Design and Construction Practices that Affect Diaphragm Strength and Stiffness of Postframe Buildings
Publication: Practice Periodical on Structural Design and Construction
Volume 12, Issue 3
Abstract
Including diaphragm action in sizing building posts (columns) and postembedment depths (foundation) is more consistent with the actual building performance. A large portion of in-plane loading, such as wind, is transferred to the end walls through in-plane shear via metal roofing—a phenomenon called “diaphragm action.” Because of load sharing and redundancies that are not accounted for, postframe buildings are stronger and stiffer than what is normally assumed. Various construction and design practices that increase diaphragm strength and stiffness of postframe buildings are discussed. The objective of this paper is to discuss design and construction practices that contribute to the diaphragm strength and stiffness of metal-clad postframe rectangular buildings. The paper is based on data and information obtained from the full-scale metal-clad timber-framed postframe building tested over a period of 9 years, and the literature. Understanding the functions, contributions, interactions, and load sharing characteristics of the different framing, cladding, and redundant elements is critical in understanding the diaphragm action and optimizing designs of postframe buildings. The study benefits the engineers, architects, builders, and code officials of postframe buildings.
Get full access to this article
View all available purchase options and get full access to this article.
References
Alumax Building Products. (1992). “Power panel test data for postframe end walls with diaphragm loading.” Alumax Building Products, Reidsville, N.C.
Anderson, G. A. (1987). “Evaluation of a light-gage metal diaphragm behavior and the diaphragm interaction with post frames.” Doctoral dissertation, Iowa State Univ., Ames, Iowa.
Anderson, G. A. (1990). “What affects the strength and stiffness of diaphragms?” ASAE Paper No. 90-4028, ASABE, St. Joseph, Mich.
Anderson, G. A. (1991). “Lumber-framed metal-clad wall diaphragm test results.” ASAE Paper No. 91-4057, ASABE, St. Joseph, Mich.
Anderson, G. A., and Bundy, D. S. (1989). “Characterizing diaphragm shear stiffness for diaphragm-frame interaction analysis.” Trans. ASAE, 32(5), 1785–1790.
ASAE Standards. (1990). “EP484.1 Diaphragm design of metal-clad postframe rectangular buildings.” ASAE standards, 48th Ed., ASABE, St. Joseph, Mich.
ASAE Standards. (2001a). “EP484.2 Diaphragm design of metal-clad, postframe rectangular buildings.” ASAE Standards, 48th Ed., ASABE, St. Joseph, Mich.
ASAE Standards. (2001b). “EP486.1 Shallow post foundation design.” ASAE Standards, 48th Ed., ASABE, ST. Joseph, Mich.
Bohnhoff, D. (1989). “Influence of insulation on the behavior of metal-clad wood-frame diaphragms.” ASAE Paper No. 89-4507, ASABE, St. Joseph, Mich.
Bohnhoff, D. (1992). “Expanding diaphragm analyses for postframe buildings.” Appl. Eng. Agric., 8(4), 509–517.
Bohnhoff, D. (2002). “Post foundation design considerations.” Wood Des. Focus, 12(3), 10–16.
Gebremedhin, K. G. (1994). “Design of bracing systems for end walls with doors.” Frame Building News, 6(4), 64–70.
Gebremedhin, K. G. (2002). “Testing a full-scale building after in service.” Wood Des. Focus, 12(3), 20–23.
Gebremedhin, K. G., Bartsch, J. A., and Jorgensen, M. C. (1992a). “Predicting roof diaphragms and end-wall stiffness from full-scale test results of a metal-clad, postframe building.” Trans. ASAE, 35(3), 977–985.
Gebremedhin, K. G., Manbeck, H. B., and Bahler, E. L. (1992b). “Diaphragm analysis and design of postframe buildings.” Postframe Building Design, J. N. Walker and F. E. Woeste, eds., ASAE Monograph Number 11, ASABE, St. Joseph, Mich., 35–63.
Gebremedhin, K. G., and Irish, W. W. (1986). “Ultimate load-deflection characteristics and failure modes of ceiling diaphragms for farm buildings.” Wood Fiber Sci., 18(4), 565–578.
