Field Investigation of Moisture Buffering Potential of American Clay and Magnesium Oxide Board in a Mild Climate
Publication: Journal of Architectural Engineering
Volume 24, Issue 4
Abstract
Passive humidity control in buildings can be achieved by incorporating materials that have a moisture-buffering capacity. Such materials absorb moisture at peak-moisture times and give off the stored-up moisture at low moisture times, thereby stabilizing the relative humidity of an interior. The advantages of this phenomenon include energy savings and the improvement of both thermal comfort and perceived air quality. It is necessary to investigate different materials for their moisture-buffering capabilities. In this work, the moisture-buffering potential of American clay and magnesium oxide (MagO) boards was investigated. This was done through a field study that monitored twin buildings under different operation scenarios. One was set as the reference building, and its interior was finished with gypsum, owing to the usage of this material as a common industry practice. The second building was set as the test building and was covered with American clay and MagO boards. The operational congruency of the buildings was checked, and then, three tests were conducted to simulate the interior finishes of a building, ventilation effects, and occupancy density. It was found that the American clay exhibited a better moisture buffering potential than gypsum, especially in the comparison of as-built surface conditions. Further, the experimental results also showed that the moisture-buffering potential of MagO boards may be comparable to that of gypsum, and a coating of vapor-open MagO boards is beneficial for humidity regulation.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors are grateful for the financial support provided by the Natural Sciences and Engineering Research Council of Canada (NSERC), the Canada Research Chair (CRC), and the School of Construction and the Environment at the British Columbia Institute of Technology (BCIT). The contribution of Doug Horn is also acknowledged.
References
Abadie, M. O., and K. C. Mendonça. 2009. “Moisture performance of building materials: From material characterization to building simulation using the moisture buffer value concept.” Build. Environ. 44 (2): 388–401. https://doi.org/10.1016/j.buildenv.2008.03.015.
Allinson, D., and M. Hall. 2010. “Hygrothermal analysis of a stabilised rammed earth test building in the UK.” Energy Build. 42 (6): 845–852. https://doi.org/10.1016/j.enbuild.2009.12.005.
American Clay. n.d. “Technical information.” Accessed November 17, 2018. https://www.americanclay.com/technical-information.
ASHRAE (American Society of Heating, Refrigerating and Air-Conditioning Engineers). 2009. 2009 ASHRAE handbook: Fundamentals. Atlanta, GA.
Barclay, M., N. Holcroft, and A. D. Shea. 2014. “Methods to determine whole building hygrothermal performance of hemp–lime buildings.” Build. Environ. 80: 204–212. https://doi.org/10.1016/j.buildenv.2014.06.003.
Carrer, P., P. Wargocki, A. Fanetti, W. Bischof, E. D. O. Fernandes, T. Hartmann, S. Kephalopolous, S. Palkonen, and O. Seppänen. 2015. “What does the scientific literature tell us about the ventilation–health relationship in public and residential buildings?” Build. Environ. 94 (Part 1): 273–286. https://doi.org/10.1016/j.buildenv.2015.08.011.
Casey, S. P., M. R. Hall, S. C. E. Tsang, and M. A. Khan. 2013. “Energetic and hygrothermal analysis of a nano-structured material for rapid-response humidity buffering in closed environments.” Build. Environ. 60: 24–36. https://doi.org/10.1016/j.buildenv.2012.11.007.
Cerolini, S., M. D’Orazio, C. Di Perna, and A. Stazi. 2009. “Moisture buffering capacity of highly absorbing materials.” Energy Build. 41 (2): 164–168. https://doi.org/10.1016/j.enbuild.2008.08.006.
Clarke, J. A., C. M. Johnstone, N. J. Kelly, R. C. McLean, J. A. Anderson, N. J. Rowan, and J. E. Smith. 1999. “A technique for the prediction of the conditions leading to mould growth in buildings.” Build. Environ. 34 (4): 515–521. https://doi.org/10.1016/S0360-1323(98)00023-7.
Collet, F., J. Chamoin, S. Pretot, and C. Lanos. 2013. “Comparison of the hygric behaviour of three hemp concretes.” Energy Build. 62: 294–303. https://doi.org/10.1016/j.enbuild.2013.03.010.
Dubois, S., A. Evrard, and F. Lebeau. 2013. “Modeling the hygrothermal behavior of biobased construction materials.” J. Build. Phys. 38 (3): 191–213. https://doi.org/10.1177/1744259113489810.
Evrard, A., and A. De Herde. 2009. “Hygrothermal performance of lime-hemp wall assemblies.” J. Build. Phys. 34 (1): 5–25. https://doi.org/10.1177/1744259109355730.
