International Journal of Geomechanics

Neural network (NN) models for time series forecasting were initially used in economic fields. In this paper, NN models for time series forecasting are introduced for use in forecasting the settlement of chimney foundations. The data sets used in the NN models were measured in the field. Seven models with different input series are developed to determine the optimal structure of the network. In evaluating the network performance, the network model that uses the previous nine months’ settlement values as input is selected as the optimal model. The analysis results demonstrate that the settlement values predicted by the optimal model are in good agreement with the field measurements. In addition, as the number of data points in the input series increases, the NN performance clearly improves, and this improvement stops after the input series has increased to a certain extent. This demonstrates that the time-series-based NN model can also be successfully applied to predict foundation settlement.

Pile-soil interaction in an expansive soil foundation has been primarily analyzed by an analytical solution in our previous study. As a complementary work, this paper briefly reviews the derivation process in more detail and extends the capability of the solution in dealing with the pile-soil interaction issue under various conditions. The results show that (1) increasing pile length is able to effectively decrease the upward pile movements, but meanwhile, the tensile stresses along the pile shaft increase as well; (2) a critical pile diameter exists ($d\approx 0.04L$); (3) when the diameter is less than this value, the upward pile movements can be reasonably reduced, but for the pile with a larger diameter, it has little effect on reducing the upward pile movements, and as irrigation proceeds, both the displacements and tensile stresses increase and both tend to be much less sensitive to the water’s incoming over time; and (4) a critical applied pressure for preventing the upward pile movements that is induced by soil’s swelling pressure is found to be 2.5 times of the maximum tensile stress of the free pile only under swelling pressure in expansive soil foundation.

A centrifuge test was performed on a reinforced embankment backfilled with lime-stabilized soil on soft clay installed with wick drains. The finite-element program PLAXIS was employed to simulate the centrifuge test on the basis of the test dimensions. Verifications of the numerical model were taken by comparing the numerical results with the measurements obtained from the centrifuge test, and it was found that both were in good agreement. Three cases of unreinforced, one-layer reinforced, and two-layer reinforced embankments were simulated and compared on the basis of the numerical model. A centrifuge similarity drainage relationship was also proposed in this paper on the basis of the equal degree of consolidation between the model and prototype drains.

Over the past six decades, significant attention has been paid to the elastoplastic behavior of unsaturated soils. In the past two decades alone, elastoplastic theory for unsaturated soils has been established and experimental techniques for measuring the elastoplastic behavior of unsaturated soils have become more sophisticated. However, less effort has been directed at developing the best strategy for constitutive modeling of unsaturated soils. At present, there is no standard method for developing constitutive models for unsaturated soils from experimental data, and owing to the extreme complexity of unsaturated soil behavior, there are limitations in the existing modeling methods. If these limitations are not recognized, misleading results in the constitutive modeling of unsaturated soil behavior may occur. This paper discusses the origins of and possible solutions to these limitations. Experimental data from the recent literature are used to demonstrate the use of existing methods for the constitutive modeling of unsaturated soils and potential associated problems. A modified state-surface approach (MSSA), recently proposed to model the elastoplastic behavior of unsaturated soils under isotropic conditions, was applied to overcome the limitations and develop a constitutive model that can best represent the behavior of unsaturated soil. A comparison of the proposed method and existing methods is discussed, and from this discussion, the capability and effectiveness of the proposed method are evaluated.

The mechanical characteristics of rock masses anchored with bolts play a critical role in anchored slope and underground buildings. In this study, the components and their mixing ratios of similar materials, such as rock masses, are simulated. The materials similar to the anchored bolts and cement are selected. The physical and mechanic properties of these materials are tested. Based on these, an experimental model and a method are designed with a focus on a uniaxial compression test on anchored rock masses. A series of tests on the anchored specimens’ uniaxial compression strength are conducted under the conditions of varying numbers and installations of anchor bolts. The results reveal that compared with the specimens without anchor bolts, the peak strength, elastic modulus, and shear strength of the specimens with both perpendicular and horizontal bolts are improved. Furthermore, it is indicated that the improvement attributable to the horizontal bolts is slightly lower than that with vertical bolts. This suggests that the uniaxial compression strength is heterogeneous in different directions.

The ultimate pullout capacity (UPC) and the shape modification factors of horizontal plate anchors were calculated by using upper-bound limit analysis, in which the assumptions of both a nonlinear failure criterion and the nonassociated flow rule were made upon the soil mass above the anchor plate. Three types of anchor plates, including strip anchors, circle anchors, and rectangle anchors, and the corresponding failure mechanisms are taken into consideration. The anchor breakout factors were obtained according to the principle of virtual power, which was realized numerically by the nonlinear sequential quadratic programming algorithm. The shape modification factors for different kinds of anchors were given through a multiple nonlinear regression method. Numerical experiments demonstrate the validity of the solutions by reducing the solutions (nonlinear criterion and nonassociated flow rule) into their special cases (linear criterion and associated flow rule), which matches well with existing work. The dilation and nonlinearity of soil mass should be considered because it plays a remarkable role in the UPC of anchor plates.

