Seismic Resistance of Wood Shear Walls with Large OSB Panels
Publication: Journal of Structural Engineering
Volume 127, Issue 12
Abstract
Results are presented from studies on the seismic resistance of wood shear walls sheathed with large (2.4 × 2.4 m) and standard (1.2 × 2.4 m) size oriented strand board (OSB) panels. Comparisons were made among twelve 2.4 × 2.4 m walls tested under quasi-static monotonic and cyclic, as well as dynamic, loads. In push-over tests, all walls reached a drift of approximately 2.5% at maximum load. A 26% increase in shear capacity was achieved using large panels. The nails that would be at internal seams in walls with standard panels were redistributed around the exterior edges of some large panel walls. They also showed a 104% increase in shear capacity and a 30% increase in initial stiffness. These walls performed significantly better when tested dynamically, using the east-west motion recorded at Joshua Tree Station during the 1992 Landers, Calif., earthquake. Their maximum drift was reduced by approximately 25% over standard walls. Damage incurred during dynamic tests consisted mainly of nail pullout and tear out. Renailing at these locations is simple and can restore the wall to a satisfactory performance level.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Adams, N. R. ( 1987). “Plywood shear walls.” Res. Rep. 105, American Plywood Association, Tacoma, Washington.
2.
ASTM. ( 1991). “Standard method of static load test for shear resistance of framed walls for buildings.” ASTM E 564-76, Philadelphia.
3.
Atherton, G. H. ( 1982). “Ultimate strength of structural waferboard and particleboard diaphragms.” Forest Res. Lab., Oregon State University, Corvallis, Oreg.
4.
Atherton, G. H. ( 1983). “Ultimate strength of particleboard diaphragms.” Forest Products J., 33(5), 22–26.
5.
Canadian Standards Association (CSA). ( 1992). “Test method for construction sheathing.” CAN/CSA-O325.0-92, Ottawa.
6.
Comité Europeen de Normalisation (CEN). ( 1995). “Timber structures—test methods—cyclic testing of joints made with mechanical fasteners.” Draft EN TC 124.117, Brussels.
7.
Council of Forest Industries of British Columbia (COFI). ( 1979). Douglas-fir plywood diaphragms, Vancouver.
8.
Dolan, J. D. ( 1989). “The dynamic response of timber shear walls.” PhD thesis, Dept. of Civ. Engrg., University of British Columbia, Vancouver.
9.
Dolan, J. D. ( 1994). “Proposed test method for dynamic properties of connections assembled with mechanical fasteners.” J. Testing and Evaluation, 22(6), 542–547.
10.
Durham, J., He, M., Lam, F. and Prion, H. G. L. ( 1998). “Seismic resistance of wood shear walls with oversize sheathing panels.” Proc., World Conf. on Timber Engrg., Vol. 1, Presses Polytechniques et Universitaires Romandes, Montreux-Lausanne, Switzerland, 396–403.
11.
Easley, J. T., Foomani, M., and Dodds, R. H. (1982). “Formulas for wood shear walls.”J. Struct. Div., ASCE, 108(11), 2460–2478.
12.
Ehlbeck, J. ( 1979). “Nailed joints in wood structures.” Res. Rep. No. 166, Virginia Polytechnic Institute and State University, Blacksburg, Va.
13.
Falk, R. H., and Itani, R. Y. (1989). “Finite element modeling of wood diaphragms.”J. Struct. Engrg., ASCE, 115(3), 543–559.
14.
Filiatrault, A. ( 1990). “Static and dynamic analysis of timber shear walls.” Can. J. Civ. Engrg., 17(4), 643–651.
15.
Filiatrault, A., Uang, C.-M., and Seible, F. ( 2000). “Ongoing seismic testing and analysis program in the CUREe-Caltech woodframe project in California.” Proc., World Conf. on Timber Engrg. 2000. Paper No. 7.1.4, University of British Columbia, Vancouver.
16.
Foliente, G. C., and Zacher, E. G. ( 1994). “Performance tests of timber structural systems under seismic loads.” Proc., Res. Needs Workshop, University of California, Richmond, Calif., 21–86.
17.
Foschi, R. O. ( 1974). “Load-slip characteristics of nails.” Wood Sci., 7(1), 69–76.
18.
Foschi, R. O. ( 1977). “Analysis of wood diaphragms and trusses, Part one: Diaphragms.” Can. J. Civ. Engrg., 4(3), 345–352.
19.
Foschi, R. O. ( 1990). Diaphragm analysis program–User's manual (Version 1.1), University of British Columbia, Vancouver.
