Approximate Linear Analysis of Concrete Fracture by R‐Curves
Publication: Journal of Structural Engineering
Volume 110, Issue 6
Abstract
Using linear elastic fracture analysis, the energy consumed per unit length of fracture (fracture energy) varies with the crack length, as described by the resistance curve (R‐curve). This concept, originally proposed for metals, is developed here into a practical, applicable form for concrete. The energy release rate is determined by an approximate linear elastic fracture analysis based on a certain equivalent crack length, which differs from the actual crack length, and is solved as part of structural analysis. It is shown that such an analysis, coupled with the R‐curve concept, allows achieving satisfactory fits of the presently existing fracture data obtained with three‐point and four‐point bent specimens. Without the R‐curve, the use of an equivalent crack length in linear analysis is not sufficient to achieve a satisfactory agreement with these data. The existing data can be described equally well with various formulas for the R‐curve, and the material parameters in the formula can vary over a relatively broad range without impairing the representation of test data. Only the overall slope of the R‐curve, the initial value, and the final value are important. A parabola seems to be the most convenient shape of R‐curve because the failure load may then be solved from a quadratic equation. For the general case, a simple algorithm to calculate the failure load is given. Deviations from test data are analyzed statistically, and an approximate relationship of the length parameter of the R‐curve to the maximum aggregate size is found.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Baant, Z. P., “Crack Band Model for Fracture of Geomaterials,” Proceedings, 4th International Conference on Numerical Methods in Geomechanics, Edmonton, Alberta, Canada, Vol. 3, Z. Eisenstein, ed., June, 1982, pp. 1137–1152.
2.
Baant, Z. P., “Mechanics of Fracture and Progressive Cracking in Concrete Structures,” Report 83‐2/428m, Center for Concrete and Geomaterials, Northwestern University, Evanston, Ill., Feb., 1983; to appear as Chapter 1 in Fracture Mechanics Applied to Concrete Structures, G. C. Sih, ed., Martinus Nijhoff Publ., The Hague.
3.
Baant, Z. P., and Oh, B. H., “Crack Band Theory for Fracture of Concrete,” Materials and Structures (RILEM, Paris), Vol. 16, 1983, pp. 155–177.
4.
Baant, Z. P., and Cedolin, L., “Blunt Crack Band Propagation in Finite Element Analysis,” Journal of the Engineering Mechanics Division, ASCE, Vol. 105, No. EM2, Apr., 1979, pp. 297–313.
5.
Baant, Z. P., and Cedolin, L., “Fracture Mechanics of Reinforced Concrete,” Journal of the Engineering Mechanics Division, ASCE, Vol. 106, No. EM6, Dec., 1980
(discussion and closure Vol. 108, pp. 464–471).
6.
Broek, D., Elementary Engineering Fracture Mechanics, Noordhoff International Publishing, Leyden, Netherlands, 1974.
7.
Brown, J. H., “Measuring the Fracture Toughness of Cement Paste and Mortar,” Magazine of Concrete Research, Vol. 24, No. 81, Dec., 1972.
8.
Carpinteri, A., “Experimental Determination of Fracture Toughness Parameters and for Aggregative Materials,” presented at the Mar. 23–Apr. 3, 1981, 5th International Conference on Fracture, Cannes, France, “Advances in Fracture Research,” D. Frangois, ed., Vol. 4, pp. 1491–1498.
9.
Entov, V. M., and Yagust, V. I., “Experimental Investigation of Laws Governing Quasi‐Static Development of Macrocracks in Concrete,” Mechanics of Solids (translation from Russian), Vol. 10, No. 4, 1975, pp. 87–95.
10.
Gjørv, O. E., Sorenson, S. I., and Arnesen, A., “Notch Sensitivity and Fracture Toughness of Concrete,” Cement and Concrete Research, Vol. 7, 1977, pp. 333–344.
11.
Huang, C. M. J., “Finite Element and Experimental Studies of Stress Intensity Factors for Concrete Beams,” thesis presented to the Kansas State University, at Kansas, in 1981, in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
12.
Hutchinson, J. W., and Paris, P. C., “Stability Analysis of J‐Controlled Crack Growth; Elastic‐Plastic Fracture,” ASTM‐STP668, American Society for Testing and Materials, 1979, pp. 37–64.
13.
Irwin, G. R., Applied Mathematics Research, Vol. 3, No. 65, 1964.
14.
Kaplan, M. F., “Crack Propagation and the Fracture of Concrete,” American Concrete Institute Journal, Vol. 58, No. 11, Nov., 1961.
15.
Knott, J. F., “Fundamentals of Fracture Mechanics,” Butterworth, London, England, 1973.
16.
Krafft, J. M., Sullivan, A. M., Boyle, R. W., “Effect of Dimensions on Fast Fracture Instability of Notched Sheets,” Cranfield Symposium, 1961, Vol. 1, pp. 8–28.
17.
Mindess, S., Lawrence, F. V., and Kesler, C. E., “The J‐Integral as a Fracture Criterion for Fiber Reinforced Concrete,” Cement and Concrete Research, Vol. 7, 1977, pp., 731–742.
18.
Paris, P. C., et al., “The Theory of Tearing Instability of the Tearing Mode of Elastic‐Plastic Crack Growth,” ASTM Special Technical Publication, No. 668 and 677, 1979, pp. 5–36.
19.
Parker, A. P., “The Mechanics of Fracture and Fatigue,” E. & F.N. Spon, Ltd., London, 1981.
20.
Petersson, P. E., “Fracture Energy of Concrete: Method of Determination,” Cement and Concrete Research, Vol. 10, 1980, pp. 78–89.
21.
Petersson, P. E., “Fracture Energy of Concrete: Practical Performance and Experimental Results,” Cement and Concrete Research, Vol. 10, 1980, pp. 91–101.
22.
Shah, S. P., and McGarry, F. J., “Griffith Fracture Criterion and Concrete,” Journal of the Engineering Mechanics Division, ASCE, Vol. 97, No. EM6, Proc. Paper 8597, Dec., 1971, pp. 1663–1676.
23.
Sok, C., and Baron, J., “Mécanique de la Rupture Appliquée au Béton Hydraulique,” Cement and Concrete Research, Vol. 9, 1979, pp. 641–648.
24.
Tada, H., Paris, P. C., and Irwin, G. R., The Stress Analysis of Cracks Handbook, Del Research Corp., Hellertown, Pa., 1973.
25.
Visalvanich, K., and Naaman, A. E., “Fracture Model for Fiber Reinforced Concrete,” Journal of American Concrete Institute, Vol. 80, Mar.–Apr., 1983, pp. 128–138.
26.
Walsh, P. F., “Fracture of Plain Concrete,” The Indian Concrete Journal, Vol. 46, No. 11, Nov., 1979, pp. 469, 470, and 476.
27.
Wecharatana, M., and Shah, S. P., “Slow Crack Growth in Cement Composites,” Journal of Structural Engineering Division, ASCE, Vol. 108, No. ST6, June, 1982, pp. 1400–1413.
28.
Wnuk, M. P., Bažant, Z. P., and Law, E., “Stable Growth of Fracture in Brittle Aggregate Materials,” Report, Center for Concrete and Geomaterials, Northwestern University, Evanston, Ill., Oct., 1983; also to appear in Theoretical and Applied Fracture Mechanics, G. Sih, ed., Elsevier‐North Holland.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 110 • Issue 6 • June 1984
Pages: 1336 - 1355
Copyright
Copyright © 1984 ASCE.
History
Published online: Jun 1, 1984
Published in print: Jun 1984
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.