Ge, H., X. Yang, P. Fazio, and J. Rao. 2014. “Influence of moisture load profiles on moisture buffering potential and moisture residuals of three groups of hygroscopic materials.” Build. Environ. 81: 162–171. https://doi.org/10.1016/j.buildenv.2014.06.021.
Ghali, K., O. Katanani, and M. Al-Hindi. 2011. “Modeling the effect of hygroscopic curtains on relative humidity for spaces air conditioned by DX split air conditioning system.” Energy Build. 43 (9): 2093–2100. https://doi.org/10.1016/j.enbuild.2011.04.017.
Gómez, I., S. Guths, R. Souza, J. A. Millan, K. Martín, and J. M. Sala. 2011. “Moisture buffering performance of a new pozolanic ceramic material: Influence of the film layer resistance.” Energy Build. 43 (4): 873–878. https://doi.org/10.1016/j.enbuild.2010.12.007.
Hameury, S. 2005. “Moisture buffering capacity of heavy timber structures directly exposed to an indoor climate: A numerical study.” Build. Environ. 40 (10): 1400–1412. https://doi.org/10.1016/j.buildenv.2004.10.017.
Hansen, K. K., T. Bunch-Nielsen, B. Grelk, and C. Rode. 2016. “Magnesium-oxide boards cause moisture damage inside facades in new Danish buildings.” In Proc., Int. RILEM Conf. on Materials, Systems and Structures in Civil Engineering 2016: Segment on Moisture in Materials and Structures, 151–161. Denmark: Rilem Publications.
Isaksson, T., S. Thelandersson, A. Ekstrand-Tobin, and P. Johansson. 2010. “Critical conditions for onset of mould growth under varying climate conditions.” Build. Environ. 45 (7): 1712–1721. https://doi.org/10.1016/j.buildenv.2010.01.023.
Johansson, P., G. Bok, and A. Ekstrand-Tobin. 2013a. “The effect of cyclic moisture and temperature on mould growth on wood compared to steady state conditions.” Build. Environ. 65: 178–184. https://doi.org/10.1016/j.buildenv.2013.04.004.
Johansson, P., T. Svensson, and A. Ekstrand-Tobin. 2013b. “Validation of critical moisture conditions for mould growth on building materials.” Build. Environ. 62: 201–209. https://doi.org/10.1016/j.buildenv.2013.01.012.
Latif, E., M. Lawrence, A. Shea, and P. Walker. 2015. “Moisture buffer potential of experimental wall assemblies incorporating formulated hemp-lime.” Build. Environ. 93 (Part 2): 199–209. https://doi.org/10.1016/j.buildenv.2015.07.011.
Le, A. D. T., C. Maalouf, T. H. Mai, E. Wurtz, and F. Collet. 2010. “Transient hygrothermal behaviour of a hemp concrete building envelope.” Energy Build. 42 (10): 1797–1806. https://doi.org/10.1016/j.enbuild.2010.05.016.
Liuzzi, S., M. R. Hall, P. Stefanizzi, and S. P. Casey. 2013. “Hygrothermal behaviour and relative humidity buffering of unfired and hydrated lime-stabilised clay composites in a Mediterranean climate.” Build. Environ. 61: 82–92. https://doi.org/10.1016/j.buildenv.2012.12.006.
Mazhoud, B., F. Collet, S. Pretot, and J. Chamoin. 2016. “Hygric and thermal properties of hemp-lime plasters.” Build. Environ. 96: 206–216. https://doi.org/10.1016/j.buildenv.2015.11.013.
McGregor, F., A. Heath, E. Fodde, and A. Shea. 2014a. “Conditions affecting the moisture buffering measurement performed on compressed earth blocks.” Build. Environ. 75: 11–18. https://doi.org/10.1016/j.buildenv.2014.01.009.
McGregor, F., A. Heath, A. Shea, and M. Lawrence. 2014b. “The moisture buffering capacity of unfired clay masonry.” Build. Environ. 82: 599–607. https://doi.org/10.1016/j.buildenv.2014.09.027.
Mlakar, J., and J. Štrancar. 2013. “Temperature and humidity profiles in passive-house building blocks.” Build. Environ. 60: 185–193. https://doi.org/10.1016/j.buildenv.2012.11.018.
Orosa, J. A., and A. Baaliña. 2009. “Improving PAQ and comfort conditions in Spanish office buildings with passive climate control.” Build. Environ. 44 (3): 502–508. https://doi.org/10.1016/j.buildenv.2008.04.013.
Orosa, J. A., and A. C. Oliveira. 2009. “Energy saving with passive climate control methods in Spanish office buildings.” Energy Build. 41 (8): 823–828. https://doi.org/10.1016/j.enbuild.2009.03.004.
