Relaxation in High-Strength Bolted Connections Using Galvanized Steel
Publication: Journal of Bridge Engineering
Volume 5, Issue 2
Abstract
In recent bridge construction in Connecticut involving heavy sections, galvanized coating thicknesses were in excess of 12 mils. The current American Association of State Highway and Transportation Officials specification is based on research conducted with coating thicknesses not greater than 6 mils. Since thicker coatings on steel can reduce shear capacity in high-strength bolted connections, there was concern that the thick galvanized coating could compromise the performance. In this research, tests were conducted to study the relaxation and the shear capacity of high-strength bolted connections with galvanized coating thicknesses up to 20 mils. Both normal and oversize holes were studied. The research shows that the shear capacity of connections with thick galvanized coatings is reduced due to the loss in the clamping force. The test results have been used to develop design guidelines.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Bickford, J. H. (1990). An introduction to the design and behavior of bolted joints, 2nd Ed., Marcel Dekker, New York.
2.
Birkemore, P. C., and Herrschaft, D. C. ( 1970). “Bolted galvanized bridges: Engineering acceptance near.” Civ. Engrg., ASCE, 40(4), 42–46.
3.
Brookhart, G. C., Siddiqi, I. H., and Vasarhelyi, D. D. (1968). “Surface treatment of high strength bolted joints.”J. Struct. Div., ASCE, 94(3), 671–681.
4.
“Coefficient of friction of faying surfaces subjected to various corrosion protective treatments.” (1967). Rep. 2, Office of Research and Experiments of the International Union of Railways, Utrecht, The Netherlands.
5.
DeWolf, J. T., and Yang, J. (1998). “Relaxation in high-strength bolted connections using galvanized steel.” Final Rep. No. 97-4, Connecticut Department of Transportation, Rocky Hill, Conn.
6.
Donald, E. (1979). “Bleeding structures—The detection of fatigue in engineering elements.” Aircraft Engrg., 51(1), 25–29.
7.
Fisher, J. W., Struik, J. H., and Kulak, G. L. (1974). Guide to design criteria for bolted and riveted joints. Wiley, New York.
8.
Frank, K. H., and Yura, J. A. (1981). “An experimental study of bolted shear connections.” FHWA Final Rep. No. FHWA/RD-81/148, U.S. Department of Transportation/Federal Highway Administration, Washington, D.C.
9.
Lobb, V., and Stoller, F. (1971). “Bolted joints under sustained loadings.”J. Struct. Div., ASCE, 97(3), 905–933.
10.
Manual of steel construction: Load and resistance factor design. Volume I: Structural members, specifications and codes. Appendix A: Testing methods to determine the slip coefficients for coatings used in bolted joints, 2nd Ed. (1994). American Institute of Steel Construction, Chicago, Ill.
11.
Munse, W. H., and Birkemore, P. C. (1969). High-strength bolting of galvanized connections. The Australian Institute of Steel Construction and the Australian Coating Developmental Association, Sydney, Australia, and Melbourne.
12.
Nanninga, M. G. ( 1978). “Creep behavior of friction type joints with coated faying surfaces,” MS thesis, University of Texas at Austin.
13.
Specification for structural joints using ASTM A325 or A490 bolts. (1985). Research Council on Structural Connections, American Institute of Steel Construction, Chicago.
14.
Standard specification for highway bridges, 15th Ed. (1992). American Association of State Highway and Transportation Officials, Washington, D.C.
15.
Standard specification for zinc (hop-dip galvanized) coatings of iron and steel products. (1989). ASTM, West Conshohoken, Pa.
16.
Yang, J. ( 1997). “Relaxation in high strength bolted connections with galvanized steel,” MS thesis, University of Connecticut, Storrs, Conn.
17.
Yura, J. A., and Frank, K. H. (1985). “Testing method to determine the slip coefficient for coatings used in bolted joints.” Engrg. J., (third quarter), 151–155.
18.
Yura, J. A., Frank, K. H., and Cayes, L. (1981). “Friction-type bolted connections with A588 weathering steel.” FHWA Final Rep. No. FHWA/RD-812/147, U.S. Department of Transportation/Federal Highway Administration, Washington, D.C.
Information & Authors
Information
Published In
History
Received: Jun 12, 1998
Published online: May 1, 2000
Published in print: May 2000
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.