Vertical Earthquake Loads on Seismic Isolation Systems in Bridges
Publication: Journal of Structural Engineering
Volume 134, Issue 11
Abstract
An important consideration for the design of seismic isolation systems composed of elastomeric and lead–rubber bearings is the safety of individual bearings for maximum considered earthquake shaking. One assessment of bearing safety involves the calculation of the vertical (or axial) earthquake load on the individual seismic isolation bearings. This paper investigates the influence of vertical earthquake excitation on the response of a bridge isolated with low-damping rubber and lead–rubber bearings through earthquake simulation testing. Response data collected from the experimental program are used to determine the vertical load on the isolation system due to the vertical component of excitation. A comparison of the normalized vertical load data to the vertical base acceleration showed significant amplification of the vertical response for each simulation and configuration. Disaggregation of the axial load history showed the summation of maximum values from the vertical earthquake load and overturning moment overestimates the maximum axial load because these maximum values are unlikely to occur simultaneously. Additionally, a spectral analysis procedure using the unreduced vertical stiffness of the bearings was shown to provide a reasonable estimate of the vertical earthquake load.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers gratefully acknowledge the financial support of the Multidisciplinary Center for Earthquake Engineering Research and the Federal Highway Administration through Task D1.5 of the Federal Highway Administration Contract No. DTFH 61-98-C-0094. The writers also wish to thank Dr. Amarnath Kasalanati of DIS Inc. for providing the model bearings used in this study. The opinions expressed in this paper are those of the writers and do not reflect the opinions of the Multidisciplinary Center for Earthquake Engineering Research or the Federal Highway Administration. No guarantee regarding the results, findings, and recommendations are offered by either the Multidisciplinary Center for Earthquake Engineering Research or the Federal Highway Administration.
References
AASHTO. (1999). Guide specifications for seismic isolation design, Washington, D.C.
Buckle, I., Nagarajaiah, S., and Ferrell, K. (2002). “Stability of elastomeric isolation bearings: Experimental study.” J. Struct. Eng., 128(1), 3–11.
Buckle, I. G., and Liu, H. (1994). “Experimental determination of critical loads of elastomeric isolator at high shear strain.” NCEER Bull., 8(3), 1–5.
Button, M. R., Cronin, C., and Mayes, R. L. (2002). “Effect of vertical motions on the seismic response of highway bridges.” J. Struct. Eng., 128(12), 1551–1564.
Harris, H. G., and Sabnis, G. M. (1999). Structural modeling and experimental techniques, CRC, Boca Raton, Fla.
HITEC. (1998a). Evaluation findings for Dynamic Isolation Systems, Inc. elastomeric bearings, Civil Engineering Research Foundation, Washington, D.C.
HITEC. (1998b). Evaluation findings for Skellerup base isolation elastomeric bearings, Civil Engineering Research Foundation, Washington, D.C.
Koh, C. G., and Kelly, J. M. (1987). “Effects of axial load on elastomeric isolation bearings, Springfield, Va., Berkeley, Calif.” Earthquake Engineering Research Center, College of Engineering, Univ. of California, Berkeley, Calif.
Pacific Earthquake Engineering Research (PEER). (2005), “Strong motion database.” ⟨http://peer.berkeley.edu/⟩ (May 1, 2005).
Silva, W. J. (1997). “Characteristics of vertical ground motions for applications to engineering design.” Proc., FHWA/NCEER Workshop on the National Representation of Seismic Ground Motion for New and Existing Highway Facilities, Tech. Rep. No. NCEER-97–0010, National Center for Earthquake Engineering Research, State Univ. of New York at Buffalo, N.Y., 205–252.
Somerville, P. (2000). “Characterization of near-fault ground motions.” U.S.–Japan Workshop on the Effects of Near-Field Earthquake Shaking, Pacific Earthquake Engineering Research Center, San Francisco.
Warn, G., and Whittaker, A. S. (2006). “A study of the coupled horizontal-vertical behavior of elastomeric and lead-rubber seismic isolation bearings.” Tech. Rep. No. MCEER-06-0010, Multidisciplinary Center for Earthquake Engineering Research, State Univ. of New York at Buffalo, Buffalo, N.Y.
Warn, G. P., Whittaker, A. S., and Constantinou, M. C. (2007). “Vertical stiffness of elastomeric and lead–rubber seismic isolation bearings.” J. Struct. Eng., 133(9), 1227–1236.
Information & Authors
Information
Published In
Copyright
© 2008 ASCE.
History
Received: Dec 14, 2006
Accepted: Mar 21, 2008
Published online: Nov 1, 2008
Published in print: Nov 2008
Notes
Note. Associate Editor: Marvin W. Halling
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.