Experimental Investigation and Modeling of FRP–Concrete Joint Bond Strength Based on Failure Depth
Publication: Journal of Composites for Construction
Volume 25, Issue 6
Abstract
The growing interest in fiber-reinforced polymer (FRP) composites in recent years for use in strengthening concrete structures bears witness to their efficiency and ease of use. A major issue in FRP strengthening designs, however, is the determination of the bond strength (ultimate load capacity) of the FRP strips, which is quite dependent on their debonding off the concrete substrate. Identification of the major parameters involved in the FRP–concrete bond capacity forms an important step toward its prediction. The parameters commonly considered in previous models include the geometric and mechanical properties of FRP sheets as well as the properties of both the concrete and the adhesive material used as determinants of bond strength. The present study, however, explores the additional parameter of cement-to-aggregate weight ratio for its effect on the failure plane. In the experimental phase of the study, a wide range of FRP strips is used in three different series of concrete specimens to investigate the failure plane in each. Based on the post-test conditions of the specimens, a novel method is adopted for the first time to measure the failure depth of the externally bonded reinforcement (EBR) strengthening technique. Accordingly, the depth of the failure plane is expressed as a function of the cement-to-aggregates weight ratio. In the second phase, an analytical model is developed that draws upon interfacial fracture energy and in which failure depth is introduced as one of the parameters involved in interfacial fracture energy. The unknown parameters of the new model are then derived based on 196 specimens (85% of the data set) from the experimental results of the present study and the extracted data from previous studies. Finally, the model is validated against three existing well-known ones using 35 random specimens (15% of the data set) of the database to show the satisfactory performance of the proposed model.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors would like to express their appreciation to the staff of the Structural Laboratory of the Department of Civil Engineering of Isfahan University of Technology (IUT) for their support and valuable suggestions in the process of this study.
References
Achintha, M., and C. Burgoyne. 2013. “Fracture energy of the concrete–FRP interface in strengthened beams.” Eng. Fract. Mech. 110: 38–51. https://doi.org/10.1016/j.engfracmech.2013.07.016.
ACI (American Concrete Institute). 2017. Guide for the design and construction of externally bonded FRP systems for strengthening concrete structures. ACI 440.2R. Farmington Hills, MI: ACI.
Ali-Ahmad, M., K. Subramaniam, and M. Ghosn. 2006. “Experimental investigation and fracture analysis of debonding between concrete and FRP sheets.” J. Eng. Mech. 132 (9): 914–923. https://doi.org/10.1061/(ASCE)0733-9399(2006)132:9(914).
ASTM. 2017. Standard test method for tensile properties of polymer matrix composite materials. ASTM D3039/D3039M. West Conshohocken, PA: ASTM.
ASTM. 2019. Standard practice for making and curing concrete test specimens in the laboratory. ASTM C192/C192M-19. West Conshohocken, PA: ASTM.
Barham, W. S., Y. T. Obaidat, and A. I. Al-Maabreh. 2019. “Effect of aggregate size on the bond behavior between carbon fiber-reinforced polymer sheets and concrete.” J. Mater. Civ. Eng. 31 (12): 04019295. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002950.
Bažant, Z. P., and E. Becq-Giraudon. 2002. “Statistical prediction of fracture parameters of concrete and implications for choice of testing standard.” Cem. Concr. Res. 32 (4): 529–556. https://doi.org/10.1016/S0008-8846(01)00723-2.
Chen, J. F., and J. G. Teng. 2001. “Anchorage strength models for FRP and steel plates bonded to concrete.” J. Struct. Eng. 127 (7): 784–791. https://doi.org/10.1061/(ASCE)0733-9445(2001)127:7(784).
Dai, J., T. Ueda, and Y. Sato. 2005. “Development of the nonlinear bond stress–slip model of fiber reinforced plastics sheet–concrete interfaces with a simple method.” J. Compos. Constr. 9 (1): 52–62. https://doi.org/10.1061/(ASCE)1090-0268(2005)9:1(52).
Ghorbani, M., D. Mostofinejad, and A. Hosseini. 2017. “Experimental investigation into bond behavior of FRP-to-concrete under mixed-mode I/II loading.” Constr. Build. Mater. 132: 303–312. https://doi.org/10.1016/j.conbuildmat.2016.11.057.
Girgin, Z. C., N. Arioglu, and E. Arioglu. 2007. “Evaluation of strength criteria for very-high-strength concrete under triaxial compression.” ACI Struct. J. 104 (3): 278.
Hosseini, A., and D. Mostofinejad. 2014. “Effective bond length of FRP-to-concrete adhesively-bonded joints: Experimental evaluation of existing models.” Int. J. Adhes. Adhes. 48: 150–158. https://doi.org/10.1016/j.ijadhadh.2013.09.022.
Lin, J. P., Y. F. Wu, and S. T. Smith. 2017. “Width factor for externally bonded FRP-to-concrete joints.” Constr. Build. Mater. 155: 818–829. https://doi.org/10.1016/j.conbuildmat.2017.08.104.
