Behavior of Cold-Formed Steel Plain Angle Columns
Publication: Journal of Structural Engineering
Volume 131, Issue 3
Abstract
The main objective of this paper is to provide an efficient and accurate finite element model to understand the behavior of cold-formed steel plain angle columns. The effects of initial local and overall geometric imperfections have been taken into consideration in the analysis. The material nonlinearities of flat and corner portions of the angle sections were incorporated in the model. Failure loads and buckling modes as well as load-shortening curves of plain angle columns were investigated in this study. Furthermore, the residual stresses of a column test specimen were measured and plotted. The effect of residual stresses on the buckling behavior was studied using the finite element model. The nonlinear finite element model was verified against experimental results. The finite element analysis was performed on plain angles compressed between fixed ends over different column lengths, and column curves were obtained. An extensive parametric study was carried out using the finite element model to study the effects of cross-section geometries on the strength and behavior of angle columns. The column strengths predicted from the finite element model were compared with the design strengths calculated using the American Specification and Australian/New Zealand Standard for cold-formed steel structures. In addition, the results obtained from the finite element model were also compared with the design strengths obtained from the design rules proposed by other researchers.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers are grateful to BHP Steel Lysaght Singapore (now BlueScope Lysaght) for supplying the test specimens.
References
ABAQUS Standard User’s Manual. (2003). Hibbitt, Karlsson and Sorensen, Inc., Vols. 1, 2 and 3, Version 6.3.
American Iron and Steel Institute (AISI). (1996). Specification for the design of cold-formed steel structural members, Washington, D.C.
Australian/New Zealand Standard (AS/NZS). (1996). Cold-formed steel structures, AS/NZS 4600:1996, Standards Australia, Sydney, Australia.
Australian Standard. (1991). “Methods for tensile testing of metals.” AS 1391, Standards Association of Australia, Sydney, Australia.
Australian Standard. (1993). “Steel sheet and strip—Hot-dipped zinc-coated or aluminium/zinc-coated.” AS 1397, Standards Association of Australia, Sydney, Australia.
Bakker, M. C. M., and Pekoz, T., (2003). “The finite element method for thin-walled members-Basic principals.” Thin-Walled Struct., 41, 179–189.
Gardner, L. (2002). “A new approach to structural stainless steel design.” PhD thesis, Department of Civil and Environmental Engineering, Imperial College of Science, Technology and Medicine, London.
Hancock, G. J. (2003). “Cold-formed steel structures.”J. Constr. Steel Res., 59, 473–487.
Jiao, H., and Zhao, X. L. (2003). “Imperfections, residual stress and yield slenderness limit of very high strength (VHS) circular steel tubes.” J. Constr. Steel Res., 59, 233–249.
Madugula, M. K. S., Prabhu, T. S., and Temple, M. C. (1983). “Ultimate strength of concentrically loaded cold-formed angles.”Can. J. Civ. Eng., 10, 60–68.
Popovic, D., Hancock, G. J., and Rasmussen, K. J. R. (1999). “Axial compression tests of cold-formed angles.” J. Struct. Eng., 125(5), 515–523.
Sarawit, A. T., Kim, Y., Bakker, M. C. M., and Pekoz, T. (2003). “The finite element method for thin-walled members–Applications.” Thin-Walled Struct., 41, 191–206.
Schafer, B. W., and Pekoz, T. (1998). “Computational modeling of cold-formed steel: Characterizing geometric imperfections and residual stresses.” J. Constr. Steel Res., 47, 193–210.
Weng, C. C., and Pekoz, T. (1990). “Residual stresses in cold-formed steel members.” J. Struct. Eng., 116(6), 1611–1625.
Young, B. (2004). “Tests and design of fixed-ended cold-formed steel plain angle columns.” J. Struct. Eng., 130(12), 1931–1940.
Young, B., and Yan, J. (2002). “Finite element analysis and design of fixed-ended plain channel columns.” Finite Elem. Anal. Design, 38, 549–566.
Yu, W. W. (2000). Cold-formed steel design, 3rd Ed., Wiley, New York.
Information & Authors
Information
Published In
Copyright
© 2005 ASCE.
History
Received: Sep 23, 2003
Accepted: Jul 29, 2004
Published online: Mar 1, 2005
Published in print: Mar 2005
Notes
Note. Associate Editor: Donald W. White
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.