Monte Carlo Simulation of Shear Capacity of URM Walls Retrofitted by Polyurea Reinforced GFRP Grids
Publication: Journal of Composites for Construction
Volume 12, Issue 4
Abstract
A model proposed in the literature for the evaluation of the in-plane shear capacity of unstrengthened and strengthened concrete and clay brick unreinforced masonry (URM) walls was modified and calibrated following the results from an experimental research program. The tested walls were strengthened with grids made from glass fiber-reinforced polymer (GFRP) embedded within a rapid-setting sprayed polyurea. Various GFRP grid reinforced polyurea layouts were investigated, and consisted of strips oriented in either the vertical or horizontal direction and installed on one or both faces. The prediction models proposed in this paper were subsequently evaluated using a probabilistic Monte Carlo simulation (MCS) by considering the uncertainty and variability of the independent variables, which were assumed to follow a truncated normal distribution. Corroborated by the MCS, test results clearly show that the failure modes of the strengthened URM walls were affected by the strengthening scheme. Experimental and simulation results are presented and discussed in this paper.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This project was made possible by the financial support of the NSF Industry/University Cooperative Research Center on “Repair of Buildings and Bridges with Composites.” The contributions of its industrial members Bondo Corporation, Atlanta, Ga., and TechFab LLC, Anderson, S.C., are acknowledged.
References
Albert, M. L., Elwi, A. E., and Cheng, J. J. R. (2001), “Strengthening of unreinforced masonry walls using FRPs,” J. Compos. Constr., 5(2), 76–84.
American Society of Civil Engineers (ASCE). (2000). “Prestandard and commentary for the seismic rehabilitation of buildings.” Rep. No. FEMA-356, SAC Joint Venture Project, Federal Emergency Management Agency (FEMA), Washington, D.C.
Ang, A. H.-S., and Tang, W. H. (1975). Probability concepts in engineering planning and design—Volume I: Basic principles, Wiley, New York.
Ang, A. H.-S., and Tang, W. H. (1990). Probability concepts in engineering planning and design—Volume II: Decision, risk and reliability, Wiley, New York.
Building Seismic Safety Council (BSSC) of the National Institute of Building Sciences. (2004). “NEHRP recommended provisions for seismic regulations for new buildings and other structures.” Rep. No. FEMA-450, Federal Emergency Management Agency (FEMA), Washington, D.C.
Crisafulli, F. J., Carr, A. J., and Park, R. (1995). “Shear strength of unreinforced masonry panels.” Proc., Pacific Conf. on Earthquake Engineering, 77–86.
Ehsani, M. R., Saadatmanesh, H., and Al-Saidy, A. (1997), “Shear behavior of URM retrofitted with FRP overlays.” J. Compos. Constr., 1(1), 17–25.
Godinich, C. (2000). “Polyurea: A market overview.” J. European Coatings, 10(1), 54.
Li, T., Galati, N., Tumialan, J. G., and Nanni, A. (2005). “Analysis of unreinforced masonry concrete walls strengthened with glass fiber reinforced polymer bars.” ACI Struct. J., 102(4), 569–577.
Mann, W., and Müller, H. (1982). “Failure of shear-stressed masonry—An enlarged theory, tests and application to shear walls.” Proc., British Ceramic Society, 223–235.
The Masonry Society (TMS). (1994). Performance of masonry structures in the Northridge, California earthquake of January 17, 1994, R. E. Klingner, ed., Univ. of Texas at Austin, Austin, Tex.
Paulay, T., and Priestley, M. J. N. (1992). Seismic design of reinforced concrete and masonry buildings, Wiley, New York.
Polakowski, N. H., and Ripling, E. J. (1976). Strength and structure of engineering materials, Prentice-Hall, Englewood Cliffs, N.J.
Schneider, R. R., and Dickey, W. L. (1993). Reinforced masonry design, 3rd Ed., Prentice-Hall, Englewood Cliffs, N.J.
Secondin, S. (2003). Masonry reinforced with FRP system.” CIES Research Rep. No. 03-43, Univ. of Missouri, Rolla, Miss.
Triantafillou, T. C. (1998). “Strengthening of masonry structures using epoxy-bonded FRP laminates.” J. Compos. Constr., 2(2), 96–104.
Tumialan, G., Morbin, A., Nanni, A., and Medena, C. (2001). “Shear strength of masonry walls with FRP composites.” Proc., Composites 2001 Convention and Trade Show, 11.
Tumialan, J. G., Galati, N., and Nanni, A. (2003). “Fiber-reinforced polymer strengthening of unreinforced masonry walls subjected to out-of-plane loads.” ACI Struct. J., 100(3), 321–329.
Turek, M., Ventura, C. E., and Kuan, S. (2007). “In-plane shake-table testing of GFRP-strengthened concrete masonry walls.” Earthquake Spectra, 23(1), 223–237.
Valluzzi, M. R., Tinazzi, D., and Modena, C. (2002). “Shear behavior of masonry panels strengthened by FRP laminates.” Constr. Build. Mater., 16(7), 409–416.
Voon, K. C., and Ingham, J. M. (2006). “Experimental in-plane shear strength investigation of reinforced concrete masonry walls.” J. Struct. Eng., 132(3), 400–408.
Yamatsuka, K., and Siu, J. (2002). “2001 Nisqually earthquake: Lessons learned by the city of Seattle.” Proc., EERI Seventh U.S. National Conf. on Earthquake Engineering, 10.
Yu, P., Silva, P., and Nanni, A. (2007). “In-plane response of URM walls strengthened with GFRP grid reinforced polyurea.” Proc., 10th North American Masonry Conf., The Masonry Society (TMS), St. Louis, Mo., 12.
Zorapapel, G. T., Hart, G., and Frangopol, D. M. (1997). “Performance assessment of concrete masonry wall buildings using Monte Carlo simulation.” TMS J., 15(1), 59–66.
Information & Authors
Information
Published In
Copyright
© 2008 ASCE.
History
Received: Mar 9, 2007
Accepted: Sep 24, 2007
Published online: Aug 1, 2008
Published in print: Aug 2008
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.