Impact Response of Steel Fiber-Reinforced Concrete Using a Split Hopkinson Pressure Bar
Publication: Journal of Materials in Civil Engineering
Volume 16, Issue 1
Abstract
The uniaxial compressive response of steel fiber-reinforced concrete (SFRC) subjected to high strain rate loading is presented. Details of an experimental investigation using a 75-mm-diameter split Hopkinson pressure bar (SHPB) are outlined. The investigation focuses on recorded data and results in distinguishing the strain rate that mobilizes ductility of steel fiber reinforced concrete. SFRC specimens with relatively high static compressive strength were tested at strain rates between about 20 and produced by impact from two specially designed striker bars on the SHPB facility; different impact load durations were produced using these striker bars. The reason for adopting this strategy is explained. Tests confirmed that the unconfined uniaxial compressive strength of SFRC increases with strain rate in the same way as plain concrete. Further, strain rate has a significant influence on the ductility of SFRC. At a high strain rate, the postpeak ductility is absent. This is in direct contrast to the behavior of the same material subjected to static loading. However, SFRC possesses good postpeak ductility at a strain rate below a specific value dictated by the entire loading process; a recommendation on the strain rate is proposed. A method for conducting approximate constant strain rate testing using the SHPB facility is also described in the paper.
Get full access to this article
View all available purchase options and get full access to this article.
References
Banthia, N., Mindess, S., and Trottier, J. F.(1996). “Impact resistance of steel fiber reinforced concrete.” ACI Mater. J., 93(5), 472–479.
Bischoff, P. H., and Perry, S. H. (1985). “Compressive strain rate effects of concrete.” Proc., Cement-Based Composites: Strain Rate Effects on Fracture, S. Mindess and S. P. Shah, eds., Materials Research Society, Warrendale, Pa., 64, 151–165.
Davies, R. M.(1948). “A critical study of the Hopkinson pressure bar.” Philos. Trans. A, 240, 375–457.
Follansbee, P. S., and Frantz, C.(1983). “Wave propagation in the split Hopkinson pressure bar.” J. Eng. Mater. Technol., 105, 61–66.
Gong, J. C., Malvern, L. E., and Jenkins, D. A.(1990). “Dispersion investigation in the split Hopkinson pressure bar.” J. Eng. Mater. Technol., 112, 309–314.
Kolsky, H.(1949). “An investigation of the mechanical properties of materials at very high rate of loading.” Proc. Phys. Soc. London, Sect. B, 62, 676–701.
Lindholm, U. S. (1971). “High strain rate tests.” Measurement of mechanical properties, Vol. 5, R. F. Bunshah, ed., Interscience, New York, 199–216.
Lok, T. S., Li, X. B., Liu, D. S., and Zhao, P. J.(2002). “Testing and response of large diameter brittle materials subjected to high strain rate.” J. Mater. Civ. Eng., 14(3), 262–269.
Lok, T. S., Zhao, P. J., Li, X. B., Liu, D. S., and Lim, C. H. (2001). “Effect of shaped impactor on the loading waveform in a large diameter split Hopkinson pressure bar.” Proc., 10th Int. Symp. on Interaction of the Effects of Munitions with Structures (CD-ROM), Defense Threat Reduction Agency, Fort Belvoir, Va.
Malvern, L. E., Tang, T., Jenkins, D. A., and Gong, J. C. (1985). “Dynamic compressive strength of cementitious materials.” Proc., Cement-Based Composites: Strain Rate Effects on Fracture, S. Mindess and S. P. Shah, eds., Materials Research Society, Warrendale, Pa., 64, 119–138.
Mansur, M. A., Chin, M. S., and Wee, T. H.(1999). “Stress-strain relationship of high-strength fiber concrete in compression.” J. Mater. Civ. Eng., 11(1), 21–29.
Ross, C. A., Tedesco, J. W., and Kuennen, S. T.(1995). “Effects of strain rate on concrete strength.” ACI Mater. J., 92(1), 37–47.
Shah, S. P., Stroeven, P., Dalhuisen, D., and Van Stekelenburg, P. (1978). “Complete stress-strain curves for steel fibre reinforced concrete in uniaxial tension and compression.” Proc., RILEM Symp. on Testing and Test Methods of Fibre Cement Composites, Construction Press, Lancaster, 399–408.
Taerwe, L., and Van-Gysel, A.(1996). “Influence of steel fibers on design stress-strain curve for high-strength concrete.” J. Eng. Mech., 122(8), 695–704.
Tang, T. X., Malvern, L. E., and Jenkins, D. A.(1992). “Rate effects in uniaxial dynamic compression of concrete.” J. Eng. Mech., 118(1), 108–124.
Williamson, G. R. (1974). The effect of steel fibers on the compressive strength of concrete, American Concrete Institute, Detroit, 195–207.
Zhao, H., and Gary, G.(1996). “On the use of SHPB techniques to determine the dynamic behavior of materials in the range of small strains.” Int. J. Solids Struct., 33(23), 3363–3375.
Zhao, P. J., Lok, T. S., Li, X. B., and Lim, C. H. (2001). “Behaviour of steel fibre reinforced concrete under dynamic load.” Proc., 4th Asia-Pacific Conf. on Shock and Impact Loads on Structures, T. S. Lok et al., eds., CI-Premier, Singapore, 573–580.
Information & Authors
Information
Published In
Copyright
Copyright © 2004 American Society of Civil Engineers.
History
Received: Jul 10, 2002
Accepted: Feb 12, 2003
Published online: Jan 16, 2004
Published in print: Feb 2004
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.