Performance of Light-Frame Timber Shear Walls Produced with Weathered Sheathing
Publication: Journal of Architectural Engineering
Volume 26, Issue 1
Abstract
Light-frame wood construction is the most common construction method used for single- and multifamily residential structures in the United States. Shear walls made with engineered wood structural panels are the primary lateral force resisting system in these structures. Although shear walls are expected to be protected from prolonged or severe exposure to moisture, situations such as flooding and compromised building envelopes have the potential to expose shear walls to high levels of moisture and subsequently alter their properties. The specific contribution of moisture degradation in engineered wood structural panels on shear wall performance was investigated in this study by subjecting oriented strand board (OSB) and plywood to accelerated weathering prior to shear wall assembly. Shear walls () were tested by using a monotonic loading protocol to compare performance between walls produced with standard sheathing and those produced after sheathing had been weathered and dried. Statistically significant losses in yield load, shear capacity, and energy dissipation from moisture degradation during accelerated weathering were determined for OSB walls, while none were present for plywood walls. In addition, localized strain in the sheathing near fasteners in the uplift corner was monitored by using digital image correlation, which showed differences in strain distribution for both OSB and plywood walls constructed with weathered sheathing.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Financial support was provided by the Wood-Based Composites Center, a National Science Foundation (NSF) Industry/University Cooperative Research Center (Project No. IIP-1624599). The laboratory assistance of Milo Clauson, Ian Morrell, and Micah Sutfin is greatly appreciated.
References
Adams, N. R. 1966. Plywood shear walls. Tacoma, WA: American Plywood Association.
Alexopoulos, J. 1992. “Accelerated aging and outdoor weathering of aspen waferboard.” For. Prod. J. 44 (2): 15–22.
Alldritt, K., A. Sinha, and T. H. Miller. 2014. “Designing a strand orientation pattern for improved shear properties of oriented strand board.” J. Mater. Civ. Eng. 26 (7): 0401422. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001033.
Anderson, E. N., R. J. Leichti, E. G. Sutt, and D. V. Rosowsky. 2007. “Sheathing nail bending-yield stress: Effect on cyclic performance of wood shear walls.” Wood Fiber Sci. 39 (4): 536–547.
APA (The Engineered Wood Association). 2010. PS 1-09 structural plywood. Tacoma, WA: APA.
APA (The Engineered Wood Association). 2015. Structural panel wall sheathing market shares for 2014. Tacoma, WA: APA.
APA (The Engineered Wood Association). 2018. Performance standards and qualification policy for wood structural panels. APA PRP-108. Tacoma, WA: APA.
ASCE and SEI (Structural Engineering Institute). 2014. Seismic evaluation and retrofit of existing buildings. Reston, VA: ASCE.
ASTM. 2012. Standard practice for static load test for shear resistance to framed walls for buildings. ASTM E564. West Conshohocken, PA: ASTM.
ASTM. 2015. Standard test methods of conducting strength tests of panels for building construction. ASTM E72. West Conshohocken, PA: ASTM.
ASTM. 2016. Standard test methods for direct moisture content measurement of wood and wood-based materials. ASTM D4442. West Conshohocken, PA: ASTM.
AWC. 2015b. Special design provisions for wind and seismic. Leesburg, VA: AWC.
AWC (American Wood Council). 2015a. National design specification (NDS) for wood construction. Leesburg, VA: AWC.
Biblis, E. 2000. “Effect of weathering on surface quality and structural properties of six species of untreated commercial plywood siding after 6 years of exposure in Alabama.” For. Prod. J. 50 (5): 47–50.
Bowyer, J., R. Shmulsky, and J. G. Haygreen. 2007. “Structural panels.” Chapter 14 in Forest products and wood science, 353–381. Ames, IA: Blackwell.
Bradley, A., W.-S. Chang, and R. Harris. 2015. “The effect of drying on timber frame connections post flooding.” Proc. Inst. Civ. Eng. Constr. Mater. 168 (3): 144–157. https://doi.org/10.1680/coma.14.00042.
Bradley, A. C., W. S. Chang, and R. Harris. 2016. “The effect of simulated flooding on the structural performance of light frame timber shear walls—An experimental approach.” Eng. Struct. 106 (Jan): 288–298. https://doi.org/10.1016/j.engstruct.2015.10.010.
Breyer, D., K. Cobeen, K. Fridley, and D. Pollock. 2015. Design of wood structures—ASD/LRFD. New York: McGraw Hill-Education.
Cunningham, T. P. 1993. Product evaluation for Metropolitan Dade County, Florida. Tacoma, WA: APA.
Kalkert, R. E., and J. D. Dolan. 1997. “Behavior of 8-d nailed stud-to-sheathing connections.” For. Prod. J. 47 (6): 95–102.
Kim, J. H., S. M. Kent, and D. V. Rosowsky. 2006. “The effect of biological deterioration on the seismic performance of woodframe shearwalls.” Comput.-Aided Civ. Inf. 21 (3): 205–215. https://doi.org/10.1111/j.1467-8667.2006.00428.x.
King, D., A. Sinha, and J. J. Morrell. 2015. “Effect of wetting on performance of small-scale shear walls.” Wood Fiber Sci. 47 (1): 74–83.
Koch, P. 1967. “Minimizing and predicting delamination of southern plywood in exterior exposure.” For. Prod. J. 17 (2): 41–47.
