UBC Seismic Serviceability Regulations: Critical Review
Publication: Journal of Structural Engineering
Volume 117, Issue 7
Abstract
This paper discusses the widely accepted seismic design limit state philosophy and the serviceability limit state requirements for stress and drift controls in the 1988 UBC. The limit state philosophy implemented in the UBC is compared with that in the Japanese code. Although the service (or moderate) design earthquake is explicitly specified in the Japanese code, this design earthquake is indirectly assumed in the UBC by specifying a drift limit that is inversely proportional to the factor. The study shows that UBC cannot control the level of stress in steel building structures for service design earthquakes; the allowable seismic stress implied by UBC was found to be too high for ductile structures and too low for structures of limited ductility. The UBC story drift limit of (or may be too high, and the drift limit of 0.005 (or 0.004) is too conservative for buildings with low values.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Allowable stress design (ASD) manual of steel construction. (1989). Amer. Inst. Of Steel Constr. (AISC), Chicago, Ill.
2.
Bertero, V. V. (1986). “Evaluation of response reduction factors recommended by ATC and SEAOC.” Proc., 3rd U.S. Nat. Conf. Earthquake Engrg., Earthquake Engrg. Res. Inst., Charleston, S.C., 1663–1673.
3.
Bertero, V. V., and Bresler, B. (1977). “Failure criteria (limit states).” Proc., 6th World Conf. Earthquake Engrg., Int. Assoc. for Earthquake Engrg., New Delhi, India, 77–87.
4.
Blume, J. A. (1977). “Allowable stresses and earthquake performance.” Proc., 6th World Conf. Earthquake Engrg., Int. Assoc. for Earthquake Engrg., New Delhi, India, 165–174.
5.
“Building code requirements for reinforced concrete.” (1989). ACI 318‐89, Amer. Concrete Inst., Detroit, Mich.
6.
Degenkolb, H. J. (1972). “Basic design criteria of the recommended lateral force requirements and commentary.” J. Struct. Div., ASCE, 98(9), 1913–1922.
7.
Design standard for steel structures. (1970). Arch. Inst. of Japan, Tokyo, Japan.
8.
Earthquake resistant regulations—a world list. (1988). Int. Assoc. for Earthquake Engrg., Tsukuba, Japan.
9.
Freeman, S. A. (1982). “An alternate seismic design approach.” ATC 10‐1, Applied Technology Council, 203–212.
10.
Freeman, S. A. (1985). “Drift limits: Are they realistic.” Earthquake Spectra, 1(2), 355–362.
11.
“An investigation of the correlation between earthquake ground motion and building performance.” (1982). ATC 3‐10, Applied Technology Council, Palo Alto.
12.
Kato, B. (1986). “Seismic design criteria for steel buildings.” Proc., Pacific Struct. Steel Conf., Auckland, New Zealand, vol. 1, 133–147.
13.
Kato, B., and Akiyama, H. (1982). “Seismic design of steel buildings.” J. Struct. Div., ASCE, 108(8), 1709–1721.
14.
Load and resistance factor design (LRFD) manual of steel construction. (1986). Amer. Inst. of Steel Constr., Chicago, Ill.
15.
NEHRP recommended provisions for the development of seismic regulations for new buildings. (1988). Bldg. Seismic Safety Council, Washington, D.C.
16.
Recommended lateral force requirements and commentary. (1988). Struct. Engrs. Assoc. of California, San Francisco, Calif.
17.
Rojahn, C. (1988). “An investigation of structural response modification factors,” Proc., 9th World Conf. Earthquake Engrg., Int. Assoc. for Earthquake Engrg., Tokyo, Japan, vol. V, 1087–1092.
18.
“Tentative provisions for the development of seismic regulations for buildings.” (1978). ATC 3‐06, Applied Technology Council, Palo Alto.
19.
Uang, C.‐M. (1991a). “Comparison of seismic force reduction factors used in USA and Japan.” Earthquake Engrg. Struct. Dynamics, 20(3).
20.
Uang, C.‐M. (1991b). “Establishing R (or ) and factors for building seismic provisions.” J. Struct. Engrg., ASCE, 117(1), 19–28.
21.
Uniform building code (UBC). (1985). Int. Conf. of Bldg. Officials, Whittier, Calif.
22.
Uniform building code (UBC). (1988). Int. Conf. of Bldg. Officials, Whittier, Calif.
Information & Authors
Information
Published In
Copyright
Copyright © 1991 ASCE.
History
Published online: Jul 1, 1991
Published in print: Jul 1991
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.