Amplitude-Dependent Damping in Vibration Serviceability: Case of a Laboratory Footbridge
Publication: Journal of Architectural Engineering
Volume 22, Issue 3
Abstract
Construction technology advancements in the last couple of decades have led to the use of lightweight and high-strength materials in structural systems. Although longer spans and lighter materials result in floor systems with less mass, stiffness, and damping, the trend toward a paperless office decreases damping and the amount of live load on the floors even more. Consequently, structures have become more vulnerable to annoying vibrations, and vibration serviceability has become an area of serviceability concern. For vibration serviceability calculations, the damping value of the structural systems is a critical parameter. Damping in structures has proved to be dependent on the amplitude of the applied force on the structure. This condition is referred to as nonlinear damping, or amplitude-dependent damping. Although damping is constant at low and high amplitudes, for in-between amplitudes, the damping value increases with the levels of excitation amplitude. For wind and earthquake excitations, the amplitude-dependent characteristics of damping have been studied extensively in the literature. For floor vibration serviceability applications, even though the nonlinear behavior of damping has been accepted to exist and mentioned in some publications, it is not closely looked at or discussed in detail. The floor vibration serviceability calculations are very sensitive to damping values, but vibration serviceability researchers and practicing engineers are often uncomfortable with assigning a specific number as a damping ratio for a specific mode because of the inconsistency of damping values obtained from different methods. This paper presents a closer look at the amplitude-dependent damping in vibration serviceability and focuses on a laboratory footbridge with experimental and analytical studies. The laboratory footbridge was studied extensively with static and dynamic tests. Three-dimensional finite-element (FE) models were developed, updated, and fine-tuned for two bottom chord extension configurations for both static and dynamic tests. The amplitude-dependent damping behavior of the laboratory footbridge is shown for different amplitudes of sinusoidal excitations. The amplitude-dependent damping ratio values obtained from effective mass calculations proved to be correct with the FE model acceleration predictions. The FE model predictions successfully matched the test results with the nonlinear characteristic introduced for modal damping. One of the most difficult tasks in vibration serviceability research is matching the measured acceleration responses with the FE models, and the success of this paper in matching the acceleration responses for various levels of excitations (with corresponding amplitude-dependent damping values) with the FE model is unique. Successful verification and clarification of the amplitude-dependent phenomenon and FE model matching of measured acceleration responses reinforce the confidence in the FE models in vibration serviceability research by showing that the FE models are reliable not only for natural frequency predictions but also for acceleration response predictions.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The author thanks NUCOR Research and Development for funding the research reported here and the staff of Thomas M. Murray Structural Engineering Laboratory at Virginia Tech for their assistance with construction of the footbridge and the physical testing.
References
Aquino, R., and Tamura, Y. (2013). “Framework for structural damping predictor models based on stick-slip mechanism for use in wind-resistant design of buildings.” J. Wind Eng. Ind. Aerodyn., 117, 25–37.
Avci, O. (2014). “Modal parameter variations due to joist bottom chord extension installations on laboratory footbridges.” J. Perform. Constr. Facil., 04014140.
Avci, O., and Murray, T. M. (2012). “Effect of bottom chord extensions on the static flexural stiffness of open-web steel joists.” J. Perform. Constr. Facil., 620–632.
Avitabile, P. (2008). “Modal space: My coherence is better in some measurements than others when impact testing. Am I doing something wrong?” Exp. Tech., 32(4), 17–18.
Bachmann, H., et al. (1995). Vibration problems in structures, Birkhauser, Basel, Switzerland.
Barrett, A. R. (2006). “Dynamic testing of in-situ composite floors and evaluation of vibration serviceability using the finite element method.” Ph.D. dissertation, Virginia Polytechnic Institute and State Univ., Blacksburg, VA.
Brownjohn, J. M. W., and Pavic, A. (2007). “Experimental methods for estimating modal mass in footbridges using human-induced dynamic excitation.” Eng. Struct., 29(11), 2833–2843.
Butterworth, J., Lee, J., and Davidson, B. (2004). “Experimental determination of modal damping from full scale testing.” Proc., 13th World Conf. on Earthquake Engineering, Vancouver, Canada.
Casini, P., Giannini, O., and Vestroni, F. (2013). “Effect of damping on the nonlinear modal characteristics of a piecewice-smooth system through harmonic forced response.” Mech. Syst. Sig. Process., 36(2), 540–548.
Chang, C. J., and Mohraz, B. (1990). “Modal analysis of nonlinear systems with classical and non-classical damping.” Comput. Struct., 36(6), 1067–1080.