Lu, X. Z., J. G. Teng, L. P. Ye, and J. J. Jiang. 2005. “Bond–slip models for FRP sheets/plates bonded to concrete.” Eng. Struct. 27 (6): 920–937. https://doi.org/10.1016/j.engstruct.2005.01.014.
Maeda, T., Y. Asano, Y. Sato, T. Ueda, and Y. Kakuta. 1997. “A study on bond mechanism of carbon fiber sheet.” In Vol 1. of Proc., 3rd Int. Symp. of Non-Metallic (FRP) Reinforcement for Concrete Structures, 279–286. Sapporo, Japan: Japan Concrete Institute.
Moghaddas, A., and D. Mostofinejad. 2019. “Empirical FRP–concrete bond strength model for externally bonded reinforcement on grooves.” J. Compos. Constr. 23 (2): 04018080. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000924.
Moghaddas, A., D. Mostofinejad, A. Saljoughian, and E. Ilia. 2021. “An empirical FRP–concrete bond–slip model for externally-bonded reinforcement on grooves.” Constr. Build. Mater. 281: 122575. https://doi.org/10.1016/j.conbuildmat.2021.122575.
Mohammadi, M., D. Mostofinejad, and M. Barghian. 2017. “Effects of surface preparation method on FRP–concrete bond strength under alkaline conditions.” J. Compos. Constr. 21 (4): 04017010. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000786.
Mostofinejad, D., B. Arefian, and A. Hosseini. 2014. “Influence of FRP width on bond strength of FRP-to-concrete.” In Proc., 4th Int. Conf. on Composites: Characterization, Fabrication and Application (CCFA-4), 1–2. Tehran, Iran: Iran Composites Institute.
Mostofinejad, D., M. H. Mofrad, A. Hosseini, and H. H. Mofrad. 2018. “Investigating the effects of concrete compressive strength, CFRP thickness and groove depth on CFRP–concrete bond strength of EBROG joints.” Constr. Build. Mater. 189: 323–337. https://doi.org/10.1016/j.conbuildmat.2018.08.203.
Mostofinejad, D., K. Sanginabadi, and M. R. Eftekhar. 2019. “Effects of coarse aggregate volume on CFRP–concrete bond strength and behavior.” Constr. Build. Mater. 198: 42–57. https://doi.org/10.1016/j.conbuildmat.2018.11.188.
Niedermeier, R. 2000. “Envelope line of tensile forces while using externally bonded reinforcement.” [In German.] Doctoral dissertation, Dept. of Civil Engineering, Technical University of Munich (TUM).
Pan, J., and C. K. Leung. 2007. “Effect of concrete composition on FRP/concrete bond capacity.” J. Compos. Constr. 11 (6): 611–618. https://doi.org/10.1061/(ASCE)1090-0268(2007)11:6(611).
Pham, H. B., and R. Al-Mahaidi. 2007. “Modelling of CFRP–concrete shear-lap tests.” Constr. Build. Mater. 21 (4): 727–735. https://doi.org/10.1016/j.conbuildmat.2006.06.012.
Sanginabadi, K., and D. Mostofinejad. 2021. “Effect of aggregate content on the CFRP–concrete effective bond length: An experimental and analytical study.” Compos. Struct. 269: 114044. https://doi.org/10.1016/j.compstruct.2021.114044.
Seracino, R., M. R. Raizal Saifulnaz, and D. J. Oehlers. 2007. “Generic debonding resistance of EB and NSM plate-to-concrete joints.” J. Compos. Constr. 11 (1): 62–70. https://doi.org/10.1061/(ASCE)1090-0268(2007)11:1(62).
Sharma, S. K., M. M. Ali, D. Goldar, and P. K. Sikdar. 2006. “Plate–concrete interfacial bond strength of FRP and metallic plated concrete specimens.” Composites, Part B 37 (1): 54–63. https://doi.org/10.1016/j.compositesb.2005.05.011.
Standards Australia. 2008. Design handbook for RC structures retrofitted with FRP and metal plates: Beams and slabs. Sydney, NSW: Standards Australia.
Ueno, S. 2012. “Introduction of a stress state criterion to predict bond strength between FRP and concrete substrate.” Doctoral dissertation, Dept. of Civil and Environmental Engineering, Univ. of Alabama.
Wu, Y. F., and C. Jiang. 2013. “Quantification of bond–slip relationship for externally bonded FRP-to-concrete joints.” J. Compos. Constr. 17 (5): 673–686. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000375.
Wu, Y. F., and Y. W. Zhou. 2010. “Unified strength model based on Hoek–Brown failure criterion for circular and square concrete columns confined by FRP.” J. Compos. Constr. 14 (2): 175–184. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000062.
Wu, Y. F., Z. Zhou, Q. Yang, and W. Chen. 2010. “On shear bond strength of FRP–concrete structures.” Eng. Struct. 32 (3): 897–905. https://doi.org/10.1016/j.engstruct.2009.12.017.
