Centrifugal Modeling of Bearing Capacity of Shallow Foundations on Sands
Publication: Journal of Geotechnical Engineering
Volume 121, Issue 10
Abstract
The study of shallow footings under plane-strain conditions became important when many researchers reported the lack of agreement between theoretical and experimental findings. A better understanding of the behavior of granular material under different stress levels and strain conditions encouraged further research in this field. In order to understand the behavior of footings and study the differences between theoretical and experimental observations, an experimental program was devised taking into account some factors that affect the theoretical assumptions. In this paper, the centrifuge has been utilized to study the effects of load eccentricity, load inclination, and initial burial on the bearing capacity of shallow strip footings on a dense sand. Fine silica sand, F-75 in a dense state with a relative density of 88%, was used. A plane-strain condition was obtained by testing three adjacent footings of the same width along one line. Footings were loaded with a stiff mechanism to give uniform displacement and, therefore, the one in the middle was under a plane strain condition. Test results indicate that plane strain conditions were modeled using this design. Experimental values of the bearing capacity factors N q and N γ are presented and compared to theoretical values given by different researchers. Results show that the linear pressure distribution at the base of the footing is a good approximation of observed behavior. It was noticed that single-sided failure always occurs regardless of load eccentricity and inclination. In addition, results show that failure occurs in a progressive manner.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Aiban, S., and Znidarić, D. (1991). “Shallow footings on sands under vertical central, eccentric and inclined loads.”Proc., Centrifuge `91 Conf., Balkema, Rotterdam, The Netherlands.
2.
Bishop, A. W. (1961). “Discussion on soil properties and their measurement.”Proc., 5th Int. Conf. on Soil Mech. and Found. Engrg., Dunod, Paris, France, Vol. III, 92–100.
3.
Bishop, A. W.(1966). “The strength of soils as engineering materials.”Géotechnique, London, England, 16(2), 91–130.
4.
Cornforth, D. H.(1964). “Some experiments on the influence of strain conditions on the strength of sand.”Géotechnique, London, England, 14(2), 143–167.
5.
Das, B. (1987). Theoretical foundation engineering. Elsevier Science Publishers B. V., Amsterdam, The Netherlands.
6.
Davis, H. E., and Woodward, R. J. (1949). “Some laboratory studies of factors pertaining to the bearing capacity of soils.”Proc., Hwy. Res. Board, Washington, D.C., Vol. 29, 467–476.
7.
De Beer, E. E. (1965a). “Bearing capacity and settlement of shallow foundations on sand.”Proc., Symp., Duke Univ., Durham, N.C., 15–34.
8.
De Beer, E. E. (1965b). “The scale effect on the phenomenon of progressive rupture in cohesionless soils.”Proc., 6th Int. Conf. on Soil Mech. and Found. Engrg., Univ. of Toronto, Canada, Vol. II, 13–17.
9.
De Beer, E. E.(1970). “Experimental determination of the shape factors and the bearing capacity factors of sand.”Géotechnique, London, England, 20(4), 387–411.
10.
Dhillon, G. S. (1961). “The settlement, tilt and bearing capacity of footing under central and eccentric loads.”J. Nat. Buildings Organization, Vol. 6, 66–78.
11.
Drescher, A., and Vardoulakis, I.(1982). “Geometric softening in triaxial tests on granular material.”Géotechnique, London, England, 32(4), 291–303.
12.
Eastwood, W. (1955). “The bearing capacity of eccentrically loaded foundations on sandy soils.”Struct. Engr., Vol. 33, 181–187.
13.
Feda, J. (1961). “Research on the bearing capacity of loose soil.”Proc., 5th Int. Conf. on Soil Mech. and Found. Engrg., Vol. I, 635–642.
14.
Fuglsang, L. D., and Ovesen, N. K. (1988). “The application of the theory of modeling to centrifuge studies.”Proc., Int. Conf. on Geotech. Centrifuge Modeling, Balkema, Rotterdam, The Netherlands, 119–138.
15.
Garnier, J., and Canepa, Y. (1991). “Effect of different footing conditions on the ultimate bearing pressure.”Proc., Centrifuge `91 Conf., Balkema, Rotterdam, The Netherlands.
16.
Hansen, J. B. (1970). “A revised and extended formula for bearing capacity.”Bull. No. 28, Danish Geotech. Inst., Copenhagen, Denmark, 5–11.
17.
Hettler, A., and Gudehus, G.(1988). “Influence of the foundation width on the bearing capacity factors.”Soils and Found., 28(4), 81–92.
18.
Ingra, T. S., and Baecher, G. B.(1983). “Uncertainty in bearing capacity of sands.”J. Geotech. Div., ASCE, 109(7), 899–914.
19.
Kimura, T., Kusakabe, O., and Saitoh, K.(1985). “Geotechnical model tests of bearing capacity problems in a centrifuge.”Géotechnique, London, England, 35(1), 33–45.
20.
Ko, H. Y. (1988). “Summary of the state-of-the-art in centrifuge model testing.”Centrifuge in soil mechanics, Craig, James, and Schofield, eds., Balkema Publishers, The Netherlands, 11–18.
21.
