Thermal and Fatigue Behavior of Polymer Concrete Overlaid Beams
Publication: Journal of Materials in Civil Engineering
Volume 5, Issue 4
Abstract
Polymer concrete (PC) has been widely used for floor and bridge overlays, but because of the differences in the coefficients of thermal expansion between Portland‐cement concrete (PCC) and PC, there is concern about possible delamination at the interface. This paper is a report of the results of two experimental studies. The first was an investigation of crack propagation, stiffness deterioration, and delamination of PC‐PCC composite members subjected to load cycles at room temperature. The second was an investigation of the interface shear stresses and longitudinal normal stresses of PC‐PCC beams under various uniform thermal loads ranging from approximately 3°F (16°C) to 140°F (60°C). A hypothesis of the thermal phase was that interface shear stresses are localized near the ends of the beams. It was observed that: (1) Test beams survived 2,000,000 load cycles without delamination and without significant loss of stiffness; (2) interface shear stresses are end bound; and (3) the effective length of the end zone in which shear stresses are concentrated is approximately equal to the depth of the composite member.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Al‐Negheimish, A. I. (1988). “Bond strength, long term performance and temperature induced stresses in polymer concrete‐Portland cement concrete composite members,” PhD thesis, The University of Texas at Austin, Austin, Tex.
2.
Batchelor, B. D., Hewitt, B. E., and Csagoly, P. (1978). “An introduction of the fatigue strength of deck slabs of composite steel/concrete bridges.” Transp. Res. Record No. 664, Transp. Res. Board, Washington, D.C., 153–161.
3.
Birkeland, H. W. (1960). “Different shrinkage in composite beams.” J. Am. Concrete Inst., 56(11), 1123–1136.
4.
Chang, T. S., and Kesler, C. E. (1958). “Fatigue behavior of reinforced concrete beams.” Proc., American Concrete Inst., 55, 245–254.
5.
Chang, T. S., and Kesler, C. E. (1958). “Static and fatigue strength of beams with tensile reinforcement.” Proc., American Concrete Inst., 54, 1033–1058.
6.
Chen, D., Cheng, S., and Gerhardt, T. D. (1982). “Thermal stresses in laminated beams.” J. Thermal Stresses, 5(1), 67–84.
7.
Furr, H. L., and Ingram, L. L. (1971). “Bonding and durability of concrete and resinous overlays.” Research rep. 130‐5, Texas Transp. Inst., Texas A & M Univ., College Station, Tex.
8.
Grimado, P. B. (1978). “Interlaminar thermoelastic stresses in layered beams.” J. Thermal Stresses, 1(1), 75–86.
9.
Hess, M. (1969). “The end problem for a laminated elastic strip—II. differential expansion stresses.” J. Composite Mat., 3, 630–641.
10.
Kampf, L. (1968). “Repair of concrete bridge pavements.” Epoxies with concrete, SP‐21, Am. Concrete Inst., Detroit, Mich., 53–66.
11.
McConnell, W. R. (1968). “Epoxy surface treatments for portland cement concrete pavement.” Epoxies with Concrete, SP‐21, Am. Concrete Inst., Detroit, Mich., 9–17.
12.
Moffatt, K. R., and Dowling, P. J. (1984). “Interface shear stresses in composite plates under wheel loads.” The Struct. Engr., 62B(1), 1–5.
13.
Norby, G. M. (1958). “Fatigue of concrete—a review of research.” Proc., American Concrete Inst., 55, 191–215.
14.
Reilley, K. T. (1986). “A laboratory study of the fatigue of bonded PCC overlays,” MS thesis, The University of Texas at Austin, Austin, Tex.
15.
Rooney, H. A. (1968). “Epoxies in concrete construction and maintenance.” Epoxies with concrete, SP‐21, Concrete Inst., Detroit, Mich., 5–8.
16.
Silfwerbrand, J. (1986). “Bonding between old and new concrete in structures loaded by static and time‐dependent load.” Adhesion between polymers and concrete, H. R. Sasse, ed., Chapman and Hall Ltd., New York, N.Y., 309–319.
17.
“Specification for deformed and plain billet‐steel bars for concrete reinforcement.” Standard no. 01.04 (A615‐85), ASTM, Philadelphia, Pa.
18.
Standard Specification of Highway Bridges. (1983). 13th Ed., Am. Assoc. of State Hwy. and Transp. Officials, Washington, D.C.
19.
“Test Method for Static Modulus of Elasticity and Poisson's Ratio of Concrete in Compression.” Standard no. 04.02 (C469‐83), ASTM, Philadelphia, Pa.
20.
Timoshenko, S. P. (1925). “Analysis of bi‐metal thermostats.” J. Optical Soc. of Am., 11(3), 233–255.
21.
Whitesides, G. W. (1969). “Stresses in epoxy compounds for portland cement concrete.” Epoxies with Concrete, SP‐21, Concrete Inst., Detroit, Mich., 93–106.
22.
Zuk, W. (1961). “Thermal and shrinkage stresses in composite beams.” J. Am. Concrete Inst., 58(3), 327–340.
Information & Authors
Information
Published In
Copyright
Copyright © 1993 American Society of Civil Engineers.
History
Received: Feb 14, 1992
Published online: Nov 1, 1993
Published in print: Nov 1993
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.