Modeling Damage and Failure in Pretensioned Concrete Girders Fabricated with Large-Diameter Strands
Publication: Journal of Bridge Engineering
Volume 24, Issue 8
Abstract
Pretensioned concrete elements are commonly fabricated with strands 12.7 or 15.2 mm (0.5 or 0.6 in.) in diameter; however, the industry has seen interest in using larger-diameter strands in recent years. The use of larger-diameter strands results in greater transverse tensile stresses within the girder end regions, which may increase cracking at the time of prestress transfer. Such cracks may continue to grow during service and cause durability concerns. Moreover, increased damage around the strands and at the web–flange interfaces may lead to unconventional failure mechanisms, such as anchorage-induced or horizontal shear failures. This paper introduces a modeling approach for investigating the performance of pretensioned girders fabricated with strands 17.8 mm (0.7 in.) in diameter from prestress transfer until failure under shear-critical loading. Data from seven full-scale prestress transfer tests and 10 load tests showed that the model can capture the transfer lengths, end-region stresses, and cracking at prestress transfer as well as load-deflection response and failure modes. Subsequently, three remedial end-region reinforcement details were investigated using the validated approach to examine their efficacy in controlling end-region cracks and stresses.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The research presented in this paper was financially supported by the Texas Department of Transportation (TxDOT). The findings, opinions, and recommendations presented in this paper are those of the authors and do not necessarily represent the views of TxDOT.
References
AASHTO. 2016. AASHTO LRFD bridge design specifications. 7th ed., with 2015 and 2016 interim revisions. Washington, DC: AASHTO.
ACI (American Concrete Institute). 2001. Control of cracking in concrete structures. ACI 224. Farmington Hills, MI: ACI.
Alirezaei Abyaneh, R. 2016. “Computational modeling of prestress transfer, end-region cracks and shear behavior in prestressed concrete I-girders employing large-diameter strands.” Master’s thesis, Univ. of Texas at Austin.
Arab, A. A. 2012. “Finite element modeling of pretensioned concrete girders: A methodological approach with applications in large strands and end zone cracking.” Ph.D. dissertation, George Washington Univ.
ASTM. 2015. Standard specification for deformed and plain carbon-steel bars for concrete reinforcement. ASTM A615/A615M. West Conshohocken, PA: ASTM.
Avendaño, A. 2008. “Shear strength and behavior of prestressed concrete beams.” Master’s thesis, Univ. of Texas at Austin.
Bigaj, A. J. 1999. Structural dependence of rotations capacity of plastic hinges in RC beams and slabs. Delft, Netherland: Delft Univ. of Technology.
Červenka, V., L. Jendele, and J. Červenka. 2016. ATENA program documentation part 1. Prague, Czech Republic: Červenka Consulting.
fib (International Federation for Structural Concrete). 2013. fib model code for concrete structures 2010. Berlin: fib.
Hovell, C., A. Avendaño, A. Moore, D. Dunkman, O. Bayrak, and J. Jirsa. 2012. Structural performance of Texas U-Beams at prestress transfer. Austin, TX: Univ. of Texas at Austin Center for Transportation Research.
Hoyer, E., and E. Friedrich. 1939. “Beitrag zur frage der haftspannung in eisenbetonbauteilen [Contribution to the question of bond in concrete elements].” [In German.] Beton Eisen 30 (6): 107–110.
Katz, A., H. Yousefpour, H. Kim, A. R. Abyaneh, J. Salazar, T. Hrynyk, and O. Bayrak. 2017. “Shear performance of pretensioned concrete I-girders employing 0.7 in. (17.8 mm) strands.” Struct. J. 114: 1273–1284.
Kim, H., R. Bonetti, A. Longshaw, H. Yousefpour, T. Hrynyk, and O. Bayrak. 2018. “End-region cracking in pretensioned concrete girders employing 0.7-in. strands: Time-dependent and service-load effects.” In Proc., PCI 2018 Convention and National Bridge Conf. Chicago: PCI.
Kim, H., A. Katz, J. Salazar, R. Abyaneh, H. Yousefpour, T. Hrynyk, and O. Bayrak. 2017. “End-Region Serviceability and Shear Strength of Precast, Pretensioned I-girders employing 0.7-in. diameter strands.” In Proc., PCI 2017 Convention and National Bridge Conf. Chicago: PCI.
