Tests of Full‐Size Gusset Plate Connections
Publication: Journal of Structural Engineering
Volume 111, Issue 3
Abstract
The paper presents an evaluation of the behavior and strength of gusset plates on the basis of an experimental investigation of full‐scale diagonal bracing connections. Sugh connections commonly occur in heavy industrial structures, for example. The evaluations are based on analyses of load and deformation data that were generated during the tests, including the failure patterns for the plates. A total of six tests were run, using three bracing member orientation angles. The results are correlated with analytical studies, with special emphasis on recent finite element work. The results are found to be in reasonable agreement Current design practices are discussed briefly; some of the methods are shown to be in acceptable agreement with the tests. It is shown that plate boundaries, plate buckling, and related out‐of‐plane bending phenomena have significant effects on the plate behavior. Recommendations for additional work are also made.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Butler, L. J., and Kulak, G. L., “Strength of Fillet Welds as a Function of Load,” Welding Journal, AWS, Research Supplement, Vol. 50, No. 5, May, 1971.
2.
Canadian Standards Association (CSA), “Steel Structures for Buildings—Limit States Design,” CSA Standard No. S16.1‐74, CSA, Rexdale, Ontario, 1974.
3.
Canadian Standards Association (CSA), “General Requirements for Rolled and Welded Structural Quality Steel,” CSA Standard No. G40.20—M78, CSA, Rexdale, Ontario, May, 1978.
4.
Chakrabarti, S. K., and Bjorhovde, R., “Tests of Gusset Plate Connections,” Structural Engineering Report, Department of Civil Engineering, University of Arizona, Tucson, Ariz., Apr., 1983.
5.
Davis, C. S., “Computer Analysis of the Stresses in a Gusset Plate,” thesis presented to the University of Washington, at Seattle, Wash., in 1967, in partial fulfillment of the requirements for the degree of Master of Science.
6.
Fisher, J. W., “Behavior of Fasteners and Plates with Holes,” Journal of the Structural Division, ASCE, Vol. 91, No. ST6, Dec., 1965.
7.
Fisher, J. W., and Struik, J. H. A., Guide to Design Criteria for Bolted and Riveted Joints, Wiley‐Interscience, New York, N.Y., 1974.
8.
Hardash, S. G., and Bjorhovde, R., “Gusset Plate Design Utilizing Block‐Shear Concepts,” Structural Engineering Report, Department of Civil Engineering, University of Arizona, Tucson, Ariz., Aug., 1984.
9.
Hardin, B. O., “Experimental Investigation of the Primary Stress Distribution in the Gusset Plates of a Double Plane Pratt Truss Joint with Chord Splice at the Joint,” Bulletin No. 49, Engineering Experiment Station, University of Kentucky, Sept., 1958.
10.
Irish, D. J., and Bjorhovde, R., “Strength and Behavior of Connection Components,” Structural Engineering Report, Department of Civil Engineering, University of Arizona, Tucson, Ariz., June, 1983.
11.
Irvan, W. G., “Experimental Study of Primary Stresses in Gusset Plates of a Double Plane Pratt Truss,” Bulletin No. 46, Engineering Experiment Station, University of Kentucky, Dec., 1957.
12.
Rabern, D. A., “Stress, Strain and Force Distribution in Gusset Plate Connections,” thesis presented to the University of Arizona, in Tucson, Ariz., in 1983, in partial fulfillment of the requirements for the degree of Master of Science.
13.
Struik, J. H. A., “Applications of Finite Element Analysis to Non‐Linear Plane Stress Problems,” thesis presented to Lehigh University, at Bethlehem, Pa., in 1972, in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
14.
Vasarhelyi, D. D., “Tests of Gusset Plate Models,” Journal of the Structural Division, ASCE, Vol. 97, No. ST2, Feb., 1971.
15.
Whitmore, R. E., “Experimental Investigation of Stresses in Gusset Plates,” Bulletin No. 16, Engineering Experiment Station, University of Tennessee, May, 1952.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 111 • Issue 3 • March 1985
Pages: 667 - 684
Copyright
Copyright © 1985 ASCE.
History
Published online: Mar 1, 1985
Published in print: Mar 1985
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.