Analytical Modeling and Design Resistance of Axially Loaded CHS XX Joints
Publication: Journal of Structural Engineering
Volume 150, Issue 2
Abstract
The design axial resistance for circular hollow section (CHS) XX joints is typically calculated as the product of the CHS X joint resistance and a multiplanar factor. A simple function has been used as the multiplanar factor, which is independent of the joint geometry parameters. In this study, it is first shown that the geometry-independent multiplanar factor does not properly reflect the true behavior of CHS XX joints, resulting in an overly conservative design for joints with large braces. Therefore, an analytical ring model is developed that more accurately captures the effect of the two important nondimensional geometric parameters, namely the brace-to-chord diameter ratio () and chord diameter-to-thickness ratio (). Subsequently, extensive test-validated numerical parametric analyses are performed, including a wide range of geometric and loading parameters, to propose an improved design resistance based on the developed analytical ring model. The formulated design resistance showed a better accuracy compared to the current code design resistance.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
This work was supported by the BK21 FOUR (Fostering Outstanding Universities for Research) Project in 2022 (No. 412200113771).
References
AWS (American Welding Society). 2020. Structural welding code—Steel. AWS D1.1/D.1.M:2020. Doral, FL: AWS.
CEN (European Committee for Standardization). 2021. Eurocode 3: Design of steel structures (Draft), Part 1.8: Design of joints. Brussels, Belgium: CEN.
Chiew, S. P., C. K. Soh, and T. C. Fung. 1997. “Large scale testing of a multiplanar tubular DX-joint.” In Proc., 7th Int. Offshore and Polar Engineering Conf. (ISOPE-97), 112–118. Mountain View, CA: International Society of Offshore and Polar Engineers.
Chong, C. Y., C. K. Soh, A. K. Soh, T. C. Fung, and S. P. Chiew. 1995. “Ultimate capacity of multi-planar double X-Joints.” In Proc., 5th Int. Offshore and Polar Engineering Conf. Mountain View, CA: International Society of Offshore and Polar Engineers.
DSS (Dassault Systèmes Simulia). 2014. Abaqus/CAE user’s guide (ver. 6.14). Providence, RI: DSS.
ISO (International Organization for Standardization). 2013. Static design procedure for welded hollow-section joints—Recommendations. Geneva: ISO.
Kim, S.-H., and C.-H. Lee. 2021. “Analytical strength prediction model for full-width circular hollow section X-joints.” J. Struct. Eng. 147 (9): 04021135. https://doi.org/10.1061/(ASCE)ST.1943-541X.0003087.
Lee, C.-H., S.-H. Kim, D.-H. Chung, D.-K. Kim, and J.-W. Kim. 2017. “Experimental and numerical study of cold-formed high-strength steel CHS X-joints.” J. Struct. Eng. 143 (8): 04017077. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001806.
Lu, L. H., G. D. Winkel, Y. Yu, and J. Wardenier. 1994. “Deformation limit for the ultimate strength of hollow section joints.” In Proc., 6th Int. Symp. on Tubular Structures (Tubular Structure VI), 341–347. Rotterdam, Netherlands: A.A. Balkema.
Paul, J. C., C. A. C. Valk, and J. Wardenier. 1989. “The static strength of circular multiplanar X-joints.” In Proc., 3rd IIW Int. Symp. on Tubular Structures. London: International Institute of Welding.
Suk, C.-H., C.-H. Lee, and S.-H. Kim. 2022. “Analytical modeling and strength prediction of CHS XX-joints subjected brace axial compression.” [in Korean.] J. Korean Soc. Steel Constr. 34 (3): 129–140.
Togo, T. 1967. “Experimental study on mechanical behavior of tubular joints.” Ph.D. dissertation, Dept. of Architectural Engineering, Osaka Univ.
Vegte, G. J. 1995. “The static strength of uniplanar and multiplanar tubular T- and X-joints.” Ph.D. dissertation, Dept. of Civil Engineering and Geosciences, Delft Univ. of Technology.
Vegte, G. J., J. Wardenier, X. L. Zhao, and J. A. Packer. 2008. “Evaluation of new CHS strength formulae to design strengths.” In Proc., 12th Int. Symp. on Tubular Structures (Tubular Structures XII), 313–322. Boca Raton, FL: CRC Press.
Wardenier, J., Y. Kurobane, J. A. Packer, G. J. Van der Vegte, and X.-L. Zhao. 2008. Construction with hollow steel sections—No.1: Design guide for circular hollow section (CHS) joints under predominantly static loading. 2nd ed. Geneva: CIDECT.
Yun, X., and L. Gardner. 2017. “Stress-strain curves for hot-rolled steels.” J. Constr. Steel Res. 133 (Jun): 36–46. https://doi.org/10.1016/j.jcsr.2017.01.024.
Information & Authors
Information
Published In
Copyright
© 2023 American Society of Civil Engineers.
History
Received: Jun 21, 2023
Accepted: Sep 29, 2023
Published online: Dec 5, 2023
Published in print: Feb 1, 2024
Discussion open until: May 5, 2024
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.