Longshaw, A. T. 2018. “Development of end-region cracks in pretensioned concrete I-girders employing 0.7-in. diameter strands.” Electronic thesis, Univ. of Texas at Austin.
Morcous, G., S. Assad, A. Hatami, and M. Tadros. 2014. “Implementation of 0.7 in. diameter strands at 2.0 × 2.0 in. spacing in pretensioned bridge girders.” PCI J. 59 (3): 145–158. https://doi.org/10.15554/pcij.06012014.145.158.
Morcous, G., K. Hanna, and M. Tadros. 2011. “Use of 0.7-in. diameter strands in pretensioned bridge girders.” PCI J. 56 (4): 65–82. https://doi.org/10.15554/pcij.09012011.65.82.
NCHRP (National Cooperative Highway Research Program). 2010. Evaluation and repair procedures for precast/prestressed concrete girders with longitudinal cracking in the web. NCHRP Rep. 654. Washington, DC: NCHRP.
O’Callaghan, M. 2007. “Tensile stresses in the end regions of pretensioned I-Beams at release.” Electronic thesis, Univ. of Texas at Austin.
Okumus, P., R. P. Kristam, and M. D. Arancibia. 2016. “Sources of crack growth in pretensioned concrete-bridge girder anchorage zones after detensioning.” J. Bridge Eng. 21 (10): 04016072. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000928.
Okumus, P., and M. G. Oliva. 2013. “Evaluation of crack control methods for end zone cracking in prestressed concrete bridge girders.” PCI J. 58 (2): 91–105. https://doi.org/10.15554/pcij.03012013.91.105.
Okumus, P., M. G. Oliva, and S. Becker. 2012. “Nonlinear finite element modeling of cracking at ends of pretensioned bridge girders.” Eng. Struct. 40: 267–275. https://doi.org/10.1016/j.engstruct.2012.02.033.
Patzlaff, Q., G. Morcous, K. Hanna, and M. Tadros. 2012. “Bottom flange confinement reinforcement in precast prestressed concrete bridge girders.” J. Bridge Eng. 17 (4): 607–616. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000287.
PCI (Precast/Prestressed Concrete Institute) Committee on Bridges. 2006. Manual for the evaluation and repair of precast, prestressed concrete bridge products. MNL-137-06, Chicago: PCI.
Ross, B. E., M. D. Willis, H. R. Hamilton, and G. R. Consolazio. 2014. “Comparison of details for controlling end-region cracks in precast, pretensioned concrete I-girders.” PCI J. 59 (2): 96–108. https://doi.org/10.15554/pcij.03012014.96.108.
Salazar, J. L., H. Yousefpour, A. R. Abyaneh, H. Kim, A. T. Katz, T. Hrynyk, and O. Bayrak. 2018. “End-region behavior of pretensioned I-girders employing 0.7 in. (17.8 mm) strands.” Struct. J. 115: 91–102. https://doi.org/10.14359/51700783.
Salazar, J., H. Yousefpour, A. Katz, R. Alirezaei Abyaneh, H. Kim, D. Garber, T. Hrynyk, and O. Bayrak. 2017. “Benefits of using 0.7-inch strands in precast, pretensioned girders: A parametric investigation.” PCI J. 62 (6): 59–75.
Song, W., Z. J. Ma, J. Vadivelu, and E. G. Burdette. 2014. “Transfer length and splitting force calculation for pretensioned concrete girders with high-capacity strands.” J. Bridge Eng. 19 (7): 04014026. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000566.
Tadros, M. K., and G. Morcous. 2011. Impact of 0.7 inch diameter strands on NU I-girders. Technical Rep. Lincoln, NE: Nebraska Dept. of Roads.
Texas Department of Transportation. 2014. Standard specifications for construction and maintenance of highways, streets, and bridges. Austin, TX: Texas Dept. of Transportation.
Vadivelu, J. 2009. “Impact of larger diameter strands on AASHTO/PCI bulb-tees.” Master’s thesis, Univ. of Tennessee.
Information & Authors
Information
Published In
Copyright
© 2019 American Society of Civil Engineers.
History
Received: Aug 3, 2018
Accepted: Feb 11, 2019
Published online: May 16, 2019
Published in print: Aug 1, 2019
Discussion open until: Oct 16, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.