Reconsideration of Seismic Performance and Design of Beam-Column Joints of Earthquake-Resistant Reinforced Concrete Frames
Publication: Journal of Structural Engineering
Volume 135, Issue 7
Abstract
Seismic performance requirements for beam-column joints of earthquake-resistant reinforced concrete (RC) frames are discussed, and the experimental data of RC joints under cyclic loading collected from the literature are analyzed. It is observed that joint shear failure under cyclic loading is characterized by significant inelastic joint shear deformation. Joint shear strength should thus be formulated by limiting the influence of joint shear deformation on the seismic performance of RC frames. It is noticed that joint transverse reinforcement does not have significant influence on joint shear deformation and bond deterioration in the joints but may have significant influence on joint axial capacity under cyclic loading. Hence, the requirement for joint transverse reinforcement may be formulated by keeping the joint axial capacity not lower than the column axial capacity under seismic action. The influence of bond deterioration in joints on the seismic performance of RC frames and the anchorage requirement for beam reinforcement in joints are analyzed and discussed.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writer is grateful to Professor Susanto Teng (the writer’s supervisor), Professor Tso-Chien Pan, and Professor Chee-Kiong Soh, Nanyang Technological University, Singapore, for their guidance and help during the writer’s Ph.D. research.
References
Alameddine, F., and Ehsani, M. R. (1991). “High-strength RC connections subjected to inelastic cyclic loading.” J. Struct. Eng., 117(3), 829–849.
American Concrete Institute (ACI) Committee 318. (2002). Building code requirements for structural concrete (ACI 318–02) and commentary (318R-02), Farmington Hills, Mich.
American Concrete Institute (ACI) ASCE Committee 352. (2002). Recommendations for design of beam-column joints in monolithic concrete structures (ACI 352R-02), Farmington Hills, Mich.
Attaalla, S. A. (2004). “General analytical model for nominal shear stress of Type 2 normal- and high-strength concrete beam-column joints.” ACI Struct. J., 101(1), 65–75.
Bonacci, J., and Pantazopoulou, S. (1993). “Parametric investigation of joint mechanics.” ACI Struct. J., 90(1), 61–71.
Chen, C. C., and Chen, G. K. (1999). “Cyclic behavior of reinforced concrete eccentric beam-column corner joints connecting spread-ended beams.” ACI Struct. J., 96(3), 443–449.
Cheung, P. C., Paulay, T., and Park, R. (1991). “New Zealand tests on full scale reinforced concrete beam-column-slab subassemblages designed for earthquake resistance.” Design of beam-column joints for seismic resistance, SP-123, J. O. Jirsa, ed., American Concrete Institute, Farmington Hills, Mich., 1–37.
Durrani, A. J., and Wight, J. K. (1985). “Behavior of interior beam-to-column connections under earthquake-type loading.” ACI J., 82(3), 343–350.
Durrani, A. J., and Wight, J. K. (1987). “Earthquake resistance of reinforce concrete interior connections including a floor slab.” ACI Struct. J., 84(5), 400–406.
Ehsani, M. R., Moussa, A. E., and Vallenilla, C. R. (1987). “Comparison of inelastic behavior of reinforced ordinary- and high-strength concrete frames.” ACI Struct. J., 84(2), 161–169.
Ehsani, M. R., and Wight, J. K. (1985a). “Effect of transverse beams and slab on behavior of reinforced concrete beam-to-column connections.” ACI J., 82(2), 188–195.
Ehsani, M. R., and Wight, J. K. (1985b). “Exterior reinforced concrete beam-to-column connections subjected to earthquake-type loading.” ACI J., 82(4), 492–499.
Filippou, F. C., D’Ambrisi, A., and Issa, A. (1999) “Effect of reinforcement slip on hysteretic behavior of reinforced concrete frame members.” ACI Struct. J., 96(3), 327–335.
Fujii, S., and Morita, S. (1991). “Comparison between interior and exterior RC beam-column joint behavior.” Design of beam-column joints for seismic resistance, SP-123, J. O. Jirsa, ed., American Concrete Institute, Farmington Hills, Mich., 145–165.
Guimaraes, G. N., Kreger, M. E., and Jirsa, J. O. (1992). “Evaluation of joint-shear provisions for interior beam-column-slab connections using high-strength materials.” ACI Struct. J., 89(1), 89–98.
Hakuto, S., Park, R., and Tanaka, H. (1999). “Effect of deterioration of bond of beam bars passing through interior beam-column joints on flexural strength and ductility.” ACI Struct. J., 96(5), 858–864.
Hanson, N. W. (1971). “Seismic resistance of concrete frames with grade 60 reinforcement.” J. Struct. Div., 97(6), 1685–1700.
Hanson, N. W., and Connor, H. W. (1967). “Seismic resistance of reinforced concrete beam-column joints.” J. Struct. Div., 93(5), 533–560.
Hwang, S. J., Lee, H. J., Liao, T. F., Wang, K. C., and Tsai, H. H. (2005). “Role of hoops on shear strength of reinforced concrete beam-column joints.” ACI Struct. J., 102(3), 445–453.
