An Innovative Way to Repair Damaged Concrete Floors Using Epoxy Adhesives: A Case Study of Its Technical Assessment and Renovation
Publication: Practice Periodical on Structural Design and Construction
Volume 28, Issue 2
Abstract
This case study describes an evaluation of the existing conditions of a concrete floor in an industrial hall located in Poland. The areas requiring improvement due to poor workmanship, as well as the age of the floor, were identified. The second part of the study is devoted to the procedure of making an innovative epoxy coating modified with granite powder, which is based on the authors’ previously published research. The analysis describes the effects of adding 10% to 60% (graded every 10%) of the powder. The primary aim of the tests was to obtain the highest possible pull-off strength. Compared to the reference sample, the highest increase in strength, 18%, was obtained with the addition of 20% granite powder. Moreover, resistance to thermal shock, one of the most important parameters of epoxy floors, was also analyzed and discussed. Standard coatings are typically not resistant to thermal shock, but the innovative coating proposed in this study allows for increased resistance by up to several dozen percent. The relationship between the amount of granite powder added and the limit value of thermal shock resistance is presented in the article. The novelty of the case study involves the proposal of a comprehensive procedure of renovating floors, including the assessment of their condition, the repair methods, their surface strengthening, and the presentation of the characteristics of the new coating.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
The data, models, or codes that support the findings of this study are available from the corresponding author upon request.
Acknowledgments
The authors express their thanks to Adrian Chajec and Mateusz Moj for their help in the preparation of the concrete slab and the implementation of the resin coatings. The authors received funding from the project supported by the National Centre for Research and Development, Poland - Grant No. LIDER/35/0130/L-11/19/NCBR/2020 “The use of granite powder waste for the production of selected construction products.”
References
Ahn, N. 2003. “Effects of diacrylate monomers on the bond strength of polymer concrete to wet substrates.” J. Appl. Polym. Sci. 90 (4): 991–1000. https://doi.org/10.1002/app.12723.
Alwash, D., R. Kalfat, H. Du, and R. Al-Mahaidi. 2021. “Development of a new nano modified cement based adhesive for FRP strengthened RC members.” Constr. Build. Mater. 277 (Mar): 122318. https://doi.org/10.1016/j.conbuildmat.2021.122318.
ASTM. 2017 Standard test method for pull-off strength of coatings using portable adhesion testers. ASTM D4541-17. West Conshohocken, PA: ASTM.
Carbas, R. J. C., E. A. S. Marques, L. F. M. Da Silva, and A. M. Lopes. 2014. “Effect of cure temperature on the glass transition temperature and mechanical properties of epoxy adhesives.” J. Adhes. 90 (1): 104–119. https://doi.org/10.1080/00218464.2013.779559.
Chajec, A. 2021. “Granite powder vs. fly ash for the sustainable production of air-cured, cementitious mortars.” Materials (Basel) 14 (5): 1208. https://doi.org/10.3390/ma14051208.
Chajec, A., Ł. Sadowski, and M. Moj. 2021. “The adhesive and functional properties of cementitious overlays modified with granite powder.” Int. J. Adhes. Adhes. 117 (Sep): 103008. https://doi.org/10.1016/j.ijadhadh.2021.103008.
Chen, C., G. Habert, Y. Bouzidi, and A. Jullien. 2010. “Environmental impact of cement production: Detail of the different processes and cement plant variability evaluation.” J. Cleaner Prod. 18 (5): 478–485. https://doi.org/10.1016/j.jclepro.2009.12.014.
Chowaniec, A. 2021a. “The effect of the viscosity and the contact angle on the pull-off strength of epoxy resin modified with waste granite powders.” In Proc., 6th Int. Conf. on Adhesive Bonding 2021, 83–102. Cham, Switzerland: Springer.
Chowaniec, A. 2021b. “Using waste limestone powder as filler in a toxic epoxy resin coating and its influence on adhesive properties.” Chem. Eng. Trans. 88 (2021): 1063–1068. https://doi.org/10.3303/CET2188177.
Chowaniec, A., and K. Ostrowski. 2018. “Epoxy resin coatings modified with waste glass powder for sustainable construction.” Tech. Trans. 115 (8): 99–109. https://doi.org/10.4467/2353737XCT.18.118.8893.
Chowaniec, A., Ł. Sadowski, and A. Żak. 2019. “The chemical and microstructural analysis of the adhesive properties of epoxy resin coatings modified using waste glass powder.” Appl. Surf. Sci. 504 (Feb): 144373. https://doi.org/10.1016/j.apsusc.2019.144373.
Dębska, B., L. Lichołai, and P. Miąsik. 2019. “Assessment of the applicability of sustainable epoxy composites containing waste rubber aggregates in buildings.” Buildings 9 (2): 31. https://doi.org/10.3390/buildings9020031.
Do, J., and Y. Soh. 2003. “Performance of polymer-modified self-leveling mortars with high polymer–cement ratio for floor finishing.” Cem. Concr. Res. 33 (10): 1497–1505. https://doi.org/10.1016/S0008-8846(02)01057-8.
Doliński, Ł. 2013. “Damage localisation in a stiffened plate structure using a propagating wave.” Mech. Syst. Sig. Process. 39 (1–2): 388–395. https://doi.org/10.1016/j.ymssp.2013.02.014.
Dziubak, C., and W. M. Rećko. 2009. “Thermal shock in ceramics. Th. 1. Modern theories of heat shock (PL).” In Vol. 2 of Works of the institute of glass, ceramics, refractory and building materials, 9–28. Opole, Poland: Wydawnictwo Instytut Śląski Sp. z o.o.
