Vf
- factored applied shear;
- Vr
- shear resistance of a beam;
- VsF
- transverse FRP reinforcement contribution to the overall shear resistance of a beam;
- Vss
- transverse steel reinforcement contribution to the overall shear resistance of a beam;
- λ
- factor to account for the effect of concrete density of shear resistance;
- ϕc
- material resistance factor for concrete, taken as 1 for this research;
- ϕF
- material resistance factor for FRP, taken as 1 for this research;
- ρFw
- longitudinal reinforcement ratio; and
- θ
- angle of inclination of the principal compressive stress to the longitudinal axis of the member.
References
ACI (American Concrete Institute). 2004. Guide test methods for fiber–reinforced polymers (FRPs) for reinforcing or strengthening concrete structures. ACI 440.3R-04. Farmington Hills, MI: ACI.
ACI (American Concrete Institute). 2015. Guide for the design and construction of concrete reinforced with fibre-reinforced polymer (FRP) bars. ACI 440.1R-15. Farmington Hills, MI: ACI.
ACI (American Concrete Institute). 2019. Building code requirements for structural concrete (ACI 318-19) and commentary on building code requirements for structural concrete (ACI 318R-19). ACI Committee 318. Farmington Hills, MI: ACI.
Ali, A. H., H. M. Mohamed, C. E. Chalioris, and A. Deifalla. 2021. “Evaluating the shear design equations of FRP-reinforced concrete beams without shear reinforcement.” Eng. Struct. 235: 112017. https://doi.org/10.1016/j.engstruct.2021.112017.
Ascione, L., G. Mancusi, and S. Spadea. 2010. “Flexural behaviour of concrete beams reinforced with GFRP bars.” Strain 46 (5): 460–469. https://doi.org/10.1111/j.1475-1305.2009.00662.x.
Bentz, E. C., and M. P. Collins. 2006. “Development of the 2004 Canadian Standards Association (CSA) A23.3 shear provisions for reinforced concrete.” Can. J. Civ. Eng. 33 (5): 521–534. https://doi.org/10.1139/l06-005.
Bentz, E. C., L. Massam, and M. P. Collins. 2010. “Shear strength of large concrete members with FRP reinforcement.” J. Compos. Constr. 14 (6): 637–646. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000108.
CSA (Canadian Standard Association). 2010. Specification for fibre-reinforced polymers. CSA Standard S807-10. Mississauga, ON, Canada: CSA.
CSA (Canadian Standard Association). 2017. Design and construction of building structures with fibre-reinforced polymers. CSA Standard S806-12. Mississauga, ON, Canada: CSA.
CSA (Canadian Standard Association). 2019. Design of concrete structures. CSA Standard A23.3-19. Mississauga, ON, Canada: CSA.
Gross, S., J. Yost, D. Dinehart, E. Svensen, and N. Liu. 2003. “Shear strength of normal and high strength concrete beams reinforced with GFRP bars.” In Int. Conf. on High Performance Materials in Bridges, edited by A. Azizinamini, A. Yakel, and M. Abdelrahman, 426–437. Reston, VA: ASCE.
Kim, W., and J. Jeong. 2011. “Decoupling of arch action in shear-critical reinforced concrete beams.” ACI Struct. J. 108 (4): 395–428.
Krall, M., and M. Polak. 2018. “Testing and strut-and-tie modelling of beams with GFRP reinforcements.” ACI Symp. Publ. 322: 11.1–11.12.
Krall, M., and M. A. Polak. 2019. “Concrete beams with different arrangements of GFRP flexural and shear reinforcement.” Eng. Struct. 198: 109333. https://doi.org/10.1016/j.engstruct.2019.109333.
Krall, M. D. 2014. “Tests on concrete beams with GFRP flexural and shear reinforcements & analysis method for indeterminate strut-and-tie models with brittle reinforcements.” MASc thesis, Dept. of Engineering Civil and Environmental Engineering, Univ. of Waterloo.
Machial, R., M. Shahria Alam, and A. Rteil. 2012. “Revisiting the shear design equations for concrete beams reinforced with FRP rebar and stirrup.” Mater. Struct. 45 (11): 1593–1612. https://doi.org/10.1617/s11527-012-9859-5.
Nagasaka, T., H. Fukuyama, and M. Tanigaki. 1993. “Shear performance of concrete beams reinforced with FRP stirrups.” Spec. Publ. ACI 138 (47): 789–812.
Nakamura, H., and T. Higai. 1995. “Evaluation of shear strength of concrete beams reinforced with FRP.” [In English.] Concr. Libr. Int. JSCE 26: 111–123.
Razaqpur, A. G., and S. Spadea. 2015. “Shear strength of FRP reinforced concrete members with stirrups.” J. Compos. Constr. 19 (1): 4014025. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000483.
Tedford, T. 2019. Experimental investigation of the shear behaviour of slender concrete beams reinforced with GFRP. Waterloo, ON, Canada: Univ. of Waterloo.
Yost, J., S. Gross, and D. Dinehart. 2001. “Shear strength of normal strength concrete beams reinforced with deformed GFRP bars.” J. Compos. Constr. 5 (4): 268–275.
Information & Authors
Information
Published In
Copyright
© 2022 American Society of Civil Engineers.
History
Received: Aug 12, 2021
Accepted: May 26, 2022
Published online: Jul 21, 2022
Published in print: Oct 1, 2022
Discussion open until: Dec 21, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- R. Barrage, M.A. Polak, Flexural and shear behaviours of GFRP-reinforced concrete beams based on nonlinear finite element studies, Canadian Journal of Civil Engineering, 10.1139/cjce-2022-0179, 50, 2, (90-101), (2023).