Gebremedhin, K. G., and Jorgensen, M. C. (1993). “Stiffness of postframe building end walls.” Trans. ASAE, 36(3), 905–913.
Gebremedhin, K. G., and Price, J. (1999). “Tests of postframe building diaphragm.” J. Struct. Eng., 125(10), 1170–1178.
Gebremedhin, K. G., and Woeste, F. E. (1986). “Diaphragm design with knee brace slip for postframe buildings.” Trans. ASAE, 29(2), 538–542.
Geisthardt, A. C., Siegel, C., and Shirek, L. (1991). “Research and development: An industry perspective.” Proc., Presented at the ASAE Winter Meeting, December 17–20 1991, Chicago.
Hausmann, C. T., and Esmay, M. L. (1975). “Pole barn wind resistance design using diaphragm action.” ASAE Paper No. 75-4035, ASABE, St. Joseph, Mich.
Hoagland, R. C., and Bundy, D. S. (1983). “Postframe design using diaphragm theory.” Trans. ASAE, 26(5), 1499–1503.
Johnston, R. A., and Curtis, J. O. (1984). “Experimental verification of stressed-skin design of pole-frame buildings.” Trans. ASAE, 27(1), 159–164.
Luttrell, L. D. (1965). “Structural performance of light gauge steel diaphragms.” Rep. No. 319, Dept. of Structural Engineering, Cornell Univ., Ithaca, N.Y., 105.
McFadden, V. J., Bundy, D. S., and Lukens, A. (1991). “Evaluation of the wind loading of a postframe structure.” Trans. ASAE, 34(3), 1860–1865.
Niu, K. T. (1996). “A semiempirical three-dimensional stiffness model for metal-clad postframe buildings.” Ph.D. dissertation, Dept. of Biological and Environmental Engineering, Cornell Univ., Ithaca, N.Y.
Niu, K. T., and Gebremedhin, K. G. (1997a). “Three-dimensional building stiffness model for postframe buildings.” Trans. ASAE, 40(3), 795–801.
Niu, K. T., and Gebremedhin, K. G. (1997b). “Evaluation of interaction of wood framing and metal-cladding in roof diaphragms.” Trans. ASAE, 40(2), 465–476.
Riskowski, G. L. (1992). “Postframe building foundation design.” Wood Des. Focus, 3(1), 18–22.
Theilen, R., Bender, D. A., Pollock, D. G., and Winistorfer, S. (1997). “Lateral performance of ring-shank nails in Southern Pine lumber.” Frame Building News, 9(1), 62–71.
Truss Plate Institute (TPI). (1989). “Commentary and recommendations for handling, installing, and bracing metal-plate-connected wood trusses (DSB-89).” Madison, Wisc.
Truss Plate Institute (TPI). (1998). “Postframe summary sheet (HIB-98).” Madison, Wisc.
Truss Plate Institute (TPI). (1998).“Recommended design specification for temporary bracing of metal-plate-connected wood trusses (HIB-91).” Madison, Wisc.
Walker, J. N., and Woeste, F. E. (1992). “Postframe building design.” ASAE Monograph No. 11, ASABE, St. Joseph, Mich.
White, R. N., Hartand, J., and Warshaw, C. (1977). “Shear strength and stiffness of aluminum diaphragms in timber-framed buildings.” Research Rep. No. 370. Dept. of Structural Engineering, Cornell Univ., Ithaca, N.Y.
Wirt, D. L., Woeste, F. E., Kline, D. E., and McLain, T. E. (1992). “Design procedures for postframe end walls.” Appl. Eng. Agric., 8(1), 97–105.
Woeste, F. E., and Townsend, M. (1992). “Postframe end-wall diaphragm testing.” ASAE Paper No. 92-4540, ASABE, St. Joseph, Mich.
Information & Authors
Information
Published In
Practice Periodical on Structural Design and Construction
Volume 12 • Issue 3 • August 2007
Pages: 153 - 160
Copyright
© 2007 ASCE.
History
Received: May 25, 2006
Accepted: Oct 31, 2006
Published online: Aug 1, 2007
Published in print: Aug 2007
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.