Sandwich‐Barrel Shell Construction by Inflation
Publication: Journal of Construction Engineering and Management
Volume 117, Issue 1
Abstract
Fabric‐reinforced mortar faces on expanded polystyrene (EPS) core structural sandwich construction is used for low‐cost quonset buildings. The construction, especially suitable for warehousing and agricultural buildings, consists of: (1) Laying polystyrene insulation boards on a flat surface; (2) stretching reinforcing fabric over the boards to keep them tightly abutted; (3) screeding a cement‐fly ash slurry containing styrene‐butadiene latex admixture through the fabric; (4) inflating a polyethylene film under the EPS boards thus joined to form them into an arch after the mortar hardens; and (5) tilting precut sandwich panel end walls up under the arch to support it. A cement mortar reinforced with polypropylene chopped fiber is then gunned inside the arch to complete the structural sandwich construction. Required cylindrical sandwich core and face thicknesses to resist buckling at minimum material cost are calculated. Material costs are tabulated. Flexural modulus is determined from panel‐bending tests. The flexural stiffness/dead weight ratios are compared with those ratios for precast prestressed concrete decks.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Alford, N. M. (1985). “Production of fibre‐reinforced cementitious composition.” U.S. Patent 4,528,238, U.S. Patent Office, Washington, D.C.
2.
Baker, E. H., Kovalevsky, L., and Rish, F. L. (1972). Structural analysis of shells. McGraw‐Hill, New York, N.Y.
3.
Handbook of structural stability. (1971). Corona Publishers, Tokyo, Japan.
4.
Hannant, D. J. (1978). Fibre cements and fibre concretes. John Wiley and Sons, New York, N.Y.
5.
Hartsock, J. A. (1969). Design of foam‐filled structures. Technomic Publishing Co., Lancaster, Pa.
6.
Heger, F. J. (1966). “Design of reinforced plastic shell structures.” Plastics in building, I. Skeist, ed., Reinhold Publishing Co., New York, N.Y.
7.
Heger, F. J., ed. (1982). “Thin rings and shells.” Structural plastics design manual, ASCE, New York, N.Y., 9‐1–9‐172.
8.
Krenchel, H. (1964). Fiber reinforcement. Akademisk Forlag, Copenhagen, Denmark.
9.
Nicholls, R. (1976). Composite construction materials. Prentice‐Hall, Englewood Cliffs, N.J., 463.
10.
Nicholls, R. (1990). “Fabric‐reinforced mortar faces on EPS core sandwich construction of quonset buildings.” Proc. First Int. Symp. Textile Composites in Building Constr., Part 1, Cement‐Based Composites, P. Hamelin and G. Verchery, eds., Forum International des Technologies Apliquees du Textile.
11.
Nicholls, R., and Hernson, D. (1987). “Nonwoven fabric‐reinforced cement shingles and tile: Cross section optimization.” Proc. 15th Ann. Tech. Symp., Association of Nonwoven Fabrics Industry, May, 410–438.
12.
Nicholls, R., and Karbhari, V. (1989a). “Non‐destructive load predictions of concrete shell buckling.” J. Struct. Engrg., ASCE, 115(5), 1191–1211.
13.
Nicholls, R., and Karbhari, V. (1989b). “Fold and bond construction of cement laminate structural shapes.” J. Mater. in Civ. Engrg., ASCE, 1(3), 133–151.
14.
Plantema, F. J. (1966). Sandwich construction. John Wiley and Sons, Inc., New York, N.Y.
15.
Schupack, M. (1986). “Three dimensionally reinforced fabric concrete.” U.S. Patent 4,617,219, U.S. Patent Office, Washington, D.C.
16.
Swamy, R. N., ed. (1984). New reinforced concretes. Surry University Press, London, England.
Information & Authors
Information
Published In
Copyright
Copyright © 1991 ASCE.
History
Published online: Mar 1, 1991
Published in print: Mar 1991
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.