Static Cyclic Response of Masonry Walls Retrofitted with Fiber-Reinforced Polymers
Publication: Journal of Composites for Construction
Volume 11, Issue 1
Abstract
The behavior of seven one-half scale masonry specimens before and after retrofitting using fiber-reinforced polymer (FRP) is investigated. Four walls were built using one-half scale hollow clay masonry units and weak mortar to simulate walls built in central Europe in the mid-20th century. Three walls were first tested as unreinforced masonry walls; then, the seismically damaged specimens were retrofitted using FRPs. The fourth wall was directly upgraded after construction using FRP. Each specimen was retrofitted on the entire surface of a single side. All the specimens were tested under constant gravity load and incrementally increasing in-plane loading cycles. The tested specimens had two effective moment/shear ratio, namely, 0.5 and 0.7. The key parameter was the amount of FRP axial rigidity, which is defined as the amount of FRP reinforcement ratio times its modulus. The single-side retrofitting/upgrading significantly improved the lateral strength, stiffness, and energy dissipation of the test specimens. The increase in the lateral strength was proportional to the amount of FRP axial rigidity. However, using high amount of FRP axial rigidity led to very brittle failure. Finally, simple existing analytical models estimated the ultimate lateral strengths of the test specimens reasonably well.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The FRP provided by SIKA AG is gratefully acknowledged. The fabrication of the half-scale bricks by Morandi is acknowledged. Appreciation is also extended to Mr. Jorge Hegner, former graduate student at EPFL.
References
Abrams D., P., and Lynch J., M. (2001). “Flexural behavior of retrofitted masonry piers.” Korea Earthquake Engineering Research Center (KEERC)–Mid America Earthquake Center (MAE) Joint Seminar on Risk Mitigation for Regions of Moderate Seismicity, Urbana, Ill.
Abrams, D., and Shah, N. (1992). “Cyclic load testing of unreinforced masonry walls.” Rep. No. 92-26-10, Advanced Construction Technology Center, Newmark Civil Engineering Laboratory, Dept. of Civil Engineering, Univ. of Illinois at Urbana-Champaign, Urbana, Ill.
Applied Technology Council (ATC). (2000). “Prestandard and commentary for the seismic rehabilitation of buildings.” Publication, No. 356, Federal Emergency Management Agency, Washington, D.C.
Comite Euro-International du Béton. (1999). “Design of masonry structures.” Eurocode 6, Lausanne, Switzerland.
ElGawady, M., Lestuzzi, P., and Badoux, M. (2004a). “A review of conventional seismic retrofitting techniques for URM.” Proc., 13th Int. Brick and Block Masonry Conf., Amsterdam, The Netherlands, Paper No. 89.
ElGawady, M., Lestuzzi, P., and Badoux, M. (2004b). “A review of retrofitting of unreinforced masonry walls using composites.” Proc., 4th Int. Conf. on Advanced Composite Materials in Bridges and Structures, Calgary, Alta, Canada.
ElGawady, M., Lestuzzi, P., and Badoux, M. (2004c). “Static cyclic tests on URM wall before and after retrofitting with composites.” Proc., 13th Int. Brick and Block Masonry Conf., Amsterdam, The Netherlands, Paper No. 181.
ElGawady, M. A., Lestuzzi, P., and Badoux, M. (2005). “In-plane seismic response of URM walls upgraded with FRP.” J. Compos. Constr., 9(6), 524–535.
European Committee for Standardization. (1999a). “Methods of test for masonry. Determination of compressive strength.” EN 1052-1, CEN, Brussels, Belgium.
European Committee for Standardization. (1999b). “Methods of test for mortar for masonry. Determination of flexural and compressive strength of hardened mortar.” EN 1015–11, CEN, Brussels, Belgium.
European Committee for Standardization. “Methods of test for masonry units. Determination of compressive strength.” EN 772-1, CEN, Brussels, Belgium.
Holberg, M., and Hamilton, R. (2002). “Strengthening, URM with GFRP composites and ductile connections.” Earthquake Spectra, 18(1), 63–84.
ICBO Evaluation Service, Inc. (2001). “Acceptance criteria for concrete and reinforced and unreinforced masonry strengthened using fiber-reinforced polymers (FRP), composite systems.” AC125.
Magenes, G., and Calvi, G. M. (1997). “In-plane seismic response of brick masonry walls.” Earthquake Eng. Struct. Dyn., 26(11), 1091–1112.
Moon, F. (2004). “Seismic strengthening of low-rise unreinforced structures with flexible diaphragms.” Ph.D. dissertation, Georgia Institute of Technology.
Reinhorn, A. M., and Maden, A. (1995). “Evaluation of TYFO-W fiber wrap system for in plane strengthening of masonry walls.” Rep. No. 95-0002, Dept. of Civil Engineering, State Univ. of New York at Buffalo, Buffalo, N.Y.
Schwegler, G. (1994). “Masonry construction strengthened with fiber composites in seismically endangered zones.” 10th, ECEE., Vienna, 2299–2303.
Tomazevic, M. (1999). Earthquake-resistant design of masonry buildings, Imperial College Press, London.
Triantafillou, T. C. (1998). “Strengthening of masonry structures using epoxy-bonded FRP laminates.” J. Compos. Constr., 2(2), 96–104.
Zhao, T., Xie, J., and Li, H. (2003). “Strengthening of cracked concrete block masonry walls using continuous carbon fiber sheet.” 9th NAMC, Clemson, S.C., 156–167.
Information & Authors
Information
Published In
Copyright
© 2007 ASCE.
History
Received: Sep 20, 2005
Accepted: Mar 2, 2006
Published online: Feb 1, 2007
Published in print: Feb 2007
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.