Operational Vertical Bending Stresses in Rail: Real-Life Case Study
Publication: Journal of Transportation Engineering, Part A: Systems
Volume 144, Issue 3
Abstract
Train-mounted vertical track deflection (VTD) measurements offer new opportunities for estimating rail bending stresses over long distances. The estimations are possible because of mathematical correlations among rail deflections, rail stresses, and the loads applied to the rail. Previous numerical studies conducted by the authors resulted in a methodology that suggests the use of finite-element models to develop the correlations. These models facilitate the simulation of a stochastically varying track modulus along the track and provide a strong basis for interpreting the deflection data. In this study, data sets collected from a study site were used to validate this methodology for estimating rail bending stresses under passing train loads. The rail-mounted strain gauges and the wheel impact load detector system at the study site provided information about the rail bending strains under known applied loads. This allowed validation of the maximum bending stresses estimated using train-mounted deflection measurements. The magnitude of rail bending stresses was assessed using measurements from different seasons; stress changes over time were also investigated.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors acknowledge the Canadian Rail Research Laboratory (CaRRL) at the University of Alberta for facilitating and funding the project. The CaRRL is funded by the Natural Sciences and Engineering Research Council of Canada (NSERC), Canadian Pacific Railway, Canadian National Railway, the Association of American Railroads—Transportation Technology Center, Inc., the National Research Council of Canada, Transport Canada, and Alberta Innovates—Technology Futures. The authors thank Tom Edwards from CN and Alireza Roghani, a former Ph.D. student at the U of A, for providing the MRail data. Special thanks are also extended to Timothy Robinson from CN for providing information about the locomotive and rail cars.
References
Al-Nazer, L., and Sivathanu, Y. (2012). “In-motion, non-contact rail temperature measurement sensor.”, Federal Railroad Administration, Washington, DC.
Berggren, E. G., Nissen, A., and Paulsson, B. S. (2014). “Track deflection and stiffness measurements from a track recording car.” Proc. Inst. Mech. Eng. Part F: J. Rail Rapid Transit, 228(6), 570–580.
Cannon, D., Edel, K., Grassie, S., and Sawley, K. (2003). “Rail defects: An overview.” Fatigue Fract. Eng. Mater. Struct., 26(10), 865–886.
Dahlberg, T. (2010). “Railway track stiffness variations-consequences and countermeasures.” Int. J. Civ. Eng., 8(1), 1–11.
Deputat, J., Szelazek, J., and Adamski, M. (1993). “Experiences in ultrasonic measurements of stresses in rails.” Rail quality and maintenance for modern railway operation, J. J. Kalker, D. F. Cannon, and O. Orringer, eds., Springer, Dordrecht, Netherlands, 109–118.
Dhanasekar, M., and Bayissa, W. (2011). “Performance of square and inclined insulated rail joints based on field strain measurements.” Proc. Inst. Mech. Eng. Part F: J. Rail Rapid Transit, 226(2), 140–154.
Esveld, C. (2001). Modern railway track, MRT-Productions, Zaltbommel, Netherlands.
Fallah Nafari, S., Gül, M., Hendry, M. T., and Cheng, J. J. R. (2017). “Estimation of vertical bending stress in rails using train-mounted vertical track deflection measurement systems.” Proc. Inst. Mech. Eng. Part F: J. Rail Rapid Transit, in press.
Fallah Nafari, S., Gül, M., Roghani, A., Hendry, M. T., and Cheng, J. J. R. (2015). “Evaluating the potential of a rolling deflection measurement system to estimate track modulus.” Proc. Inst. Mech. Eng. Part F: J. Rail Rapid Transit, in press.
Farritor, S., and Fateh, M. (2013). “Measurement of vertical track deflection from a moving rail car.”, Federal Railroad Administration, Washington, DC.
Greisen, C. J., et al. (2009). “Estimation of rail bending stress from real-time vertical track deflection measurement.” Proc., 2009 Joint Rail Conf. (JRC2009), ASME, Pueblo, CO, 175–182.
Greisen, C. J. (2010). “Measurement, simulation, and analysis of the mechanical response of railroad track.” M.Sc. thesis, Univ. of Nebraska, Lincoln, NE.
Groom, J. (1983). “Determination of residual stresses in rails.”, Federal Railroad Administration, Washington, DC.
Hay, W. W. (1982). Railroad engineering, Wiley, New York.
Kelleher, J., et al. (2003). “The measurement of residual stress in railway rails by diffraction and other methods.” J. Neutron Res., 11(4), 187–193.
Koc, W., and Wilk, A. (2009). “Investigations of methods to measure longitudinal forces in continuous welded rail tracks using the tamping machine.” Proc. Inst. Mech. Eng. Part F: J. Rail Rapid Transit, 223(1), 61–73.
Li, D., Thompson, R., Marquez, P., and Kalay, S. (2004). “Development and implementation of a continuous vertical track-support testing technique.” Transp. Res. Rec., 1863, 68–73.
Lu, S. (2008). “Real-time vertical track deflection measurement system.” Ph.D. dissertation, Univ. of Nebraska, Lincoln, NE.
Norman, C. D. (2004). “Measurement of track modulus from a moving railcar.” M.Sc. thesis, Univ. of Nebraska, Lincoln, NE.
Orringer, O., Tang, Y. H., Gordon, J. E., Jeong, D. Y., Morris, J. M., and Perlman, A. B. (1988). “Crack propagation life of detail fractures in rails.”, Federal Railroad Administration, Washington, DC.
Roghani, A., and Hendry, M. T. (2016). “Continuous vertical track deflection measurements to map subgrade condition along a railway line: Methodology and case studies.” J. Transp. Eng., 04016059.
Sperry Rail Service. (1964). Rail defect manual, Danbury, CT.
Sussman, T., Ebersöhn, W., and Selig, E. (2001). “Fundamental nonlinear track load-deflection behavior for condition evaluation.” Transp. Res. Rec., 1742, 61–67.
Transport Canada. (2016). Canadian rail operating rules, Ottawa.
TSB (Transportation Safety Board of Canada). (2015). Statistical summary railway occurrences 2014, Gatineau, QC, Canada.
Wegner, A. (2007). “Prevention of track buckling and rail fracture by non-destructive testing of the neutral temperature in cw-rails.” Proc., Int. Heavy Haul Conf., International Heavy Haul Association, Virginia Beach, VA, 557–564.
Zerbst, U., and Beretta, S. (2011). “Failure and damage tolerance aspects of railway components.” Eng. Failure Anal., 18(2), 534–542.
Zerbst, U., Lundén, R., Edel, K., and Smith, R. A. (2009a). “Introduction to the damage tolerance behaviour of railway rails—A review.” Eng. Fract. Mech., 76(17), 2563–2601.
Zerbst, U., Schödel, M., and Heyder, R. (2009b). “Damage tolerance investigations on rails.” Eng. Fract. Mech., 76(17), 2637–2653.
Zhang, Y., Clemenzi, J., Kesler, K., and Lee, S. (2007). “Real time prediction of rail temperature.” Proc., AREMA 2007 Annual Conf., American Railway Engineering and Maintenance-of-Way Association, Lanham, MD.
Information & Authors
Information
Published In
Copyright
©2017 American Society of Civil Engineers.
History
Received: Apr 25, 2017
Accepted: Aug 14, 2017
Published online: Dec 21, 2017
Published in print: Mar 1, 2018
Discussion open until: May 21, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.