Fawzy, K., and M. A. Farouk. 2022. “Enhanced repair techniques of corroded reinforced concrete short columns.” Pract. Period. Struct. Des. Constr. 27 (2): 04021084. https://doi.org/10.1061/(ASCE)SC.1943-5576.0000669.
Hao, Y., F. Liu, H. Shi, E. Han, and Z. Wang. 2011. “The influence of ultra-fine glass fibers on the mechanical and anticorrosion properties of epoxy coatings.” Prog. Org. Coat. 71 (2): 188–197. https://doi.org/10.1016/j.porgcoat.2011.02.012.
ISO. 2017. Building components and building elements—Thermal resistance and thermal transmittance—Calculation method. ISO 6946. Warsaw, Poland: Polish Committee for Standardisation.
Kampa, Ł., A. Chowaniec, A. Królicka, and Ł. Sadowski. 2020. “The effect of the addition of polypropylene fibers to primer on the pull-off strength of epoxy resin coatings.” Materials (Basel) 13 (20): 4674. https://doi.org/10.3390/ma13204674.
Kampa, Ł., A. Chowaniec, A. Królicka, and Ł. Sadowski. 2022. “Adhesive properties of an epoxy resin bonding agent modified with waste granite powder.” J. Coat. Technol. Res. 19 (5): 1303–1316. https://doi.org/10.1007/s11998-022-00620-2.
Kampa Ł., and Ł. Sadowski. 2021. “Engineering technology and preparation of coating systems made with epoxy resin-based bonding agents modified with the addition of granite powder sourced from quarry wastes.” In Proc., 6th Int. Conf. on Adhesive Bonding 2021, edited by L. F. M. da Silva and R. D. Adams. Cham, Switzerland: Springer.
Kampa, Ł., Ł. Sadowski, and A. Królicka. 2021. “The use of synthetic and natural fibers in epoxy coatings: A comparative mechanical and economic analysis.” Int. J. Adhes. Adhes. 117 (Sep): 103017. https://doi.org/10.1016/j.ijadhadh.2021.103017.
Krzywiński, K., Ł. Sadowski, D. Stefaniuk, A. Obrosov, and S. Weiß. 2021a. “Engineering and manufacturing technology of green epoxy resin coatings modified with recycled, fine aggregates.” Int. J. Precis. Eng. Manuf.-Green Technol. 9 (1): 253–271. https://doi.org/10.1007/s40684-021-00377-w.
Krzywiński, K., A. Sieradzki, Ł. Sadowski, A. Królicka, and C. Chastre. 2021b. “Thermal wear of epoxy composite modified with rutile titanium dioxide.” Compos. Struct. 282 (Feb): 115127. https://doi.org/10.1016/j.compstruct.2021.115127.
Li, Y., X. Liu, and J. Li. 2017. “Experimental study of retrofitted cracked Concrete with FRP and nanomodified epoxy resin.” J. Mater. Civ. Eng. 29 (5): 04016275. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001810.
Othman, N. H., W. Z. N. Yahya, and I. M. Che. 2020. “Highly dispersed graphene oxide–zinc oxide nanohybrids in epoxy coating with improved water barrier properties and corrosion resistance.” J. Coat. Technol. Res. 17 (1): 101–114. https://doi.org/10.1007/s11998-019-00245-y.
PN-EN. 2003. Building materials and products—Thermal and humidity properties—Tabulated calculation values. PN-EN 12524. Opole, Poland: Wydawnictwo Instytut Śląski Sp. z o.o.
Qiu, J., M. Zhu, Y. Zhou, and X. Guan. 2021. “Effect and mechanism of coal gangue concrete modification by fly ash.” Constr. Build. Mater. 294 (Aug): 123563. https://doi.org/10.1016/j.conbuildmat.2021.123563.
Rootzen, J., and F. Johansson. 2014. “Managing the costs of abatement in the cement industry.” Clim. Policy 17 (6): 781–800. https://doi.org/10.1080/14693062.2016.1191007.
Rousakisa, T., K. Kouraveloub, and T. Karachaliosb. 2013. “Effects of carbon nanotube enrichment of epoxy resins on hybrid FRP–FR confinement of concrete.” Composites, Part B 57 (Feb): 210–218. https://doi.org/10.1016/j.compositesb.2013.09.044.
Sadowski, Ł., J. Hoła, A. Żak, and A. Chowaniec. 2020. “Microstructural and mechanical assessment of the causes of failure of floors made of polyurethane-cement composites.” Compos. Struct. 238 (Apr): 112002. https://doi.org/10.1016/j.compstruct.2020.112002.
Sadowski, Ł., Ł. Kampa, A. Chowaniec, A. Królicka, A. Żak, H. Abdoulpour, and S. Vantadori. 2021. “Enhanced adhesive performance of epoxy resin coating by a novel bonding agent.” Constr. Build. Mater. 301 (Sep): 124078. https://doi.org/10.1016/j.conbuildmat.2021.124078.
Wang, S., Q. Li, W. Zhang, and H. Zhou. 2002. “Crack resistance test of epoxy resin under thermal shock.” Polym. Test. 21 (2): 195–199. https://doi.org/10.1016/S0142-9418(01)00069-1.
Yang, X., X. Wang, W. Wang, Y. Fu, and Q. Xie. 2020. “Atomic-scale insights into interface thermal resistance between epoxy and boron nitride in nanocomposites.” Int. J. Heat Mass Transfer 159 (Oct): 120105. https://doi.org/10.1016/j.ijheatmasstransfer.2020.120105.
Information & Authors
Information
Published In
Copyright
© 2023 American Society of Civil Engineers.
History
Received: May 20, 2022
Accepted: Nov 17, 2022
Published online: Jan 18, 2023
Published in print: May 1, 2023
Discussion open until: Jun 18, 2023
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.