Biaxial Interaction Diagrams for Short RC Columns of Any Cross Section
Publication: Journal of Structural Engineering
Volume 125, Issue 6
Abstract
A general method that determines the biaxial interaction diagrams for any orientation of the neutral axis of a reinforced concrete (RC) short column of any cross section under axial load and bending about two axes is presented. Closed form expressions for MnX, MnY, and Pn are derived that evaluate the theoretical ultimate strength of RC short columns using (1) Gauss' integral method for equilibrium; (2) a nonlinear stress-strain relationship for the concrete; and (3) a multilinear elastoplastic relationship for the reinforcement. These equations and the proposed method can be reproduced by another user with minimal calculations (as opposed to other methods), allowing the designer to investigate the biaxial bending behavior and failure mode of short RC columns under compression or tension. The proposed method can also be utilized in the study of the effects of creep and confinement of the concrete on the strength and failure mode of RC short columns of any cross section under biaxial bending and axial load. It was found that the effects of creep and confinement in the concrete are significant on the interaction curves, particularly at high compressive loads, whereas strain hardening of the reinforcement affects the response at high tensile loads. Five numerical examples are presented in detail to verify and show the effectiveness of the proposed method.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Aas-Jacobsen, A. ( 1964). “Biaxial eccentricities in ultimate load design.” ACI J., 61(3), 293–315.
2.
Al-Noury, S., and Chen, W. F. ( 1982). “Behavior and design of reinforced and composite concrete sections.” Proc., ASCE, Reston, Va., 108(6), 1266–1284.
3.
Anderson, P., and Lee, H. N. ( 1951). “A modified plastic theory of reinforced concrete.” Bull. 33, University of Minnesota, Minneapolis, 54(19).
4.
Ansari, F. ( 1978). “Design of reinforced concrete members for combined bending and tension,” MS thesis, University of Colorado, Boulder, Colo.
5.
Barzegar, F., and Erasito, T. ( 1995). “Concrete sections under biaxial bending: Interactive analysis with spreadsheets.” ACI Concrete Int., 17(12), 28–33.
6.
Bresler, B. ( 1960). “Design criteria for reinforced columns under axial load and biaxial bending.” ACI J., 57(5), 481–490.
7.
Brondum-Nielsen, T. ( 1982). “Ultimate limit states of cracked arbitrary concrete sections under axial load and biaxial bending.” ACI Concrete Int., 4(11), 51–55.
8.
Brondum-Nielsen, T. ( 1983). “Ultimate flexural capacity of partially or fully prestressed cracked arbitrary concrete sections under axial load combined with biaxial bending.” ACI Concrete Int., 5(1), 75–78.
9.
Brondum-Nielsen, T. ( 1987a). “Serviceability limit state analysis of concrete sections with circular holes under axial bending.” ACI Struct. J., 84(5), 293–295.
10.
Brondum-Nielsen, T. ( 1987b). “Ultimate flexural capacity of cracked polygonal concrete sections with circular holes under biaxial bending.” ACI Struct. J., 84(3), 212–215.
11.
“Building code requirements for reinforced concrete (ACI 318-95) and commentary (ACI 318R-95).” (1995). American Concrete Institute, Detroit.
12.
Chu, K.-H., and Pabarcius, A. ( 1958). “Biaxially loaded reinforced concrete columns.” Proc., ASCE, Reston, Va., 84(8), 1–27.
13.
Dinsmore, C. I. ( 1982). “Column analysis with a programmable calculator.” ACI Concrete Int., 4(11), 32–36.
14.
Dundar, C. (1990). “Concrete box sections under biaxial bending and axial load.”J. Struct. Engrg., ASCE, 116(3), 860–865.
15.
Fleming, J. F., and Werner, S. D. ( 1965). “Design of columns subjected to biaxial bending.” ACI J., 62(3), 327–342.
16.
Furlong, R. W. ( 1961). “Ultimate strength of square columns under biaxially eccentric load.” ACI J., 57(9), 1129–1140.
17.
Gouwens, A. J. ( 1975). “Biaxial bending simplified.” Reinforced concrete columns, ACI SP-50. American Concrete Institute, Detroit, 233–261.