Wu, Z., H. Yuan, and H. Niu. 2002. “Stress transfer and fracture propagation in different kinds of adhesive joints.” J. Eng. Mech. 128 (5): 562–573. https://doi.org/10.1061/(ASCE)0733-9399(2002)128:5(562).
Xue, W., L. Zeng, and Y. Tan. 2008. “Experimental studies on bond behaviour of high strength CFRP plates.” Composites, Part B 39 (4): 592–603. https://doi.org/10.1016/j.compositesb.2007.09.002.
Yin, Y. S., and Y. F. Fan. 2018a. “Roughness effects on the fracture energy between FRP and concrete.” IOP Conf. Ser.: Mater. Sci. Eng. 389: 012016. https://doi.org/10.1088/1757-899X/389/1/012016.
Yin, Y. S., and Y. F. Fan. 2018b. “Influence of roughness on shear bonding performance of CFRP–concrete interface.” Materials 11 (10): 1875. https://doi.org/10.3390/ma11101875.
Yuan, H., J. G. Teng, R. Seracino, Z. S. Wu, and J. Yao. 2004. “Full-range behavior of FRP-to-concrete bonded joints.” Eng. Struct. 26 (5): 553–565. https://doi.org/10.1016/j.engstruct.2003.11.006.
Yuan, H., Z. Wu, and H. Yoshizawa. 2001. “Theoretical solutions on interfacial stress transfer of externally bonded steel/composite laminates.” J. Struct. Mech. Earthquake Eng. 675 (1): 27–39. https://doi.org/10.2208/jscej.2001.675_27.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Oct 22, 2020
Accepted: Jul 13, 2021
Published online: Aug 31, 2021
Published in print: Dec 1, 2021
Discussion open until: Jan 31, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Azad Yazdani, Khaled Sanginabadi, Mohammad-Sadegh Shahidzadeh, Sanaz Razmyan, Mohammad-Rashid Salimi, Davood Mostofinejad, Evaluation of Existing FRP-to-Concrete Bond Strength Models Using Data Envelopment Analysis, Journal of Composites for Construction, 10.1061/JCCOF2.CCENG-4103, 27, 3, (2023).
- Yan-Jie Wang, Zhi-Min Wu, Hong-Bo Liu, Qi-Meng Zhang, Shu-Tong Yang, Yan-Cang Li, Influence of thermal effects on debonding response of CFRP-to-concrete/steel interfaces under thermal and mechanical loads: An analytical solution, Composite Structures, 10.1016/j.compstruct.2022.116333, 303, (116333), (2023).
- Effects of Different Groove Classes Used in Externally Bonded Reinforcement on Grooves Joints on Carbon Fiber-Reinforced Polymer-to-Concrete Bond Behavior, ACI Structural Journal, 10.14359/51734656, 119, 4, (2022).
- Pengda Li, Jingqi Zeng, Weiwen Li, Yao Zhao, Effect of concrete heterogeneity on interfacial bond behavior of externally bonded FRP-to-concrete joints, Construction and Building Materials, 10.1016/j.conbuildmat.2022.129483, 359, (129483), (2022).
- Feng Zhang, Lei Gao, Qian Wei, Theoretical and numerical bonding capacity model of FRP-to-concrete joints with mechanical fastening, Construction and Building Materials, 10.1016/j.conbuildmat.2022.129066, 353, (129066), (2022).
- Fatemeh Mohammadi Ghahsareh, Davood Mostofinejad, Effects of groove angle and pattern on CFRP-to-concrete bond behavior of EBROG joints: Comparison of diagonal with longitudinal and transverse grooves, Construction and Building Materials, 10.1016/j.conbuildmat.2022.127980, 342, (127980), (2022).
- Khaled Sanginabadi, Azad Yazdani, Davood Mostofinejad, Christoph Czaderski, RC members externally strengthened with FRP composites by grooving methods including EBROG and EBRIG: A state-of-the-art review, Construction and Building Materials, 10.1016/j.conbuildmat.2022.126662, 324, (126662), (2022).
- Khaled Sanginabadi, Azad Yazdani, Davood Mostofinejad, Christoph Czaderski, Bond behavior of FRP composites attached to concrete using EBROG method: A state-of-the-art review, Composite Structures, 10.1016/j.compstruct.2022.116060, 299, (116060), (2022).
- Ki-Sun Choi, Dongkeun Lee, Young-Chan You, Sang Whan Han, Long-term performance of 15-year-old full-scale RC beams strengthened with EB FRP composites, Composite Structures, 10.1016/j.compstruct.2022.116055, 299, (116055), (2022).
- Shutong Yang, Chang Liu, Zhongke Sun, Mingqi Xu, Yaodong Feng, Effects of resin pre-coating treatment and fibre reinforcement on adhesive bonding between CFRP sheet and concrete, Composite Structures, 10.1016/j.compstruct.2022.115610, 292, (115610), (2022).
- See more