Estimation of Pavement‐Layer Moduli using Nonlinear Optimization Technique
Publication: Journal of Transportation Engineering
Volume 120, Issue 3
Abstract
Falling Weight Deflectometer (FWD) testing is used for nondestructive structural evaluation of existing pavements. The deflection data from FWD can be used for estimation of layer moduli by an iterative technique. In the calculation process, commonly known as backcalculation, comparison is done between calculated deflections from a suitable theory and those measured by the FWD. The estimated moduli values correspond to the best fit of the measured deflection basin. In the present study, a nonlinear optimization technique has been used to estimate the layer moduli in the backcalculation process. The backcalculation scheme developed is applicable to 3‐layer to 6‐layer pavements. The method was verified by simulated deflection data from elastic‐layer theory and FWD‐deflection measurements on 13 in‐service pavements in Arizona. They were found to approximate closely the manual approach of matching deflection basins. The algorithm has been coded in a computer program called the Arizona Deflection Analysis Method (ADAM).
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Bergen, A. T., and Monismith, C. L. (1972). “Some fatigue considerations in the design of asphalt pavements.” Proc., Can. Tech. Asphalt Assoc., Vol. 17, Polyscience Publishers, Quebec, Canada.
2.
Bush, A. J. III. (1980). Non‐destructive testing of light aircraft pavements, phase‐II, development of the non‐destructive evaluation methodology. Final Rep. No. FAA‐RD‐80‐9‐11, Federal Aviation Administration (FAA), Washington, D.C.
3.
Gill, P. E., Murray, W., and Wright, M. H. (1981). Practical Optimization. Academic Press, New York, N.Y.
4.
Guide for design of pavement structures. (1986). American Association of State Highway and Transportation Officials (AASHTO), Washington, D.C.
5.
Hoffman, M. S., and Thompson, M. R. (1982). “A comparative study of selected non‐destructive testing devices.” Transp. Res. Record No. 852, Transportation Research Board (TRB), Washington, D.C., 32–42.
6.
Hossain, M. (1990). Deflection analysis of flexible pavements using non‐destructive test data, PhD thesis, Arizona State University, Tempe, Ariz.
7.
Hossain, M., and Zaniewski, J. P. (1991). “Detection and determination of depth and rigid bottom from falling weight deflectometer data.” Transp. Res. Record No. 1291, Transportation Research Board (TRB), Washington, D.C.
8.
Hveem, F. F. (1955). “Pavement deflections and fatigue failures.” Hwy. Res. Board Bull. 114, Highway Research Board, Washington, D.C.
9.
Lee, S. W., Mahoney, J. P., and Jackson, N. C. (1988). “A verification of backcalculation of pavement moduli.” Transp. Res. Record 1196, Transportation Research Board, Washington, D.C.
10.
Lister, N. W., and Kennedy, C. K. (1977). “A system for prediction of pavement life and design of pavement strengthening.” Proc., 4th Intl. Conf. on Struct. Des. of Asphalt Pavements, Vol. 1, University of Michigan, Ann Arbor, Mich., 629–648.
11.
Majidzadeh, K., and Ilves, G. (1981a). “Flexible pavement overlay design procedures, Vol. I.” Rep. No. FHWA/RD‐81/032, Federal Highway Administration, McLean, Va.
12.
Majidzadeh, K., and Ilves, G. (1981b). “Flexible pavement overlay design procedures, Vol. II.” Rep. No. FHWA/RD‐81/033, Federal Highway Administration, McLean, Va.
13.
Mamlouk, M. S., Houston, W. N., Houston, S. L., and Zaniewski, J. P. (1988). “Rational characterization of pavement structures using deflection analysis.” Rep. No. FHWA‐AZ88‐254, Vol. 1, Arizona Dept. of Transp., Phoenix, Ariz.
14.
Michelow, J. (1963). Analysis of stresses and displacements in an N‐layered elastic system under a uniformly distributed load on a circular area. California Research Corporation, Richmond, California.
15.
Painter, L. J. (1980). CHEVRON N‐layer program—improved accuracy. California Research Corporation, Richmond, California.
16.
Rajan, S. D. (1986). “A hybrid nonlinear programming method for design optimization.” J. Struct. Mech., 14(4), 455–474.
17.
Tholen, O., Sharma, J., and Terrel, R. L. (1982). “Comparison of falling weight deflectometer with other deflection testing devices.” Transp. Res. Record 1007, Transportation Research Board (TRB), Washington, D.C., 20–26.
18.
Uddin, W., Meyer, A. H., Hudson, W. R., and Stokoe, K. H. II. (1985). A structural evaluation methodology for pavements based on dynamic deflections. Res. Rep. No. 387‐1, Ctr. for Transp. Res., University of Texas, Austin, Tex.
19.
Ulliditz, P. (1987). Pavement Analysis. Elsevier, New York, N.Y.
20.
Uzan, J., Scullion, T., Michalek, C. H., Panedes, M., and Lytton, R. L. (1988). “A microcomputer based procedure of backcalculating layer moduli from FWD data.” Res. Rep. No. 1123, Texas Transportation Institute, Texas A&M University, College Station, Tex.
21.
Vanderplaats, G. N. (1973). CONMIN—a FORTRAN program for constrained function minimization: user's manual, NASA TMX‐62282, Ames Research Center and U.S. Army Air Mobility R&D Laboratory, Moffetfield, Calif.
22.
Zaniewski, J. P., Hudson, W. R., Seeds, S. B., and Moser, L. (1984). “Pavement performance model development.” Rep. No. FHWA/RD‐84/103, Vol. 2, ARE Inc., Austin, Tex.
Information & Authors
Information
Published In
Copyright
Copyright © 1994 American Society of Civil Engineers.
History
Received: Dec 19, 1990
Published online: May 1, 1994
Published in print: May 1994
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.