Internal Shear Strength of Three Geosynthetic Clay Liners
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 124, Issue 10
Abstract
A study of the internal shear strength of adhesive-bonded, stitch-bonded, and needle-punched geosynthetic clay liners (GCLs) is presented. Tests were performed using a large direct shear machine capable of measuring peak and residual (or near residual) shear strengths. For each product, failure occurred at the woven geotextile/bentonite interface and excess pore pressures remained zero on the failure plane during shear. The peak shear strength of the needle-punched GCL increased significantly with increasing normal stress because of the frictional connection of the reinforcing fibers. The peak shear strengths of the adhesive-bonded and stitch-bonded GCLs showed smaller corresponding increases. The residual shear-strength failure envelope was essentially independent of product type. A two-stage procedure for specimen hydration is described, which reduced the required in-machine hydration time to reach equilibrium conditions. For the reinforced products, small decreases in peak and residual shear strengths were observed with decreasing displacement rate. The findings of the study have implications for the design of facilities incorporating GCLs and for the manufacturing and shear-strength testing of GCL products.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
ASTM. (1996). “Standard test method for direct shear test of soils under consolidated drained conditions.”Annual book of ASTM standards, ASTM D 3080, Vol. 04.08, ASTM, West Conshohocken, Pa., 295–300.
2.
ASTM. (1997). “Standard test method for grab breaking load and elongation of geotextiles.”Annual book of ASTM standards, ASTM D 4632, Vol. 04.09, ASTM, West Conshohocken, Pa., 972–975.
3.
Byrne, R. J. (1994). “Design issues with strain-softening interfaces in landfill liners.”Proc., Waste Tech. '94, Charleston, S.C., 1–26.
4.
Colloid Environmental Technologies Co. (CETCO). (1995). Bentomat/Claymax technical manual. CETCO, Arlington Heights, Ill.
5.
Daniel, D. E., Shan, H.-Y., and Anderson, J. D. (1993). “Effects of partial wetting on the performance of the bentonite component of a geosynthetic clay liner.”Proc., Geosynthetics '93, Vol. 3, Industrial Fabrics Assoc. Int., Roseville, Minn., 1483–1496.
6.
Fox, P. J.(1998). “Research on geosynthetic clay liners at Purdue University.”Geotech. News, Vancouver, Canada, 16(1), 35–40.
7.
Fox, P. J., Rowland, M. G., Scheithe, J. R., Davis, K. L., Supple, M. R., and Crow, C. C.(1997). “Design and evaluation of a large direct shear machine for geosynthetic clay liners.”Geotech. Testing J., 20(3), 279–288.
8.
Frobel, R. K.(1996). “Geosynthetic clay liners, part four: Interface and internal shear strength determination.”Geotech. Fabrics Rep., Industrial Fabrics Assoc. Int., Roseville, Minn., 14(8), 20–23.
9.
Fuller, J. M. (1995). “Landfill cap designs using geosynthetic clay liners.”Geosynthetic clay liners, R. M. Koerner, E. Gartung, and H. Zanzinger, eds., A. A. Balkema, Rotterdam, The Netherlands, 129–140.
10.
Gilbert, R. B., Fernandez, F., and Horsfield, D. W.(1996a). “Shear strength of reinforced geosynthetic clay liner.”J. Geotech. Engrg., ASCE, 122(4), 259–266.
11.
Gilbert, R. B., Long, J. H., and Moses, B. E.(1996b). “Analytical model of progressive slope failure in waste containment systems.”Int. J. for Numer. and Analytical Methods in Geomech., 20(1), 35–56.
12.
Gilbert, R. B., Scranton, H. B., and Daniel, D. E. (1997). “Shear strength testing for geosynthetic clay liners.”Testing and acceptance criteria for geosynthetic clay liners, STP 1308, L. W. Well, ed., ASTM, West Conshohocken, Pa., 121–135.
13.
Giroud, J. P., Darrasse, J., and Bachus, R. C.(1993). “Hyperbolic expression for soil-geosynthetic or geosynthetic-geosynthetic interface shear strength.”Geotextiles and Geomembranes, England, 12(3), 275–286.
14.
Heerten, G., Saathoff, F., Scheu, C., and von Maubeuge, K. P. (1995). “On the long-term shear behavior of geosynthetic clay liners (GCLs) in capping sealing systems.”Geosynthetic clay liners, R. M. Koerner, E. Gartung, and H. Zanzinger, eds., A. A. Balkema, Rotterdam, The Netherlands, 141–150.
15.
Ko, F. K. (1987). “Seaming and joining methods.”Geotextiles and Geomembranes, England, 6(1–3), 93–107.
16.
Koerner, R. M. (1997). “Perspectives on geosynthetic clay liners.”Testing and acceptance criteria for geosynthetic clay liners, STP 1308, L. W. Well, ed., ASTM, West Conshohocken, Pa., 3–20.
17.
Koerner, R. M., Carson, D. A., Daniel, D. E., and Bonaparte, R. (1996). “Current status of the Cincinnati GCL test plots.”Proc., GRI-10, Field Perf. of Geosynthetics and Geosynthetic Related Sys., Drexel University, Philadelphia, Pa., 147–175.
18.
Müller-Vonmoos, M., and Løken, T.(1989). “The shearing behavior of clays.”Appl. Clay Sci., Amsterdam, 4(2), 125–141.
19.
Richardson, G. N.(1997). “GCL internal shear strength requirements.”Geotech. Fabrics Rep., Industrial Fabrics Assoc. Int., Roseville, Minn., 15(2), 20–25.
20.
Rowland, M. G. (1997). “Research on the internal shear strength of three geosynthetic clay liners,” MS thesis, School of Civil Engineering, Purdue University, West Lafayette, Ind.
21.
Scheithe, J. R. (1996). “Research on the internal shear strength of a needle-punched geosynthetic clay liner,” MS thesis, School of Civil Engineering, Purdue University, West Lafayette, Ind.
22.
Schmitt, K. E., Bowders, J. J., Gilbert, R. B., and Daniel, D. E. (1997). “Enhanced shear strength of sodium bentonite using frictional additives.”Proc., Int. Containment Technol. Conf., Florida State Univ., Tallahassee, Fla, 355–361.
23.
Shan, H.-Y., and Daniel, D. E. (1991). “Results of laboratory tests on a geotextile/bentonite liner material.”Proc., Geosynthetics '91, Vol. 2, Industrial Fabrics Assoc. Int., Roseville, Minn., 517–535.
24.
Stark, T. D., and Eid, H. T.(1996). “Shear behavior of reinforced geosynthetic clay liners.”Geosynthetics Int., Industrial Fabrics Assoc. Int., Roseville, Minn., 3(6), 771–786.
25.
U.S. Environmental Protection Agency. (1996). “Report of 1995 workshop on geosynthetic clay liners.”Rep. No. EPA/600/R-96/149, Office of Research and Development, Washington, D.C.
Information & Authors
Information
Published In
Copyright
Copyright © 1998 American Society of Civil Engineers.
History
Published online: Oct 1, 1998
Published in print: Oct 1998
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.