Strength and Slake Durability of Lime Stabilized Pond Ash
Publication: Journal of Materials in Civil Engineering
Volume 19, Issue 7
Abstract
Pond ash, after adequate stabilization, may be suitable for various engineering applications. The effects of lime stabilization on the strength and durability aspects of a class F pond ash, with a lime constituent as low as 1.12%, are reported. Lime contents of 10 and 14% were used, and the samples were cured at ambient temperature of around for curing periods of 28, 45, 90, and . Samples were subjected to unconfined compression tests as well as tests that are usually applied to rocks such as point load strength tests, rebound hammer tests, and slake durability tests. Unconfined compressive strength (UCS) values of 4.8 and and slake durability indices of 98 and 99% were achieved after of curing for samples stabilized with 10 and 14% lime, respectively. Good correlations, that are particularly suitable for stabilized materials of low density and low strength, have been derived for strength parameters obtained from UCS tests, point load strength tests, and Schmidt rebound hammer tests, and also between UCS and slake durability index.
Get full access to this article
View all available purchase options and get full access to this article.
References
ASTM. (1992a). ASTM standards on soil stabilization with admixtures, 2nd Ed., Philadelphia.
ASTM. (1992b). “Standard test method for slake durability of shales and similar weak rocks.” D 4644-87(92), West Conshohocken, Pa.
ASTM. (1995a). “Standard test method for determination of the point load strength index of rock.” D 5731-95, West Conshohocken, Pa.
ASTM. (1995b). “Standard test method for determination of rock hardness by rebound hammer method.” D 5873-95, ASTM, West Conshohocken, Pa.
Bureau of Indian Standards. (1987). “Compendium of Indian standards on soil engineering. Part I.” New Delhi, India.
Chand, S. K. (2003). “Lime stabilization of pond ash by in-place and mixing methods: Geoenvironmental and strength considerations.” Ph.D. thesis, Indian Institute of Technology, Kharagpur, India.
Franklin, J. A. (1981). “A shale rating system and tentative applications to shale performance.” Transportation Research Record. 790, Transportation Research Board, Washington, D.C., 2–12.
Franklin, J. A., and Dusseault, M. B. (1989). Rock engineering, McGraw-Hill, New York
Ghosh, A. (1996). “Environmental and engineering characteristics of stabilized low lime fly ash.” Ph.D. thesis, Indian Institute of Technology, Kharagpur, India.
Ghosh, A., and Subbarao, C. (1998). “Hydraulic conductivity and leachate characteristics of stabilized fly ash.” J. Environ. Eng., 124(9), 812–820.
Ghosh, A., and Subbarao, C. (2001). “Microstructural development in fly ash modified with lime and gypsum.” J. Mater. Civ. Eng., 13(1), 65–70.
Ghosh, A., and Subbarao, C. (2006). “Tensile strength bearing ratio and slake durability of Class F fly ash stabilized with lime and gypsum.” J. Mater. Civ. Eng., 18(1), 18–27.
Goodman, R. E. (1989). Introduction to rock mechanics, 2nd Ed., Wiley, New York
Grasso, P., Xu, S., and Mahtab, A. (1992). “Problems and promises of index testing of rocks.” Proc., 33rd U.S. Symp. on Rock Mechanics, Tillerson, J. R. and Wawersik, W. R., eds., Balkema, Rotterdam, The Netherlands, 879–888.
Haramy, K. Y., and DeMarco, M. J. (1985). “Use of the Schmidt hammer for rock and coal testing.” Proc., 26th U.S. Symp. on Rock Mechanics, E. Ashworth, ed., 549–555.
Hudson, J. A., and Harrison, J. P. (1997). Engineering rock mechanics, Pergamon, Elsevier Science, Oxford, U.K.
Joshi, R. C., Duncan, D. M., and McMaster, M. (1975). “New and conventional engineering uses of fly ash.” J. Transp. Eng., 101(TE 4), 791–806.
Lovell, C. W. (1983). “Standard laboratory testing for compacted shales.” Proc., ISRM International Congress on Rock Mechanics, Vol. 1, A197–A202.
Malhotra, V. M. (1994). Fly ash in concrete, 2nd. Ed., CANMET Publication on Concrete, Ottawa, Canada.
Rusch, K. A., Guo, T., and Seals, R. K. (2002). “Stabilization of phosphogypsum using class C fly ash and lime: Assessment of the potential for marine applications.” J. Hazard. Mater., B93, 167–186.
Soliman, N. N. (1990). “Laboratory testing of lime fixed fly ash and FGD sludge.” Geotechnics of waste fills—Theory and practice, ASTM STP 1070, Landva, A. and Knowles, G. D. eds., American Society for Testing and Materials, Philadelphia, 168–183.
Subbarao, C., and Ghosh, A. (1997). “Fly ash management by stabilization.” J. Solid Waste Technol. Manage., 24(3), 126–130.
Usmen, M. A., and Moulton, L. K. (1984). “Construction and performance of experimental base course test sections built with waste calcium sulfate, lime, and fly ash.” Transportation Research Record. 998, Transportation Research Board, Washington, D.C., 52–62.
Information & Authors
Information
Published In
Copyright
© 2007 ASCE.
History
Received: Jun 22, 2005
Accepted: Feb 3, 2006
Published online: Jul 1, 2007
Published in print: Jul 2007
Notes
Note. Associate Editor: Kamran M. Nemati
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.