Ko, H. Y., and Davidson, L. W.(1973). “Bearing capacity of footings in plane strain.”J. Soil Mech. and Found. Div., ASCE, 99(1), 1–23.
22.
Lade, P. V., and Lee, K. L. (1976). “Engineering properties of soils.”Rep., UCLA-ENG-7652, Univ. of California, Los Angeles.
23.
Lee, I. K. (1965). “Footings subjected to moments.”Proc., 6th Int. Conf. on Soil Mech. and Found. Eng., ICSMFE, Vol. II, 108–112.
24.
Lee, K. L.(1970). “Comparison of plane strain and triaxial tests on sand.”J. Soil Mech. and Found. Div., ASCE, 96(3), 901–923.
25.
Marachi, N. D., Duncan, J. M., Chan, C. K., and Seed, H. B. (1981). “Plane-strain testing of sand.”Laboratory shear strength of soil; ASTM STP 740, R. N. Yong and F. C. Townsend, eds., Am. Soc. of Testing and Mat. (ASTM), Philadelphia, Pa., 294–302.
26.
Meyerhof, G. G. (1948). “An investigation of the bearing capacity of shallow footings on dry sand.”Proc., 2nd Int. Conf. on Soil Mech. and Found. Engrg., ICSMFE, Vol. I, 237–243.
27.
Meyerhof, G. G. (1951). “The ultimate bearing capacity of foundations.”Géotechnique, London, England, Vol. 2, 301–332.
28.
Meyerhof, G. G. (1953). “The bearing capacity of foundations under eccentric and inclined loads.”Proc., 3rd Int. Conf. on Soil Mech. and Found. Engrg., ICSMFE, Vol. I, 440–445.
29.
Meyerhof, G. G.(1955). “The influence of roughness of base and ground water conditions on the ultimate bearing capacity of foundations.”Géotechnique, London, England, 5(3), 227–242.
30.
Mikasa, M., and Takada, N. (1973). “Significance of centrifugal model test in soil mechanics.”Proc., 8th Int. Conf. on Soil Mech. and Found. Engrg., ICSMFE, Vol. 1.2, 273–278.
31.
Milović, D. M. (1965). “Comparison between the calculated and experimental value of the ultimate bearing capacity.”Proc., 6th Int. Conf. Soil Mech. and Found. Engrg., Vol. II, 142–144.
32.
Muhs, H. (1965). “Comparison between the calculated and experimental value of the ultimate bearing capacity; Discussion.”Proc., 6th Int. Conf. on Soil Mech. and Found. Engrg., ICSMFE, Vol. III, 439–440.
33.
Muhs, H., and Weiss, K. (1973). “Inclined load tests on shallow strip footings.”Proc., 8th Int. Conf. on Soil Mech. and Found. Engrg., ICSMFE, Vol. I, 173–179.
34.
Ovesen, N. K.(1975). “Centrifuge testing applied to bearing capacity problems of footings on sands.”Géotechnique, London, England, 25(2), 394–401.
35.
Ovesen, N. K. (1979). “The scaling law relationship; Panel discussion.”Proc., 7th European Conf. on Soil Mech. and Found. Engrg., British Geotech. Soc., Vol. V, 319–323.
36.
Prakash, S., and Saran, S.(1971). “Bearing capacity of eccentrically loaded footings.”J. Soil Mech. and Found. Div., ASCE, 97(1), 95–117.
37.
Pu, J. L., and Ko, H. Y. (1988). “Experimental determination of bearing capacity in sand by centrifuge footing tests.”Proc., Int. Conf. on Geotech. Centrifuge Modeling, Balkema, Rotterdam, The Netherlands, 293–299.
38.
Scott, R. F. (1988). “Physical and numerical models.”Centrifuge in soil mechanics, Craig, James, and Schofield, eds., Balkema Publishers, The Netherlands, 103–117.
39.
Steenfelt, J. S. (1977). “Scale effect on bearing capacity factor N γ .”Proc., 9th Int. Conf. on Soil Mech. and Found. Engrg., Vol. I, 745–752.
40.
Vesić, A. S. (1975). “Chapter 3: bearing capacity of shallow foundations.”Foundation engineering handbook. Van Nostrand Reinhold Book Co., New York, N.Y.
41.
Yamaguchi, H., Kimura, T., and Fujii, N.(1976). “On the influence of progressive failure on the bearing capacity of shallow foundations in dense sand.”Soils and Found., 16(4), 11–22.
42.
Yamaguchi, H., Kimura, T., and Fujii, N. (1977). “On the scale effect of footings on dense sand.”Proc., 9th Int. Conf. on Soil Mech. and Found. Engrg., ICSMFE, Vol. I, 795–798.
43.
Zaharescu, F. (1961). “The eccentricity sense influence of inclined loads on the bearing capacity of rigid foundations.”J. Nat. Buildings Organization, Vol. 6, 282–293.
Information & Authors
Information
Published In
Journal of Geotechnical Engineering
Volume 121 • Issue 10 • October 1995
Pages: 704 - 712
Copyright
Copyright © 1995 American Society of Civil Engineers.
History
Published online: Oct 1, 1995
Published in print: Oct 1995
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.