Orosa, J. A., and A. C. Oliveira. 2011. “Reducing energy peak consumption with passive climate control methods.” Energy Build. 43 (9): 2282–2288. https://doi.org/10.1016/j.enbuild.2011.05.011.
Osanyintola, O. F., and C. J. Simonson. 2006. “Moisture buffering capacity of hygroscopic building materials: Experimental facilities and energy impact.” Energy Build. 38 (10): 1270–1282. https://doi.org/10.1016/j.enbuild.2006.03.026.
Pedram, S., and F. Tariku. 2015. “Determination of Representative Daily Moisture Production Profile of Occupants in a Residential Setting.” In Proc., of the International Conference on Energy and Environmental Systems Engineering (EESE2015), Beijing, China: WIT Press (WIT Transactions on Engineering Sciences).
Rahim, M., O. Douzane, A. D. T. Le, G. Promis, B. Laidoudi, A. Crigny, B. Dupre, and T. Langlet. 2015. “Characterization of flax lime and hemp lime concretes: Hygric properties and moisture buffer capacity.” Energy Build. 88: 91–99. https://doi.org/10.1016/j.enbuild.2014.11.043.
Rode, C., and K. Grau. 2008. “Moisture buffering and its consequence in whole building hygrothermal modeling.” J. Build. Phys. 31 (4): 333–360. https://doi.org/10.1177/1744259108088960.
Silacote. n.d. “Silacote inorganic mineral silicate coatings: Product support data.” Accessed November 17, 2018. https://www.greenbuildingsupply.com/core/media/media.nl?id=43502&c=772072&h=a34fab1be90fe0b1c5d3.
Stazi, F., A. Nacci, F. Tittarelli, E. Pasqualini, and P. Munafò. 2016. “An experimental study on earth plasters for earthen building protection: The effects of different admixtures and surface treatments.” J. Cult. Heritage 17: 27–41. https://doi.org/10.1016/j.culher.2015.07.009.
Tariku, F., K. Kumaran, and P. Fazio. 2009. “The need for an accurate indoor humidity model for building envelope performance analysis.” In Proc., 4th Int. Building Physics Conf. Istanbul, Turkey: Balkema Publishers.
Tariku, F., K. Kumaran, and P. Fazio. 2011. “Determination of indoor humidity profile using a whole-building hygrothermal model.” Build. Simul. 4 (1): 61–78. https://doi.org/10.1007/s12273-011-0031-x.
Tariku, F., K. Kumaran, and P. Fazio. 2014. “Application of a whole-building hygrothermal model in energy, durability, and indoor humidity retrofit design.” J. Build. Phys. 39 (1): 3–34. https://doi.org/10.1177/1744259114522400.
Tariku, F., and Y. Simpson. 2013. “Development of a whole-building performance research laboratory (WBPRL) for an integrated study of energy efficiency, indoor environmental quality and building envelope durability.” In Proc., Zero Energy Mass Customization Housing, Int. Conf. (ZEMCH2013). Miami, FL: ZEMCH Network.
Wang, Y., Y. Liu, D. Wang, and J. Liu. 2014. “Effect of the night ventilation rate on the indoor environment and air-conditioning load while considering wall inner surface moisture transfer.” Energy Build. 80: 366–374. https://doi.org/10.1016/j.enbuild.2014.05.051.
Woloszyn, M., T. Kalamees, M. O. Abadie, M. Steeman, and A. S. Kalagasidis. 2009. “The effect of combining a relative-humidity-sensitive ventilation system with the moisture-buffering capacity of materials on indoor climate and energy efficiency of buildings.” Build. Environ. 44 (3): 515–524. https://doi.org/10.1016/j.buildenv.2008.04.017.
Yoshino, H., T. Mitamura, and K. Hasegawa. 2009. “Moisture buffering and effect of ventilation rate and volume rate of hygrothermal materials in a single room under steady state exterior conditions.” Build. Environ. 44 (7): 1418–1425. https://doi.org/10.1016/j.buildenv.2008.09.007.
Zhang, H., and H. Yoshino. 2010. “Analysis of indoor humidity environment in Chinese residential buildings.” Build. Environ. 45 (10): 2132–2140. https://doi.org/10.1016/j.buildenv.2010.03.011.
Information & Authors
Information
Published In
Journal of Architectural Engineering
Volume 24 • Issue 4 • December 2018
Copyright
© 2018 American Society of Civil Engineers.
History
Received: Mar 3, 2017
Accepted: Mar 27, 2018
Published online: Jul 19, 2018
Published in print: Dec 1, 2018
Discussion open until: Dec 19, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.