New Geometric Design Approach to Reduce Vehicle’s Speed in Accident-Prone Downgrade Highways Using Dynamic Vehicle Modeling
Publication: Journal of Transportation Engineering, Part A: Systems
Volume 147, Issue 1
Abstract
Steep downgrades are known as a part of mountain roads with a significant number of severe crashes. Generally, using speed limiters such as speed bumps and speed humps are considered the most effective (considering both the time and cost) ways to reduce the number of victims. The efficiency of speed limiters depends on the driver’s consciousness and the car’s braking system; the latter could be problematic in wet and dark conditions of the road. The main goal of the current study is to propose an approach to correct the longitudinal profile of roads by replacing the consecutive downgrades and upgrades with a continuous downgrade. The vehicle’s speed is reduced by using this method before entering an accident-prone site without the driver’s involvement and breaking. To this end, a well-known software program is used under two speeds (70 and ) in 68 different routes to analyze speed along the proposed routes. Also, another computer model is used for dynamic simulation. Dynamic analyses and regression models show that the vehicle’s speed in the new proposed route is significantly reduced compared with the continuous downgrade. Moreover, results indicate that the upgrade slope of the proposed route has the most impact on reducing the final speed of the vehicles.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
References
AASHTO. 2010. Highway safety manual. 1st ed. Washington, DC: AASHTO.
AASHTO. 2018. A policy on geometric design of highways and streets. 7th ed. Washington, DC: AASHTO.
Ahmed, M., H. Huang, M. Abdel-Aty, and B. Guevara. 2011. “Exploring a Bayesian hierarchical approach for developing safety performance functions for a mountainous freeway.” Accid. Anal. Prev. 43 (4): 1581–1589. https://doi.org/10.1016/j.aap.2011.03.021.
Bonneson, J. A. 2000. Super elevation distribution methods and transition designs. Washington, DC: Transportation Research Board.
Brilon, W., and A. Bressler. 2004. Traffic flow on freeway upgrades. Washington, DC: National Research Council.
Ding, H., X. Zhao, J. Rong, and J. Ma. 2013. “Experimental research on the effectiveness of speed reduction markings based on driving simulation: A case study.” Accid. Anal. Prev. 60 (Nov): 211–218. https://doi.org/10.1016/j.aap.2013.08.007.
Dunn, A. L. 2003. Jackknife stability of articulated tractor semitrailer vehicles with high-output brakes and jackknife detection on low coefficient surfaces. Columbus, OH: Ohio State Univ.
Federal Motor Carrier Safety Administration. 2006. Report to congress on the large truck crash causation study. Washington, DC: Federal Motor Carrier Safety Administration.
Gillespie Thomas, D. 1992. Fundamentals of vehicle dynamics. Warrendale, PA: Society of Automotive Engineers International.
Goni Ros, B., L. Knoop, and V. Van Arem. 2012. “Reducing congestion at uphill freeway sections by means of a gradient compensation system.” In Proc., Intelligent Vehicles Symp., 191–198. New York: IEEE.
Goni Ros, B., V. L. Knoop, B. Van Arem, and S. P. Hoogendoorn. 2013. “Modeling driving behavior and traffic flow at sags.” In Proc., 20th ITS World Congress, 14–18. Tokyo: Intelligent Transportation System.
Iran Highway Geometric Design Code. 2012. Vice Presidency for strategic planning and supervision. Tehran, Iran: Ministry of Roads and Urban Development.
Kontaratos, M., B. Psarianos, and A. Yotis. 1994. Minimum horizontal curve radius as function of grade incurred by vehicle motion in driving mode. Washington, DC: Transportation Research Record.
Kordani, A. A., and A. M. Molan. 2015. “The effect of combined horizontal curve and longitudinal grade on side friction factors.” KSCE J. Civ. Eng. 19 (1): 303–310. https://doi.org/10.1007/s12205-013-0453-3.
Ma, X., F. Chen, and S. Chen. 2015. “Modeling crash rates for a mountainous highway by using refined-scale panel data.” Transp. Res. Rec. 2515 (1): 10–16. https://doi.org/10.3141/2515-02.
MacAdam, C. C., P. S. Fancher, and L. Segel. 1985. Side friction for super elevation on horizontal curves. Ann Arbor, MI: Univ. of Michigan.
NCHRP (National Cooperative Highway Research Program). 2008. Guidelines for selection of speed reduction treatments at high-speed intersections. NCHRP Rep. 613. Washington, DC: Transportation Research Board.
