Truck‐Tire Steel Grid Deck Contact Pressure Distributions
Publication: Journal of Structural Engineering
Volume 116, Issue 3
Abstract
This study deals with the mathematical and experimental determination of contact pressure distribution between bridge decks and truck tires. The variables associated with this study are tire inflation pressure, axle loads, treaded or bald tire, and main bar spacing and its orientation with traffic flow. A classical structural mechanics approach for contact pressure distribution has been developed by idealizing the open steel grid deck and the tire as two different springs in series. In addition, an approximate, but simplified, distribution procedure has been developed. Synthesis of our test data reveals the following trends: (1) Increase in inflation pressure increases the peak values of the contact pressure distribution profile; (2) maximum contact pressure is found to be about 2.5 times the average pressure computed from the current AASHTO specifications for highway bridges; (3)rate of increase in contact pressure is not as rapid as the increase in axle loads; (4)fully treaded tires are found to result in higher contact pressures than the bald tires; and (5) load carried by main bars is higher when they are placed perpendicular to, rather than parallel to the traffic flow.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Ballinger, C. A., and Gade, R. H. (1973). “Evaluation of the structural behavior of typical highway inlet grates with recommended structural design criteria.” Final Report, Federal Highway Admin., Washington, D.C., Dec.
2.
Berger, M. (1959). “Kinematics of a rolling tire and its application to tire performance.” J. Appl. Polymer Sci., II(5), 174–180.
3.
Berger, R. H. (1977). “Extending the service life of existing bridges by increasing their loading carrying capacity.” Presented at FCP Conf., Atlanta, Ga., Oct.
4.
Bonse, R. P. H., and Kuhn, S. H. (1959). “Dynamic forces exerted by moving vehicles on a road surface.” Highway Res. Board Bulletin, 233, 9–32.
5.
Frank, F., and Hofferberth, W. (1967). “Mechanics of the pneumatic tire.” Rubber Chem. and Tech., 40(1), 271–322.
6.
GangaRao, H. V. S. (1980). “Feasibility of steel grid decks for bridge floors.” Final Report, prepared for West Virginia Dept. of Highways/Fed. Highway Admin., Charleston, W.V., Jul.
7.
GangaRao, H. V. S., and Vali, A. (1988). “Determination of truck tire‐open steel grid deck contact pressure distribution.” Final Report, prepared for West Virginia Dept. of Highways, Fed. Highway Admin., Charleston, W.V., Jun.
8.
GangaRao, H. V. S., et al. (1987). “Behavior and design of open steel grid decks for highway bridges.” Report No. FHWA‐WV‐80, Morgantown, W.V., Aug.
9.
Lippmann, S. A., and Oblizajek, K. L. (1974). “The distributions of stress between the tread and the road for freely rolling tires.” SAE Paper 740072, Vol. 83, Automatic Engrg. Congress, Detroit, Mich.
10.
Marshek, M. K., et al. (1986). “Experimental determination of truck tire‐pavement contact pressure distribution.” 65th Annual Meeting of Transp. Res. Board, Washington, D.C., Jan.
11.
Moore, D. F. (1975). The friction of pneumatic types. Elsevier, New York, N.Y.
12.
Ridha, R. A., et al. (1983). “Finite element modeling of a homogeneous pneumatic tire subjected to footprint loadings.” Tire Sci. and Tech., II(1–4), 50–63.
13.
Ridha, R. A., et al. (1985). “Contact loading of a rubber disk.” Tire Sci. and Tech., 13(1), 3–15.
14.
Roberts, F. L., and Rosson, B. T. (1985). “Effects of higher tire pressures on strain in thin ACP.” Final Report, Texas Transp. Inst., Jan.
15.
Roberts, F. L., et al. (1985). “The effects of tire pressures on pavement.” Final Report, Texas Transp. Inst., Dec.
16.
Seitz, N., and Hunmann, A. W. (1971). “Forces and displacement in contact area of free rolling tires.” SAE Trans., 80, Jun.
17.
Standard specifications for highway bridges. (1983). AASHTO, Washington, D.C.
18.
Worrell, D. T., and Haynes, R. R. (1968). “Search for a strength and toughness test for crushed stones.” Final Report, West Virginia Univ., submitted to State Bond Commission of West Virginia, Charleston, W.V., Dec.
19.
Woods, K. B., ed. (1960). Highway engineering handbook. McGraw‐Hill, New York, N.Y.
Information & Authors
Information
Published In
Copyright
Copyright © 1990 ASCE.
History
Published online: Mar 1, 1990
Published in print: Mar 1990
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.