This paper presents the results of an elastoplastic finite-element back analysis of an excavation made on a saturated soft organic clay deposit in Rio de Janeiro, Brazil. The excavation was conducted as part of an urbanization program, in which artificial islands were to be created in a swamp along the margins of the Camboinhas Lagoon. An extensive laboratory testing program was performed on undisturbed soil samples to characterize the stress-strain-strength behavior of the involved materials. Results from this laboratory testing program were used to calibrate a nonassociated elastoplastic constitutive model implemented in the ANLOG (Nonlinear Analysis of Geotechnical Problems) code. This code is based on the finite-element method and is capable of conducting fully coupled analyses by using a variety of constitutive models. Coupled analyses were performed to simulate the Camboinhas excavation, which was conducted under plane strain condition. Field measurements of both displacements and pore-water pressures obtained during the excavation are compared with the results of the numerical simulation. Analyses of the results show that monitored in situ and numerical results are in good agreement.

In this paper a theoretical study of the behavior of structured soils, including both clays and sands, is presented. A new model, which is referred to as the “Sydney soil model,” is formulated within the framework of critical state soil mechanics. In the proposed model, the mechanical behavior of soil is divided into two parts, that at a reference state and that attributed to the influence of soil structure. The reference state behavior is formulated according to the soil properties at the critical state of deformation, based on the concept of plastic volumetric hardening. The effects of structure are captured in the model by incorporation of the additional voids ratio that arises owing to the presence of soil structure. The formulation is generalized to include both isotropic compression and general shearing. In part I of this paper, a new theoretical framework for modeling structured soil behavior and the formulation of the proposed Sydney soil model are introduced. In part II of this paper, the Sydney soil model is employed to simulate the behavior of clays and sands, including calcareous clays and sands subjected to both drained and undrained shearing, and the performance of the model is evaluated.

This paper presents simulations of the mechanical behavior of reconstituted and natural soils using a new model presented in a companion paper and referred to as the “Sydney soil model.” It is demonstrated that the performance of the proposed model is essentially the same as that of modified Cam clay model when describing the behavior of clays in laboratory reconstituted states. The model has also been employed to simulate the drained and undrained behavior of structured clays and sands, including calcareous clay and sand. Five sets of conventional triaxial tests and one set of true triaxial tests have been considered. It is demonstrated that the new model provides satisfactory qualitative and quantitative modeling of many important features of the behavior of structured soils, particularly in capturing various patterns of the stress and strain behavior associated with soil type and structure. A general discussion of the model parameters is also included. It is concluded that the Sydney soil model is suitable for representing the behavior of many soils if their ultimate state during shearing can be defined by an intrinsic and constant stress ratio $M^{*}$ and a unique relationship between mean effective stress and voids ratio, i.e., a unique $p^{\prime }-e$ curve.

The reinforcement of soft soils by rigid inclusions is a practical and economical technique for wide-span buildings and the foundations of embankments. This method consists of placing a granular layer at the top of the network of piles to reduce vertical load on the supporting soil and vertical settlement of the upper structure. The study focuses on the modeling of load-transfer mechanisms occurring in the reinforced structure located over the network of piles with a coupling between the finite-element method (geosynthetic sheets) and discrete element method (granular layer; concrete slab in some cases). The importance of granular layer thickness to increase load-transfer intensity and to reduce vertical settlement was observed. However, without a basal geosynthetic sheet, the compressibility of soft soil has a great influence on the mechanisms. A method predicting the intensity of load transfers was proposed, based on Carlsson’s solution. The main parameters concerned are the geometry of the work and the peak and residual friction angles of the granular layer.

The strengths of geomaterials and their variation under different factors are investigated in this paper. First, a general isotropic variation of a strength criterion is proposed for describing the critical state and peak strengths of geomaterials. Second, the proposed criterion is extended to describe the effect of anisotropy on the peak strength. After an analysis of experimental data, the hypothesis is made that the failure of an element of geomaterial generally occurs in a particular plane when the applied shear stress in that plane reaches the shear resistance of the material. Therefore, the variation of the peak strength of anisotropic materials should be described in terms of the stress tensor applied, a vector parameter defining the position of the potential failure plane of the material, and the material properties. A general failure criterion for geomaterials with cross anisotropy is obtained then from the proposed isotropic strength criterion. The proposed criterion is demonstrated to well represent both the isotropic and anisotropic strengths of various geomaterials. Finally, a general anisotropic criterion is introduced.