CSI (Computers and Structures, Inc.). (2002). “SAP2000 linear and nonlinear static and dynamic analysis and design of three-dimensional structures- getting started.” Berkeley, CA.
Daoulatli, M. (2010). “Rate of decay of solutions of the wave equation with arbitrary localized nonlinear damping.” Nonlinear Anal. Theory Methods Appl., 73(4), 987–1003.
Davis, D. B. (2008). “Finite element modeling for prediction of low frequency floor vibrations due to walking.” Ph.D. dissertation, Virginia Polytechnic Institute and State Univ., Blacksburg, VA.
De Silva, C. W., ed. (2005). Vibration and shock handbook, CRC Press, Boca Raton, FL.
Díaz, I. M., and Reynolds, P. (2010a). “Acceleration feedback control of human-induced floor vibrations.” Eng. Struct., 32(1), 163–173.
Díaz, I. M., and Reynolds, P. (2010b). “On-off nonlinear active control of floor vibrations.” Mech. Syst. Sig. Process., 24(6), 1711–1726.
Ewins, D. J. (2000). Modal testing: Theory, practice, and application, 2nd Ed., Research Studies Press Ltd., Baldock, Hertfordshire, U.K.
Gromysz, K. (2013). “Verification of the damping model vibrations of reinforced concrete composite slabs.” Procedia Eng., 57, 372–381.
Ho, C., Lang, Z.-Q., and Billings, S. A. (2014). “A frequency domain analysis of the effects of nonlinear damping on the Duffing equation.” Mech. Syst. Sig. Process., 45(1), 49–67.
Hudson, M. J., and Reynolds, P. (2012). “Implementation considerations for active vibration control in the design of floor structures.” Eng. Struct., 44, 334–358.
Ingólfsson, E. T., Georgakis, C. T., Ricciardelli, F., and Jönsson, J. (2011). “Experimental identification of pedestrian-induced lateral forces on footbridges.” J. Sound Vib., 330(6), 1265–1284.
Inman, D. J. (2000). Engineering vibration, 2nd Ed., Prentice Hall, Upper Saddle River, NJ.
Jang, T. S. (2011). “Non-parametric simultaneous identification of both the nonlinear damping and restoring characteristics of nonlinear systems whose dampings depend on velocity alone.” Mech. Syst. Sig. Process., 25(4), 1159–1173.
Jang, T. S. (2013). “A method for simultaneous identification of the full nonlinear damping and the phase shift and amplitude of the external harmonic excitation in a forced nonlinear oscillator.” Comput. Struct., 120, 77–85.
Jeary, A. P. (1986). “Damping in tall buildings—A mechanism and a predictor.” Earthquake Eng. Struct. Dyn., 14(5), 733–750.
Jeary, A. P. (1996). “The description and measurement of nonlinear damping in structures.” J. Wind Eng. Ind. Aerodyn., 59(2–3), 103–114.
Jeary, A. P. (1997). “Damping in structures.” J. Wind Eng. Ind. Aerodyn., 72, 345–355.
Jeary, A. P., and Ellis, B. R. (1981). “Vibration tests of structures at varied amplitudes.” Proc., 2nd Specialty Conf. on Dynamic Response of Structures: Experimentation, Observation, Prediction and Control, ASCE, Reston, VA, 281–294.
Jeary, A. P., and Ellis, B. R. (1983). “On predicting the response of tall buildings to wind excitations.” J. Wind Eng. Ind. Aerodyn., 13(1–3), 173–182.
Leonard, D. R., and Eyre, R. (1975). “Damping and frequency measurements on eight box girders.” Rep. No. LR682, Transport and Road Research Laboratory, Dept. of the Environment, Crowthorne, U.K.
Li, Q., Liu, D., Fang, J., Jeary, A., and Wong, C. (2000). “Damping in buildings: its neural network model and AR model.” Eng. Struct., 22(9), 1216–1223.
Li, Q. S., Yang, K., Wong, C. K., and Jeary, A. P. (2003). “The effect of amplitude-dependent damping on wind-induced vibrations of a super tall building.” J. Wind Eng. Ind. Aerodyn., 91(9), 1175–1198.
Middleton, C. J., and Brownjohn, J. M. W. (2010). “Response of high frequency floors: A literature review.” Eng. Struct., 32(2), 337–352.
Morita, K. O. I. C. H. I., and Kanda, J. (1996). “Experimental evaluation of amplitude dependent natural period and damping ratio of a multi-story structure.” Proc., 11th WCEE.
