Postdensification Penetration Resistance of Clean Sands
Publication: Journal of Geotechnical Engineering
Volume 116, Issue 7
Abstract
Freshly consolidated or densified clean sands exhibit a substantial increase in stiffness under drained aging conditions. Laboratory measurements of dynamic shear modulus after primary consolidation and field measurements of penetration resistance after ground densification by blasting, vibrocompaction, or dynamic compaction, in clean sands show a significant increase with time. A possible mechanism for this time effect in clean sands is the continued rearrangement of sand particles during secondary compression. Improved frictional resistance to deformation develops with time with a gradual increase in interlocking of particle surface roughness and increased geometrical particle interference through more efficient packing. Empirical equations are proposed that result in satisfactory predictions of the postprimary consolidation shear modulus and of postdensificatibn cone‐penetration resistance. The equation for the time‐dependent cone resistance includes the assumption of a decrease in compressibility and an increase in effective horizontal stress during secondary compression. In the absence of continued cone‐penetration testing subsequent to compaction, the proposed equation may be used to extrapolate from measurements that are carried out immediately after ground modification.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Al‐Saleh, S., and Khalaf, F. J. (1982). “Surface textures of quartz grains from various recent sedimentary environments in Kuwait.” J. of Sedimentary Petrology, 52(1), 215–225.
2.
Anderson, D. G., and Stokoe, K. H., II (1978). “Shear modulus, a time‐dependent soil property.” Dynamic Geotech. Testing (ASTM STP 654), 66–90.
3.
Blümel, W., and Lackner, F. (1981). “Performance of foundations for masts on sand.” Proc. 10th Int. Conf. on Soil Mech. and Foundation Engrg., International Society of Soil Mechanics and Foundation Engineering, 2, 49–52.
4.
Casagrande, A., and Fadum, R. E. (1940). “Notes on soil testing for engineering purposes.” Harvard Soil Mech. Series No. 8, Cambridge, Mass.
5.
Castro, G. (1969). “Liquefaction of sands.” Harvard Soil Mech. Series No. 81, Cambridge, Mass.
6.
Daramola, O. (1980). “Effect of consolidation age on stiffness of sand.” Geotechnique, 30(2), 213–216.
7.
Davisson, M. T., and Salley, J. R. (1972). “Settlement histories of four large tanks on sand.” Proc. of the Specialty Conf. on Performance of Earth and Earth‐Supported Structures, ASCE, 1, Part 2, 981–996.
8.
Dowding, C. H., and Hryciw, R. D. (1986). “A laboratory study of blast densification of saturated sand.” J. Geotech. Engrg., ASCE, 112(2), 187–199.
9.
Hansen, B. (1961). “The bearing capacity of sand, tested by loading circular plates.” Proc. of the 5th Int. Conf. on Soil Mech. and Foundation Engrg., International Society of Soil Mechanics and Foundation Engineering, 1, 659–664.
10.
Hardin, B. O., and Black, W. L. (1968). “Vibration modulus of normally consolidated clay.” J. Soil Mech. and Found. Engrg. Div., ASCE, 94(2), 353–368.
11.
Henderson, J. H., Syers, J. K., and Jackson, M. L. (1970). “Quartz dissolution as influenced by pH and the presence of a disturbed surface layer.” Isr. J. Chemistry, 8, 357–372.
12.
Houlsby, G. T., and Hitchman, R. (1988). “Calibration chamber tests of a cone penetrometer in sand.” Geotechnique, 38(1), 39–44.
13.
Meigh, A. C. (1987). “Cone penetration testing.” CIRIA ground engineering report: In situ testing, Butterworth Publishers, Stoneham, Mass.
14.
Meigh, A. C., and Nixon, J. K. (1961). “Comparison of in situ tests for granular soils.” Proc., 5th Int. Conf. on Soil Mech. and Foundation Engrg., International Society of Soil Mechanics and Foundation Engineering, 1, 499–507.
15.
Mesri, G., and Castro, A. (1987). “ concept and during secondary compression.” J. Geotech. Engrg., ASCE, 113(3), 230–247.
16.
Mesri, G., and Choi, Y. K. (1983). “Discussion of dynamic properties of soft clays for wide strain range,” by T. Kokusho, Y. Yoshida, and Y. Esashi. Soils Found., 23(1), 125–127.