20.
Gupta, A. K., and Kuo, G. P. (1985). “Behavior of wood framed shear walls.”J. Struct. Engrg., ASCE, 111(8), 1722–1733.
21.
Hall, J. F. ( 2000). “The CUREe-Caltech woodframe project.” Proc., World Conf. on Timber Engrg. 2000, Paper No. 7.1.1, University of British Columbia, Vancouver.
22.
He, M., Lam, F., and Prion, H. G. L. ( 1998). “Influence of cyclic test protocols on performance of wood based shear walls.” Can. J. Civ. Engrg., 25, 539–550.
23.
Hunt, R. D., and Bryant, A. H. (1990). “Laterally loaded nail joints in wood.”J. Struct. Engrg., ASCE, 116(1), 111–124.
24.
Itani, R. Y., and Cheung, C. K. (1984). “Nonlinear analysis of sheathed wood diaphragms.”J. Struct. Engrg., ASCE, 110(9), 2137–2147.
25.
Kamiya, F. ( 1988). “Nonlinear earthquake response analysis of sheathed wood walls by a computer actuator on-line system.” Proc., 1988 Int. Timber Engrg. Conf., Vol. 1, Forest Products Society, Madison, Wis., 838–847.
26.
Karacabeyli, E. ( 1995). “Lateral resistance of nailed shear walls subjected to static and cyclic displacements.” Res. Rep. Presented at FPS 49th Annu. Meeting, Forest Products Society, Madison, Wis.
27.
Karacabeyli, E. ( 1996a). “Joints made with mechanical fasteners.” Meeting Notes of ISO TC 165 Timber Struct. Working Group 7 Meeting, Canadian Plywood Association, North Vancouver, Canada.
28.
Karacabeyli, E. ( 1996b). “Quasi-static reversed-cyclic testing of nailed joints.” Proc., Int. Council for Build. Res. Studies and Documentation, Working Commission W18—Timber Struct., Meeting 29, Universität Karlsruhe, Karlsruhe, Germany, 29–77.
29.
Krawinkler, H., Parisi, F., Ibarra, L., Ayoub, A., and Medina, R. ( 2000). “Development of a testing protocol for wood frame structures.” Proc., Curee-Caltech Woodframe Project, Element 1—Res. Meeting, University of California, San Diego.
30.
Lam, F., Prion, H. G. L., and He, M. (1997). “Lateral resistance of wood shear walls with large sheathing panels.”J. Struct. Engrg., ASCE, 123(12), 1666–1673.
31.
Latendresse, V., and Ventura, C. E. ( 1995). “Shake table testing of `ANTI-RAKKER' device for plywood shear walls.” Res. Rep., Dept. of Civ. Engrg., University of British Columbia, Vancouver.
32.
Rainer, J. H., and Karacabeyli, E. ( 1999). “Performance of wood-frame building construction in earthquakes.” Forintek Spec. Publ. Rep. No. SP-40, Forintek Canada Corp. Vancouver.
33.
Rose, J. D. ( 1995). “Performance of wood structural panel shear walls under cyclic (reversed) loading.” Res. Rep. Presented at FPS 49th Annu. Meeting, Forest Products Society, Madison, Wis.
34.
Stewart, W. G. ( 1987). “The seismic design of plywood sheathed shearwalls.” PhD dissertation, Dept. of Civ. Engrg., University of Canterbury, Christchurch, New Zealand.
35.
TECO. ( 1980). “Summary of racking tests conducted on waferboard sheathing.” Rep. Prepared for Canadian Waferboard Assoc., TECO, Eugene, Oreg.
36.
TECO. ( 1981). “Racking load test report on 3 application procedures of 7/16 inch waferboard.” Rep. Prepared for Canadian Waferboard Assoc., TECO, Eugene, Oreg.
37.
Tissel, J. R., and Elliott, J. R. ( 1977). “Plywood diaphragms.” Res. Rep. 138, American Plywood Association, Tacoma, Wash.
38.
Tuomi, R. L., and McCutcheon, W. J. (1978). “Racking strength of light-frame nailed walls.”J. Struct. Div., ASCE, 104(7), 1131–1140.
39.
Wilkinson, T. L. (1972). “Analysis of nailed joints with dissimilar members.”J. Struct. Div., ASCE, 98(9), 2005–2013.
Information & Authors
Information
Published In
History
Received: Mar 24, 2000
Published online: Dec 1, 2001
Published in print: Dec 2001
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.