NCHRP (National Cooperative Highway Research Program). 2011. Speed reduction techniques for rural high-to-low speed transitions. NCHRP Rep. 412. Washington, DC: Transportation Research Board.
NCHRP (National Cooperative Highway Research Program). 2012. Design guidance for high-speed to low-speed transition zones for rural highways. NCHRP Rep. 737. Washington, DC: Transportation Research Board.
Okamura, H., S. Watanabe, and T. Watanabe. 2000. “An empirical study on the capacity of bottlenecks on the basic suburban expressway sections in Japan.” In Vol. 12 of Proc., 4th Int. Symp. on Highway Capacity, 110–129. Washington, DC: Transportation Research Board.
Othman, S., and R. Thomson. 2007. Influence of road characteristics on traffic safety. Washington, DC: Transportation Research Board.
Psarianos, B., M. Kontaratos, and D. Katsios. 1995. Influence of vehicle parameters on horizontal curve design of rural highways. Washington, DC: Transportation Research Board.
Qu, G., Y. He, X. Sun, and J. Tian. 2018. “Modeling of lateral stability of tractor-semitrailer on combined alignments of freeway.” Discrete Dyn. Nat. Soc. 2018 (Jan): 1–17. https://doi.org/10.1155/2018/8438921.
Rezapour, M., M. Moomen, and K. Ksaibati. 2019. “Ordered logistic models of influencing factors on crash injury severity of single and multiple-vehicle downgrade crashes: A case study in Wyoming.” J. Saf. Res. 68 (Feb): 107–118. https://doi.org/10.1016/j.jsr.2018.12.006.
Shurtz, M. L. 2006. Effects of ABS controller parameters on heavy truck model braking performance. Columbus, OH: Ohio State Univ.
Smith, P., J. Ward, J. Pierce, D. Bevly, and R. Daily. 2019. “Experimental results and analysis of a longitudinal controlled cooperative adaptive cruise control (CACC) truck platoon.” In Proc., ASME 2019 Dynamic Systems and Control Conf. New York: ASME.
Tavassoli Kallebasti, B., A. Abdi Kordani, S. Mavromatis, and S. M. Boroomandrad. 2018. “Lateral friction demand on roads with coincident horizontal and vertical sag curves.” In Proc., Institution of Civil Engineers Transport, 1–11. London: Thomas Telford.
Varunjikar, T. 2011. Design of horizontal curves with downgrade using low-order vehicle dynamics models. State College, PA: Pennsylvania State Univ.
Willey, W. E. 1955. “Truck congestion on uphill grades.” Highway Res. Board Bull. 104: 21–31.
Wu, J. M., X. F. Yang, and X. Y. Mi. 2011. “Safety treatment technique for continuous downgrade slope.” In Proc., ICTIS 2011: Multimodal Approach to Sustained Tansportation System Development: Information, Technology, Implementation, 182–189. Reston, VA: ASCE. https://doi.org/10.1061/41177(415)23.
Xin, C., Z. Yi, Z. Yong, and M. Yan. 2020. “Optimization on design parameters of road longitudinal slope based on truck dynamics.” In Green, smart and connected transportation, 1325–1343. Singapore: Springer.
Xing, E., Y. Feng, and R. Wang. 2010. “Road safety analysis of long downgrade highway based on the property of vehicle brakes heat-resistant.” In Proc., 2010 Int. Conf. Measuring Technology and Mechatronics Automation (ICMTMA), 258–261. New York: IEEE.
Yoshizawa, R., Y. Shiomi, N. Uno, K. Iida, and M. Yamaguchi. 2012. “Analysis of car- following behavior on sag and curve sections at intercity expressways with driving simulator.” Int. J. Intell. Transp. Syst. Res. 10 (2): 56–65. https://doi.org/10.1007/s13177-011-0043-z.
Yu, R., Y. Xiong, and M. Abdel-Aty. 2015. “A correlated random parameter approach to investigate the effects of weather conditions on crash risk for a mountainous freeway.” Transp. Res. Part C 50 (Jan): 68–77. https://doi.org/10.1016/j.trc.2014.09.016.
Information & Authors
Information
Published In
Copyright
© 2020 American Society of Civil Engineers.
History
Received: Apr 8, 2020
Accepted: Aug 28, 2020
Published online: Nov 9, 2020
Published in print: Jan 1, 2021
Discussion open until: Apr 9, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.