Analysis and Measurement of Buildability Factors Influencing Rebar Installation Labor Productivity of In Situ Reinforced Concrete Walls
Publication: Journal of Architectural Engineering
Volume 18, Issue 1
Abstract
Buildability is one of the most important factors influencing labor productivity. However, an extensive search of the literature revealed a dearth of research into its effects on labor productivity of in situ reinforced concrete construction, especially on the activity levels. Rebar installation is an integral, labor-intensive trade of this type of construction material. Its walls form major parts of reinforced concrete frames, which are typically associated with a higher unit rate cost compared with other structural elements, especially spread foundations and grade and one-way elevated slabs. Therefore, objective of this research is to investigate the effects and relative influence of the rebar diameter, quantity of reinforcement installed, wall thickness, plan geometry, and wall curvature intensity, on rebar installation labor productivity of walls. To achieve this objective, a sufficiently large volume of installation labor productivity data was collected and analyzed using the multiple categorical-regression method. The results obtained show a significant influence of factors investigated on the labor efficiency of the installation operation, which can be used to provide designers feedback on how well their designs consider the requirements of the buildability concept, and the tangible consequences of their decisions on labor productivity. In addition, a set of recommendations are presented, which on implementation, can improve the buildability level of this activity, hence translating into higher labor efficiency and lower labor cost. Moreover, the depicted patterns of factors explored may provide guidance to construction managers for effective activity planning and efficient labor utilization.
Get full access to this article
View all available purchase options and get full access to this article.
References
Adams, S. (1989). Practical buildability, Butterworth-Heinemann Elsevier, Oxford, UK.
Adrian, J. J. (1987). Construction productivity improvement, Prentice Hall, Upper Saddle River, NJ.
Aldana, L. F. (1991). “Measurement and analysis of concrete formwork and steel reinforcement productivity.” M.Sc. dissertation, Dept. of Civil Engineering, Univ. of Dundee, Dundee, UK.
Alshawi, M., and Underwood, J. (1996). “Improving the constructability of design solutions through an integrated system.” J. Eng. Const. Arch. Mgmt., 3(1/2), 47–67.
American Concrete Institute (ACI). (2008) “Building code requirements for structural concrete and commentary.” ACI 318-08, Farmington Hills, MI.
Arditi, D., and Mochtar, K. (2000). “Trends in productivity improvement in the US construction industry.” Constr. Manage. Econ., 18(1), 15–27.
Building and Construction Authority. (2005). Guide to the buildable design appraisal system, Singapore.
Butler, A. J. (1970). The use of cranes on low-rise high density industrialised housing: Report of a working paper, Building Research Station, Watford, UK.
Cheetham, D. W., and Lewis, J. (2001). “Productivity, buildability and constructability: Is work study the missing link?” Proc., 17th Annual ARCOM Conf., Association of Researchers in Construction Management, Edinburgh, UK, 1, 271–280.
Construction Industry Development Board. (1995). The CIDB buildable design appraisal system (BDAS), 3rd Ed., Singapore.
Construction Industry Institute (CII). (1986). Constructability: A primer, Austin, TX.
CII. (1993). Constructability implementation guide, Austin, TX.
Construction Industry Research and Information Association (CIRIA). (1983). “Buildability: An assessment.” Special Publication No. 26, London.
CIRIA. (1999). “Standardisation and pre-assembly: Adding value to construction projects.” Report No. 176, London.
Dong, C. J. (1996). “Effects of design on buildability.” M.Eng. thesis, Nanyang Technological Univ., Singapore.
Emmerson, H. (1962). “Survey of problems before the construction industries.” Her Majesty's Stationary Office (HMSO), London.
Ferguson, I. (1989). Buildability in Practice (Mitchell’s Professional Library), London.
Fischer, M., and Tatum, C. B. (1997). “Characteristics of design-relevant constructability knowledge.” J. Constr. Eng. Manage., 123(3), 253–260.
Griffith, A. (1987). “An investigation into factors influencing buildability and levels of productivity for application to selecting alternative design solutions—A preliminary report.” Proc., CIB W65, Int. Symp. in Organization and Management of Construction, Vol 2, P. R. Lansley and P. A. Harlow, eds., Spon, London, 646–657.
Gujarati, D. N. (1995). Basic econometrics, McGraw-Hill, New York, NY.
Hamilton, L. C. (1992). Regression with graphics, Duxbury Press, Pacific Grove, CA.
Handa, V. K., and Abdalla, O. (1989). “Forecasting productivity by work sampling.” Constr. Manage. Econ., 7(1), 19–28.
Hardy, M. A. (1993). Regression with dummy variables. Sage University Paper series on Quantitative Applications in the Social Sciences, series No. 07-093, Sage Publications, Newbury, CA.
Hidayatalla, N. A. (1992). “A study of labour productivity on reinforcement steel fixing.” M.Sc. dissertation, Dept. of Civil Engineering, Univ. of Dundee, Dundee, UK.
Horner, M., and Duff, R. (2001). More for less: A contractor’s guide to improving productivity in construction, CIRIA, London.
Horner, M., and Zakieh, R. (1996). “Characteristic items—A new approach to pricing and controlling construction projects.” Constr. Manage. Econ., 14(3), 241–252.