17.
Mesri, G., and Godlewski, P. M. (1977). “Time‐ and stress‐compressibility interrelationship.” J. Geotech. Engrg. Div., ASCE, 103(5), 417–430.
18.
Mitchell, J. K. (1986a). “Practical problems from surprising soil behavior.” J. Geotech. Engrg., ASCE, 112(3), 255–289.
19.
Mitchell, J. K. (1986b). “Ground improvement evaluation by in‐situ tests.” Proc. of In Situ '86, (Geotechnical Special Publication No. 6), ASCE, 221–236.
20.
Mitchell, J. K., and Solymar, Z. V. (1984). “Time‐dependent strength gain in freshly deposited or densified sand.” J. Geotech. Engrg., ASCE, 110(11), 1559–1576.
21.
Nonveiler, E. (1963). “Settlement of a grain silo on fine sand.” Proc. of the 3rd European Conf. on Soil Mech. and Found. Engrg., European Society of Soil Mechanics and Foundation Engineering, 1, 285–294.
22.
Oteo, C. S. (1983). “Prediction of settlement after deep vibration in granular fills.” Proc. of the 8th European Conf. on Soil Mech. and Found. Engrg., Helsinki, 1, 283–287.
23.
Parkin, A. K. (1977). “The compression of rockfill.” Proc., Aust. Geomech. J., 7, 33–39.
24.
Schmertmann, J. H. (1974). “Penetration pore pressure effects on quasi‐static cone bearing, qc,” Proc., 1st European Symp. on Penetration Testing, European Society of Soil Mechanics and Foundation Engineering, 2.2, 345–351.
25.
Schmertmann, J. H. (1987). Discussion of “Time‐dependent strength in freshly deposited or densified sand,” by J. K. Mitchell and Z. V. Solymar. J. Geotech. Engrg., ASCE, 113(2), 173–175.
26.
Schmertmann, J. H., et al. (1986). “CPT/DMT QC of ground modification at a power plant.” Proc. of In Situ '86, (Geotechnical Special Publication No. 6), ASCE, 985–1001.
27.
Seed, H. B. (1979). “Soil liquefaction and cyclic mobility evaluation for level ground during earthquakes.” J. Geotech. Engrg. Div., ASCE, 105(2), 201–255.
28.
Solymar, Z. V. (1984). “Compaction of alluvial sands by deep blasting.” Can. Geotech. J., 21(2), 305–321.
29.
Solymar, Z. V., et al. (1984). “Earth foundation treatment at Jebba dam site.” J. Geotech. Engrg., ASCE, 110(10), 1415–1430.
30.
Sowers, G. F., Williams, R. C., and Wallace, T. S. (1965). “Compressibility of broken rock and the settlement of rockfills.” Proc., 6th Int. Conf. on Soil Mech. and Found. Engrg., International Society of Soil Mechanics and Foundation Engineering, 2, 561–565.
31.
Swiger, W. F. (1975). “Evaluation of soil moduli.” Proc. of the Conf. on Analysis and Design in Geotech. Engrg., ASCE, 2, 79–92.
32.
Terzaghi, K. (1934). “Large retaining‐wall tests.” Engrg. News‐Rec., 112, Feb. 1, 136–140.
33.
Terzaghi, K., and Peck, R. B. (1967). Soil mechanics in engineering practice. 2nd Ed., John Wiley and Sons, Inc., New York, N.Y.
34.
Trudeau, P. T., Whitman, R. V., and Christian, J. T. (1974). “Shear wave velocity and modulus of a marine clay.” J. Boston Soc. of Civ. Engrs., 61(1), 12–25.
35.
Veismanis, A. (1974). “Laboratory investigation of electrical friction‐cone penetrometers in sands.” Proc., 1st European Symp. on Penetration Testing, European Society of Soil Mechanics and Foundation Engineering, 2.2, 407–419.
36.
Whitman, R. V., Miller, E. T., and Moore, P. J. (1964). “Yielding and locking of confined sand.” J. Soil Mech. and Found. Engrg. Div., 90(4), 57–84.
Information & Authors
Information
Published In
Copyright
Copyright © 1990 ASCE.
History
Published online: Jul 1, 1990
Published in print: Jul 1990
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.