Kojima, Y., H. Norita, and S. Suzuki. 2009. “Evaluating the durability of wood-based panels using thickness swelling results from accelerated aging treatments.” For. Prod. J. 59 (5): 35–41.
Korai, H., and Y. Fujimoto. 2015. “Nail-head pull-through strength and lateral nail resistance strength of wood-based boards subjected to various climatic conditions in Japan.” J. Wood Sci. 61 (4): 401–411. https://doi.org/10.1007/s10086-015-1485-8.
Korai, H., N. Sekino, and H. Saotome. 2012. “Effects of outdoor exposure angle on the deterioration of wood-based board properties.” For. Prod. J. 63 (2): 184–190.
Laleicke, P. F. 2015. “Non-destructive detection and monitoring of durability issues in wood panels under accelerated-weathering.” Ph.D. dissertation, Dept. of Wood Science and Engineering, Oregon State Univ.
Lam, F., H. G. L. Prion, and M. He. 1997. “Lateral resistance of wood shear walls with large sheathing panels.” J. Struct. Eng. 123 (12): 1666–1673. https://doi.org/10.1061/(ASCE)0733-9445(1997)123:12(1666).
Lang, E. M., and J. R. Loferski. 1995. “In-plane hygroscopic expansion of plywood and oriented strandboard.” For. Prod. J. 45 (4): 67–71.
Lang, E. M., J. R. Loferski, and J. D. Dolan. 1995. “Hygroscopic deformation of wood-based composite panels.” For. Prod. J. 45 (3): 67–70.
Leichti, R., R. Staehle, and D. Rosowsky. 2002. “A performance assessment of flood damaged shearwalls.” In Proc., 9th Intl. Conf. on Durability of Materials and Components. Paris: International Union of Laboratories and Experts in Construction Materials, Systems and Structures.
Linton, D., R. Gupta, D. Cox, and J. van de Lindt. 2015. “Load distribution in light-frame wood buildings under experimentally simulated tsunami loads.” J. Perform. Constr. Facil. 29 (1): 04014030. https://doi.org/10.1061/(ASCE)CF.1943-5509.0000487.
McNatt, J. D., and D. McDonald. 1993. “Two accelerated-aging tests for wood-based panels.” For. Prod. J. 43 (7/8): 49–52.
Meza, L., A. Sinha, and J. Morrell. 2013. “Effect of setting during construction on properties of Douglas-fir plywood and oriented strandboard flooring.” For. Prod. J. 63 (5/6): 199–201. https://doi.org/10.13073/FPJ-D-FPJ-D-13-00044.
Mohammad, M. A., and I. Smith. 1996. “Effects of multi-phase moisture conditioning on stiffness of nailed OSB-to-lumber connections.” For. Prod. J. 46 (4): 76.
Moya, L., W. T. Tze, and J. E. Winandy. 2009. “The effect of cyclic relative humidity changes on moisture content and thickness swelling behavior of oriented strandboard.” Wood Fiber Sci. 41 (4): 447–460.
Okkonen, A. E., and B. H. River. 1996. “Outdoor aging of wood-based panels and correlation with laboratory aging: Part 2.” For. Prod. J. 46 (3): 68–74.
Sinha, A., and R. Gupta. 2009. “Strain distribution in OSB and GWB in wood-frame shear walls.” J. Struct. Eng. 135 (6): 666–675. https://doi.org/10.1061/(ASCE)0733-9445(2009)135:6(666).
Suchsland, O., and H. Xu. 1991. “Model analysis of flakeboard variables.” For. Prod. J. 41 (11/12): 55–60.
Sutton, M., J.-J. Orteu, and H. Schreier. 2009. Image correlation for shape, motion and deformation measurements: Basic concepts, theory and applications. New York: Springer.
US Census Bureau. 2018a. “Characteristics of new single-family houses completed.” Accessed March 13, 2019. https://www.census.gov/construction/chars/completed.html.
US Census Bureau. 2018b. “Characteristics of units in new multifamily buildings completed.” Accessed March 13, 2019. https://www.census.gov/construction/chars/mfb.html.
Way, D., F. A. Kamke, and A. Sinha. 2018. “Influence of specimen size during accelerated weathering of wood-based structural panels.” Wood Mater. Sci. Eng. 1–13. https://doi.org/10.1080/17480272.2018.1459836.
Wu, Q., and J. N. Lee. 2002. “Thickness swelling of oriented strandboard under long-term cyclic humidity exposure conditions.” Wood Fiber Sci. 34 (1): 125–139.
Wu, Q., and C. Piao. 1999. “Thickness swelling and its relationship to internal bond strength loss of commercial oriented strandboard.” For. Prod. J. 49 (7/8): 50–55.
Wu, Q., and O. Suchsland. 1997. “Effect of moisture on the flexural properties of commercial oriented strandboards.” Wood Fiber Sci. 29 (1): 47–57.
Xu, W., and P. Winistorfer. 1995. “A procedure to determine thickness swell distribution in wood composite panels.” Wood Fiber Sci. 27 (2): 119–125.
Information & Authors
Information
Published In
Journal of Architectural Engineering
Volume 26 • Issue 1 • March 2020
Copyright
©2019 American Society of Civil Engineers.
History
Received: Aug 20, 2018
Accepted: May 31, 2019
Published online: Oct 31, 2019
Published in print: Mar 1, 2020
Discussion open until: Mar 31, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.