Horner, R. M. W., Talhouni, B. T., and Thomas, H. R. (1989). “Preliminary results of major labour productivity monitoring programme.” Proc., 3rd Yugoslavian Symp. Constr. Mgmt., Cavtat, 18–28.
Hyde, R. (1995). “Buildability as a design concept for architects: A case study of laboratory buildings.” Eng. Construct. Architect. Manag., 2(1), 45–56.
Illingworth, J. R. (2000). Construction methods and planning, 2nd Ed., Taylor & Francis, London.
Jarkas, A. M. (2005). “An investigation into the influence of buildability factors on productivity of in situ reinforced concrete construction.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of Dundee, Dundee, UK.
Jergeas, G., and Van der Put, J. (2001). “Benefits of constructability on construction projects.” J. Constr. Eng. Manage., 127(4), 281–290.
Kim, J-O., and Ferree, G. D., Jr. (1981). “Standardization in causal analysis.” Sociol. Methods Res., 10(2), 187–210.
Lal, H. (1999). “The use of characteristic productivity modelling in the improvement of site performance and the evaluation of delay and disruption claims.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of Dundee, Dundee, UK.
Lam, P. T. I., Chan, A. P. C., Wong, F. K. W., and Wong, F. W. H. (2007). “Constructability rankings of construction systems based on the analytical hierarchy process.” J. Archit. Eng., 13(1), 36–43.
Lam, P. T. I., and Wong, F. W. H. (2009). “Improving building project performance: How buildability benchmarking can help.” Constr. Manage. Econ., 27(1), 41–52.
McTague, B., and Jergeas, G. (2002). “Productivity improvements on Alberta major construction projects: Phase I—back to basics.” Alberta Economic Development, Alberta, Canada.
Moore, D. (1996a). “Buildability, prefabrication, rationalization and passive buildings in the UK.” Proc., Association of Researchers in Construction Management, 12th Annual Conf. and Annual General Meeting, Vol. 1, A. Thorp, ed., ARCOM, Brighton, UK, 93–100.
Moore, D. (1996b). “Buildability assessment and the development of an automated design aid for managing the transfer of construction process knowledge.” Eng. Construct. Architect. Manag., 3(1/2), 29–46.
Nima, M. A., Abdul-Kadir, M. R., Jaafar, M. S., and Alghulami, R. G. (2002). “Constructability concepts in west port highway in Malaysia.” J. Constr. Eng. Manage., 128(4), 348–356.
Noor, I. (1992). “A study of the variability of labour productivity in building trades.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of Dundee, Dundee, UK.
O’Connor, J. T., and Davis, V. S. (1988). “Constructability improvement during field operations.” J. Constr. Eng. Manage., 114(4), 548–564.
O’Connor, J. T., Larimore, M. A., and Tucker, R. L. (1986). “Collecting constructability improvement ideas.” J. Constr. Eng. Manage., 112(4), 463–475.
O’Connor, J. T., Rusch, S. E., and Schulz, M. J. (1987). “Constructability concepts for engineering and procurement.” J. Constr. Eng. Manage., 113(2), 235–248.
Poh, P. S. H., and Chen, J. (1998). “The Singapore buildable design appraisal system: A preliminary review of the relationship between buildability, site productivity and cost.” Constr. Manage. Econ., 16(6), 681–692.
Pulaski, M. H., and Horman, M. J. (2005). “Organizing constructability knowledge for design.” J. Constr. Eng. Manage., 131(8), 911–919.
Rakhra, A. S. (1991). “Construction productivity: Concept, measurement and trends, organisation and management in construction.” Proc. 4th Yugoslavian Symp. on Constr. Mgmt., Dubrovnik, 487–497.
Royal Institution of Chartered Surveyors (RICS). (1979). “UK and US construction industries: A comparison of design and contract procedures,” RICS, Dept. of Construction Management, Univ. of Reading, Reading, UK, 50–92.
Saghatforoush, E., Hasim, S., Jaafar, M. S., and Kadir, M. R. A. (2009). “Constructability implementation among Malaysian building contractors.” Eur. J. Sci. Res., 29(4), 518–532.
Sincich, T. L., Levine, D. M., and Stephan, D. (2002). Practical statistics by example using Microsoft Excel and Minitab, 2nd Ed., Prentice Hall, Upper Saddle River, NJ.
Song, Y., and Chua, D. K. H. (2006). “Modeling of functional construction requirements for constructability analysis.” J. Constr. Eng. Manage., 132(12), 1314–1326.
Talhouni, B. T. K. (1990). “Measurement and analysis of construction labour productivity.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of Dundee, Dundee, UK.
Trigunarsyah, B. (2004). “Constructability practices among construction contractors in Indonesia.” J. Constr. Eng. Manage., 130(5), 656–669.
Trigunarsyah, B. (2007). “Project designers’ role in improving constructability of Indonesian construction projects.” Constr. Manage. Econ., 25(2), 207–215.
Tucker, R. L. (1986). “Management of construction productivity.” J. Manage. Eng., 2(3), 148–156.
Weisberg, S. (1985). “Applied linear regression.” 2nd Ed., Wiley, Hoboken, NJ.
Information & Authors
Information
Published In
Copyright
© 2012 American Society of Civil Engineers.
History
Received: Feb 27, 2010
Accepted: May 11, 2011
Published online: Feb 15, 2012
Published in print: Mar 1, 2012
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.