Intermediate Crack Debonding in FRP-Strengthened RC Beams: FE Analysis and Strength Model
Publication: Journal of Composites for Construction
Volume 11, Issue 2
Abstract
Reinforced concrete (RC) beams strengthened in flexure with a bonded fiber-reinforced polymer (FRP) plate may fail by intermediate crack (IC) debonding, in which debonding initiates at a critical section in the high moment region and propagates to a plate end. This paper first presents a finite-element (FE) model based on the smeared crack approach for concrete for the numerical simulation of the IC debonding process. This finite-element model includes two novel features: (1) the interfacial behavior within the major flexural crack zone is differentiated from that outside this zone and (2) the effect of local slip concentrations near a flexural crack is captured using a dual local debonding criterion. The FE model is shown to be accurate through comparisons with the results of 42 beam tests. The paper also presents an accurate and simple strength model based on interfacial shear stress distributions from finite-element analyses. The new strength model is shown to be accurate through comparisons with the test results of 77 beams, including the 42 beams used in verifying the FE model, and is suitable for direct use in design.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers are grateful for the financial support received from The Hong Kong Polytechnic University through its Area of Strategic Development (ASD) Scheme for the ASD in Urban Hazard Mitigation and the Natural Science Foundation of China (National Key Project No. UNSPECIFIED50238030).
References
American Concrete Institute (ACI). (2002). “Guide for the design and construction of externally bonded FRP systems for strengthening concrete structures.” ACI 440.2R-02, ACI Committee 440, Detroit.
Aprile, A., Spacone, E., and Limkatanyu, S. (2001). “Role of bond in RC beams strengthened with steel and FRP plates.” J. Struct. Eng., 127(12), 1445–1452.
Arduini, M., Nanni, A., and Romagnolo, M. (2004). “Performance of one-way reinforced concrete slabs with externally bonded fiber-reinforced polymer strengthening.” ACI Struct. J., 101(2), 193–201.
Arduini, M., Tommaso, A. D., and Nanni, A. (1997). “Brittle failure in FRP plate and sheet bonded beams.” ACI Struct. J., 94(4), 363–370.
Beber, A. J., Filho, A. C., and Campagnolo, J. L. (2001). “CFRP in the strengthening of reinforced concrete beams.” Proc., Int. Conf. on FRP Composites in Civil Engineering, J. G. Teng, ed., Elsevier Science, Amsterdam, The Netherlands, 391–398.
Brena, S. F., Bramblett, R. M., Wood, S. L., and Kreger, M. E. (2003). “Increasing flexural capacity of reinforced concrete beams using carbon fiber-reinforced polymer composite.” ACI Struct. J., 100(1), 36–46.
Buyukozturk, O. (1977). “Nonlinear analysis of reinforced concrete structures.” Comput. Struct., 7, 149–156.
CEB-FIP. (1993). Model Code 90, Lausanne, Switzerland.
Ceroni, F., and Prota, A. (2001). “Experimental behavior of RC beams strengthened by FRP sheets.” Proc., Int. Conf. on Composites in Constructions, J. Figueiras, L. Juvandes, and R. Faria, eds., Balkema, Rotterdam, The Netherlands, 499–504.
Chan, T. K., and Niall, M. (2001). “Strengthening of one-way slabs using carbon fibre plates: The effect of preload.” CSE Research Bulletin No. 14, Nanyang Technology Univ., Singapore.
Chen, J. F., and Teng, J. G. (2001). “Anchorage strength models for FRP and steel plates bonded to concrete.” J. Struct. Eng., 127(7), 784–791.
Fang, T. Q. (2002). “Study on U-shaped sheet behavior of anti-debonding in the concrete beam reinforced flexurally with FRP.” Master's thesis, Tsinghua Univ., Tsinghua, China.
Ferretti, D., and Savoia, M. (2003). “Non-linear model of R/C tensile members strengthened by FRP-plates.” Eng. Fract. Mech., 70, 1069–1083.
fib. (2001). “Externally bonded FRP reinforcement for RC structures.” Bulletin No. 14.
Gao, B., Leung, W. H., Cheung, C. M., Kim, J. K., and Leung, C. K. Y. (2001). “Effects of adhesive properties on strengthening of concrete beams with composite strips.” Proc., Int. Conf. on FRP Composites in Civil Engineering, J. G. Teng, ed., Elsevier Science, Amsterdam, The Netherlands, 423–432.
Garden, H. N., and Hollaway, L. C. (1998). “An experimental study of the influence of plate end anchorage of carbon fibre composite plates used to strengthen reinforced concrete beams.” Compos. Struct., 42, 175–188.
GB-50010. (2002). “Code for design of concrete structures.” China Building Industry Press, Beijing.
Grace, N. F., Abdel-Sayed, G., and Ragheb, W. F. (2002). “Strengthening of concrete beams using innovative ductile fiber-reinforced polymer fabric.” ACI Struct. J., 99(5), 692–700.
Hognestad, E. (1951). “A study of combined bending and axial load in reinforced concrete members.” Bulletin Series No. 399, Bulletin No.1, Univ. of Illinois Engineering Experiment Station.
Japan Society of Civil Engineers (JSCE). (2001). “Recommendations for upgrading of concrete structures with use of continuous fiber sheets.” Concrete Engineering Series 41, Tokyo.
Kwak, H. G., and Filippou, F. C. (1990). “Finite-element analysis of reinforced concrete structures under monotonic load.” Research Rep. No. UCB/SEMM-90/14, 33-39, Dept. of Civil Engineering, Univ. of California at Berkeley, Berkeley, Calif.