18.
Gurfinkel, G. (1970). “Analysis of footings subjected to biaxial bending.”J. Struct. Div., ASCE, 93(6), 1049–1059.
19.
Heindahm, P. O., and Bianchini, A. C. ( 1975). “Ultimate strength of biaxially eccentrically loaded concrete columns reinforced with high strength steel.” Reinforced concrete columns, ACI SP-50. American Concrete Institute, Detroit, 93–117.
20.
Hsu, C.-T. T. (1985). “Biaxially loaded L-shaped reinforced concrete columns.”J. Struct. Engrg., ASCE, 111(12), 2576–2595 [Errata, 1988, 114(11), 2629].
21.
Hsu, C.-T. T. ( 1986). “Reinforced concrete members subject to combined biaxial bending and tension.” ACI J., 83(1), 137–144.
22.
Hsu, C.-T. T. ( 1987). “Channel-shaped reinforced concrete compression members under biaxial bending.” ACI Struct. J., 84(3), 201–211 [Errata, 1988, 85(3), 240].
23.
Hsu, C.-T. T. ( 1988). “Analysis and design of square and rectangular columns by equation of failure surface.” ACI Struct. J., 85(2), 167–179.
24.
Hsu, C.-T. T. ( 1989). “T-shaped reinforced concrete members under biaxial bending and axial compression.” ACI Struct. J., 86(4), 460–468.
25.
Hsu, C.-T. T., and Mirza, M. S. (1973). “Structural concrete-biaxial bending and compression.”J. Struct. Engrg., ASCE, 99(2), 285–290.
26.
Kawakami, M. T., Kagaya, M., and Hirata, M. ( 1985). “Limit states of cracking and ultimate strength of arbitrary concrete sections under biaxial loading.” ACI J., 82(1), 203–212.
27.
Lachance, L. ( 1980). “Stress distribution in reinforced concrete sections subjected to biaxial loading.” ACI J., 77(2), 116–123.
28.
Marin, J. ( 1979). “Design aids for L-shaped reinforced concrete columns.” ACI J., 76(11), 1197–1216.
29.
Marin, J. (1980). “Computing unidimensional normal stress resultants.”J. Struct. Engrg., ASCE, 106(1), 233–245.
30.
Parme, A. L., Nieves, J. M., and Gouwens, A. J. ( 1966). “Capacity of reinforced rectangular columns subjected to biaxial bending.” ACI J., 63(9), 911–923.
31.
Ramamurthy, L. N. ( 1966). “Investigation of the ultimate strength of square and rectangular columns under biaxially eccentric loads.” Symp. on Reinforced Concrete Columns, ACI SP-13, American Concrete Institute, Detroit, 263–298.
32.
Ramamurthy, L. N., and Khan, A. H. (1983). “L-shaped column design for biaxial eccentricity.”J. Struct. Engrg., ASCE, 109(8), 1903–1917.
33.
Ross, D. A., and Yen, J. R. ( 1986). “Interactive design of reinforced concrete columns with biaxial bending.” ACI J., 83(6), 988–993.
34.
Smith, J. C. ( 1973). “Biaxially loaded concrete interaction curve.” Comp. and Struct., 3, 1461–1464.
35.
Wang, C. ( 1988). “Solving the biaxial bending problem in reinforced concrete by a three-level iteration procedure.” Microcomp. in Civ. Engrg., 3, 311.
36.
Wang, C., and Salmon, C. G. ( 1992). Reinforced concrete design, 5th Ed., Harper & Row, New York.
37.
Warner, R. F. ( 1969). “Biaxial moment thrust curvature relations.” Proc., ASCE, Reston, Va., 95(5), 923–940.
38.
Winter, G., and Nilson, A. H. ( 1991). Design of concrete structures, 11th Ed., McGraw-Hill, New York.
39.
Yen, J. R. (1991). “Quasi-Newton method for reinforced concrete column analysis and design.”J. Struct. Engrg., ASCE, 117(3), 657–666.
Information & Authors
Information
Published In
History
Received: Nov 19, 1997
Published online: Jun 1, 1999
Published in print: Jun 1999
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.