Pavic, A. (1999). “Vibration serviceability of long-span cast in-situ concrete floors.” PhD thesis, Dept. of Civil and Structural Engineering, Univ. of Sheffield, Sheffield, U.K.
Racic, V., Pavic, A., and Brownjohn, J. M. W. (2009). “Experimental identification and analytical modelling of human walking forces: Literature review.” J. Sound Vib., 326(1), 1–49.
Rainer, J. H. (1979). “Dynamic testing of civil engineering structures.” Proc., Third Canadian Conf. on Earthquake Engineering, 551–574.
Rainer, J. H., and Van Selst, A. (1976). “Dynamic properties of Lions’ gate suspension bridge.” ASCE/EMD Specialty Conf. on Dynamic Response of Structures, 243–252.
Salyards, K., and Noss, N. (2014). “Experimental evaluation of the influence of human-structure interaction for vibration serviceability.” J. Perform. Constr. Facil., 458–465.
Sharma, A., Patidar, V., Purohit, G., and Sud, K. K. (2012). “Effects on the bifurcation and chaos in forced Duffing oscillator due to nonlinear damping.” Commun. Nonlinear Sci. Numer. Simul., 17(6), 2254–2269.
Smith, R. (2001). “Changing the effective mass to control resonance problems.” Sound Vib., 35(5), 14–17.
Spence, S. M. J., Bernardini, E., Guo, Y., Kareem, A., and Gioffrè, M. (2014). “Natural frequency coalescing and amplitude dependent damping in the wind-excited response of tall buildings.” Probab. Eng. Mech., 35, 108–117.
Steinwolf, A., Schwarzendahl, S. M., and Wallaschek, J. (2014). “Implementation of low-kurtosis pseudo-random excitations to compensate for the effects of nonlinearity on damping estimation by the half-power method.” J. Sound Vib., 333(3), 1011–1023.
Sun, C. T., and Lu, Y. P. (1995). Vibration damping of structural elements, Prentice Hall, Upper Saddle River, NJ.
Taillon, J., Légeron, F., and Prud'homme, S. (2012). “Variation of damping and stiffness of lattice towers with load level.” J. Constr, Steel Res., 71, 111–118.
Tamura, Y., and Suganuma, S. (1996). “Evaluation of amplitude-dependent damping and natural frequency of buildings during strong winds.” J. Wind Eng. Ind. Aerodyn., 59(2–3), 115–130.
Tilly, G. P., Cullington, D. W., and Eyre, R. (1984). “Dynamic behaviour of footbridges.” IABSE Surveys S-26/84, No. 2/84, International Association of Bridge and Structural Engineering, Zurich, Switzerland, 13–24.
Van Nimmen, K., Lombaert, G., De Roeck, G., and Van den Broeck, P. (2014). “Vibration serviceability of footbridges: Evaluation of the current codes of practice.” Eng. Struct., 59, 448–461.
Vibrant Technology, Inc. (2003). ME’ScopeVES online help, Scotts Valley, CA.
Wu, J. R., Liu, P. F., and Li, Q. S. (2007). “Effects of amplitude-dependent damping and time constant on wind-induced responses of super tall building.” Comput. Struct., 85(15–16), 1165–1176.
Wyatt, T. A. (1977). “Mechanisms of damping.” Symp. on Dynamic Behaviour of Bridges, Transport and Road Research Laboratory, Crowthorne, U.K., 10–21.
Zapico-Valle, J. L., García-Diéguez, M., and Alonso-Camblor, R. (2013). “Nonlinear modal identification of a steel frame.” Eng. Struct., 56, 246–259.
Zhang, W., and Zhang, H. (1994). “Modeling and analysis of nonlinear damping mechanisms in vibrating systems.” Int. J. Mech. Sci., 36(9), 829–848.
Živanović, S., Pavic, A., and Reynolds, P. (2005). “Vibration serviceability of footbridges under human-induced excitation: A literature review.” J. Sound Vib., 279(1–2), 1–74.
Živanović, S., Pavic, A., and Reynolds, P. (2006). “Modal testing and FE model tuning of a lively footbridge structure.” Eng. Struct., 28(6), 857–868.
Zoghaib, L., and Mattei, P.-O. (2014). “Time and frequency response of structures with frequency dependent, non-proportional linear damping.” J. Sound Vib., 333(3), 887–900.
Information & Authors
Information
Published In
Journal of Architectural Engineering
Volume 22 • Issue 3 • September 2016
Copyright
© 2016 American Society of Civil Engineers.
History
Received: May 11, 2015
Accepted: Jan 11, 2016
Published online: Feb 26, 2016
Discussion open until: Jul 26, 2016
Published in print: Sep 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.