Influence of Changes in Cross Section on the Effectiveness of Externally Bonded FRP Strengthening
Publication: Journal of Composites for Construction
Volume 13, Issue 3
Abstract
There are many situations where strengthening might be required for a nonprismatic reinforced concrete section (i.e., a beam or slab where the depth of the section varies along its length). For example, many bridges in the United Kingdom have inadequate capacity to carry accidental vehicle loads on verges. These shallow depth verges are often cantilevered from the much deeper main bridge deck. The cantilever might be strengthened by applying fiber-reinforced polymer (FRP) composites to the top surface of the cantilever, extending transversely onto the bridge deck. However, a problem may exist with such a situation due to the potential for a dramatic reduction in the degree of strengthening which is achievable. This is due to the effects of cracking, and longitudinal shear stresses. Tests presented in this paper demonstrate that in regions where little or no cracking occurs, local or global debonding of the external FRP may result. Therefore, the strength of some nonprismatic beams, as predicted by current design guidelines, is often shown to be overly conservative and, in one case significantly unconservative. However, more importantly, the predicted failure modes and FRP strains often do not correspond to those observed. Advice on the best approach for analyzing these beams is given.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers gratefully acknowledge the work of David Cartwright and the technicians at the University of Bath in carrying out the tests presented in this paper.
References
American Concrete Institute (ACI) Committee 440. (2002). “Guide for the design and construction of externally bonded FRP systems for strengthening concrete structures.” ACI 440.2R-02, Detroit.
Blaschko, M., Niedermeier, R., and Zilch, K. (1998). “Bond failure modes of flexural members strengthened with FRP.” Proc., 2nd Int. Conf. on Composites in Infrastructure, Tucson, Ariz., 315–327.
Concrete Society. (2004). “Design guidance for strengthening concrete structures using fibre composite materials.” Technical Rep. No. 55, 2nd Ed., Camberley, U.K.
Fédération Internationale du Béton (FIB). (2001). “Externally bonded, FRP reinforcement for RC structures.” Bulletin 14, Lausanne, Switzerland.
Liu, I. S. T., Oehlers, D. J., and Seracino, R. (2007). “Study of intermediate crack debonding in adhesively plated beams.” J. Compos. Constr., 11(2), 175–183.
Maeda, T., Asano, Y., Sato, Y., Ueda, T., and Katuto, Y. (1997). “A study on bond mechanism of carbon fibre sheet.” Nonmetallic (FRP) Reinforcement for Concrete Structures, Proc., 3rd Int. Symp., Sapporo, Japan, Japan Concrete Institute, Tokyo, 279–285.
Neubauer, U., and Rostasy, F. S. (1997). “Design aspects of concrete structures strengthened with externally bonded CFRP-plates.” Proc., 7th Int. Conf. on Structural Faults and Repair, Edinburgh, U.K., ECS Publications, Edinburgh, 109–118.
Niedermeier, R. (2000). “Zugkraftdeckung bei klebearmierten bauteilen.” Doctoral dissertation, TU München, München, Germany, in German.
Niu, H., and Wu, Z. (2005). “Numerical analysis of debonding mechanisms in FRP-strengthened RC beams.” Comput. Aided Civ. Infrastruct. Eng., 20(5), 354–368.
Information & Authors
Information
Published In
Copyright
© 2009 ASCE.
History
Received: Jun 10, 2008
Accepted: Oct 25, 2008
Published online: May 15, 2009
Published in print: Jun 2009
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.