Jirsa, J. O., ed. (1991). Design of beam-column joints for seismic resistance, SP-123, American Concrete Institute, Farmington Hills, Mich.
Joh, O., Goto, Y., and Shibata, T. (1991a). “Behavior of reinforced concrete beam-column joints with eccentricity.” Design of beam-column joints for seismic resistance, SP-123, J. O. Jirsa, ed., American Concrete Institute, Farmington Hills, Mich., 317–357.
Joh, O., Goto, Y., and Shibata, T. (1991b). “Influence of transverse joint and beam reinforcement and relocation of plastic hinge region on beam-column joint stiffness deterioration.” Design of beam-column joints for seismic resistance, SP-123, J. O. Jirsa, ed., American Concrete Institute, Farmington Hills, Mich., 187–223.
Kaku, T., and Asakusa, H. (1991). “Ductility estimation of exterior beam-column subassemblages in reinforced concrete frames.” Design of beam-column joints for seismic resistance, SP-123, J. O. Jirsa, ed., American Concrete Institute, Farmington Hills, Mich., 167–185.
Kitayama, K., Otani, S., and Aoyama, H. (1991). “Development of design criteria for RC interior beam-column joints.” Design of beam-column joints for seismic resistance, SP-123, J. O. Jirsa, ed., American Concrete Institute, Farmington Hills, Mich., 97–123.
Kurose, Y., Guimaraes, G. N., Liu, Z. H., Kreger, M. E., and Jirsa, J. O. (1991). “Evaluation of slab-beam-column connections subjected to bidirectional loading.” Design of beam-column joints for seismic resistance, SP-123, J. O. Jirsa, ed., American Concrete Institute, Farmington Hills, Mich., 39–67.
Leon, R. T. (1990). “Shear strength and hysteretic behavior of interior beam-column joints.” ACI Struct. J., 87(1), 3–11.
Mansour, M. Y., Lee, J. Y., and Hsu, T. T. C. (2001). “Cyclic stress-strain curve of concrete and steel bars in membrane elements.” J. Struct. Eng., 127(12), 1402–1411.
OES. (1995). “Vision 2000: Performance based seismic engineering of buildings.” Rep. Prepared by Structural Engineers Association of California, Sacramento, Calif.
Oka, K., and Shiohara, H. (1992). “Tests of high-strength concrete beam-column-joint subassemblages.” Proc., 10th World Conf. on Earthquake Eng., Taylor & Francis, Madrid, Spain, 3211–3217.
Pantazopoulou, S. J., and Bonacci, J. F. (1994). “On earthquake-resistant reinforced concrete frame connections.” Can. J. Civ. Eng., 21, 307–328.
Paulay, T., Park, R., and Priestley, M. J. N. (1978). “Reinforced concrete beam-column joints under seismic actions.” ACI J., 75(11), 585–593.
Rafflaelle, G. S., and Wight, J. K. (1995). “Reinforced concrete eccentric beam-column connections subjected to earthquake-type loading.” ACI Struct. J., 92(1), 45–55.
Shin, M., and LaFave, J. M. (2004). “Seismic performance of reinforced concrete eccentric beam-column connections with floor slabs.” ACI Struct. J., 101(3), 403–412.
Shiohara, H. (2001). “New model for shear failure of RC interior beam-column connections.” J. Struct. Eng., 127(2), 152–160.
Soleimani, D., Popov, E. P., and Bertero, V. V. (1979). “Hysteretic behavior of reinforced concrete beam-column subassemblages.” ACI J., 76(11), 1179–1195.
Standards Association of New Zealand. (1995). “Concrete structures standards (1995): Part 1—The design of concrete structures.” NZS 3101, Wellington, New Zealand.
Sugano, S., Nagashima, T., Kimura, H., and Ichikawa, A. (1991). “Behavior of beam-column joints using high-strength materials.” Design of beam-column joints for seismic resistance, SP-123, J. O. Jirsa, ed., American Concrete Institute, Farmington Hills, Mich., 359–377.
Teng, S., and Zhou, H. (2003). “Eccentric reinforced concrete beam-column joints subjected to cyclic loading.” ACI Struct. J., 100(2), 139–148.
Uzumeri, S. M. (1977). “Strength and ductility of cast-in-place beam-column joints.” Reinforced concrete structures in seismic zones, SP-53, N. Hawkins, ed., American Concrete Institute, Farmington Hills, Mich., 293–350.
Zhou, H. (2002). “Behavior of reinforced concrete eccentric and concentric beam-column joints under cyclic loading.” Ph.D. thesis, Nanyang Tech. Univ., Singapore.
Information & Authors
Information
Published In
Copyright
© 2009 ASCE.
History
Received: Oct 10, 2006
Accepted: Mar 13, 2009
Published online: Jun 15, 2009
Published in print: Jul 2009
Notes
Note. Associate Editor: Rob Y. H. Chai
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.