Lu, X. Z., Teng, J. G., Ye, L. P., and Jiang, J. J. (2005a). “Bond-slip models for FRP sheets/plates bonded to concrete.” Eng. Struct., 27(6), 920–937.
Lu, X. Z., Ye, L. P., Teng, J. G., and Jiang, J. J. (2005b). “Meso-scale finite-element model for FRP sheets/plates externally boned to concrete.” Eng. Struct., 27(4), 564–575.
Monti, G., Renzelli, M., and Luciani, P. (2003). “FRP adhesion in uncracked and cracked concrete zones.” Proc., 6th Int. Symp. on FRP Reinforcement for Concrete Structures, World Scientific, Singapore, 183–192.
MSC.MARC. (2003). User’s manual, MSC Software Corporation.
Niu, H. D. (2002). “Interfacial fracture mechanisms and performance evaluation of RC structural system strengthened with FRP sheets.” Doctoral thesis, Ibaraki Univ., Ibaraki, Japan.
Oehler, D. J., Park, S. M., and Mohamed Ali, M. S. (2003). “A structural engineering approach to adhesive bonding longitudinal plates to RC beams and slabs.” Composites, Part A, 34(12), 887–897.
Rahimi, H., and Hutchinson, A. (2001). “Concrete beams strengthened with externally bonded FRP plates.” J. Compos. Constr., 5(1), 44–56.
Rots, J. G., Nauta, P., Kusters, M. A., and Blaauwendraad, J. (1985). “Smeared crack approach and fracture localization in concrete.” Heron, 30(1), 1–48.
Sato, Y. (2003). “Mechanical characteristics of the retrofitted members.” Technical Rep. of JCI Technical Committee on Retrofit Technology, 62–78.
Shin, Y. S., and Lee, C. (2003). “Flexural behavior of reinforced concrete beams strengthened with carbon fiber-reinforced polymer laminates at different levels of sustaining load.” ACI Struct. J., 100(2), 231–239.
Teng, J. G., Chen, J. F., Smith, S. T., and Lam, L. (2002). FRP-strengthened RC structures, Wiley, London.
Teng, J. G., Smith, S. T., Yao, J., and Chen, J. F. (2003). “Intermediate crack-induced debonding in RC beams and slabs.” Constr. Build. Mater., 17(6–7), 447–462.
Triantafillou, T. C., and Plevris, N. (1992). “Strengthening of RC beams with epoxy-bonded fibre-composite materials.” Mater. Struct., 25, 201–211.
Tumialan, G., Serra, P., Nanni, A., and Belarbi, A. (1999). “Concrete cover delamination in reinforced concrete beams strengthened with carbon fiber reinforced polymer sheets.” Proc., 4th Int. Symp. on Fiber Reinforced Polymer Reinforcement for Reinforced Concrete Structures, C. W. Dolan, S. H. Rizkalla, and A. Nanni, eds., Md., 725–735.
Walraven, J. B., and Reinhardt, H. W. (1981). “Theory and experiments on the mechanical behavior of cracks in plain and reinforced concrete subject to shear load.” Heron, 26(1).
Wong, S. Y., and Vecchio, F. J. (2003). “Towards modeling of reinforced concrete members with externally bonded fiber-reinforced polymer composites.” ACI Struct. J., 100(1), 47–55.
Wu, Z. S., and Niu, H. D. (2000). “Shear transfer along FRP-concrete interface in flexural members.” J. Mater., Concr. Struct. and Pavements, JSCE, 49(662), 231–245.
Wu, Z. S., and Yin, J. (2003). “Fracture behaviors of FRP-strengthened concrete structures.” Eng. Fract. Mech., 70, 1339–1355.
Xiong, G. J., Jiang, H., Huang, J. Z., Yang, J. Z., and Xie, H. C. (2001). “Behavior of concrete beams strengthened with hybrid carbon fiber-glass fiber sheets.” Proc., Int. Conf. on FRP Composites in Civil Engineering, J. G. Teng, ed., Elsevier Science, Amsterdam, The Netherlands, 407–414.
Yao, J., Teng, J. G., and Lam, L. (2005). “Experimental study on intermediate crack debonding in FRP-strengthened RC flexural members.” Adv. Struct. Eng., 8(4), 365–396.
Ye, L. P., Cui, W., and Yue, Q. R. (2001). “Analysis and calculation of flexural strength of RC members strengthened with CFRP sheet.” Building Structures, 35(3), 3–5 (in Chinese).
Yi, W. J., and Huang, H. M. (2001). “Experimental study on the flexural behavior of RC beams strengthened with CFRP laminates.” Proc., Int. Conf. on FRP Composites in Civil Engineering, J. G. Teng, ed., Elsevier Science, Amsterdam, The Netherlands, 399–406.
Yuan, H., Teng, J. G., Seracino, R., Wu, Z. S., and Yao, J. (2004). “Full range behavior of FRP-to-concrete bonded joints: A closed-form analytical solution.” Eng. Struct., 26(5), 553–564.
Zhao, M., Zhao, H. D., and Zhang, Y. (2002). “Experimental study on flexural RC members strengthened with CFRP fabrics.” Struct. Eng., 2, 52–58 (in Chinese).
Information & Authors
Information
Published In
Copyright
© 2007 ASCE.
History
Received: Jun 16, 2005
Accepted: Nov 16, 2005
Published online: Apr 1, 2007
Published in print: Apr 2007
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.