Shear Strength and Crack Width Control of Concrete Beams with High-Strength Shear Reinforcement
Publication: Journal of Structural Engineering
Volume 150, Issue 3
Abstract
There is a potential to reduce steel tonnage for construction through the use of high-strength steel reinforcement. However, the current version of the ACI 318 code limits the yield strength of reinforcement that could be used for shear design under gravity load conditions to 420 MPa to control diagonal crack widths. This limit is increased to 550 MPa for resisting seismic shear in special moment frames. In the current study, 12 full-scale RC beam specimens were tested to investigate the shear behavior of RC beams with high-strength SD790 () shear reinforcement. The test variables considered in the experimental study were shear-span-to-depth ratio, stirrup spacing, stirrup yield strength, concrete compressive strength, and longitudinal reinforcement ratio. The test results of this research and those collected from the literature showed that the stress limit of the ACI 318 shear strength equations could be increased to 600 MPa for shear strength calculation. The stress limit of 790 MPa produced conservative predictions for most of the test data and for all the data if the strength reduction factor for shear design was considered. However, the degree of conservatism was significantly reduced. Also, an equation to estimate the maximum shear crack width was proposed. The proposed crack-width equation was able to predict the crack widths observed in the current and other reference studies with reasonable accuracy.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or codes generated or used during the study are available from the corresponding author by request. (Lateral force and displacement relationships.)
Acknowledgments
The authors would like to thank the support from the National Science and Technology Council of Taiwan under Contract No. 111-2625-M-002-009 and the National Center for Research on Earthquake Engineering (NCREE) of Taiwan. The authors also sincerely thank Chieh-Yu Huang for her assistance in conducting the experiments.
References
AASHTO. 2004. AASHTO LRFD bridge design specifications and commentary. 3rd ed. Washington, DC: AASHTO.
ACI (American Concrete Institute). 2005. Building code requirements for structural concrete (ACI 318-05) and commentary. ACI 318-05. Farmington Hills, MI: ACI.
ACI (American Concrete Institute). 2019. Building code requirements for structural concrete (ACI 318-19) and commentary. ACI 318-19. Farmington Hills, MI: ACI.
Ahmad, S. H., A. R. Khaloo, and A. Poveda. 1986. “Shear capacity of reinforced high-strength concrete beams.” ACI J. Proc. 83 (2): 297–305. https://doi.org/10.14359/10433.
ASTM. 2011. Standard specification for deformed and plain, low-carbon, chromium, steel bars for concrete reinforcement. ASTM A1035/A1035M-11. West Conshohocken, PA: ASTM.
CEN (European Committee for Standardization). 2004. Design of concrete structures—Part 101: General rules and rules for buildings. Eurocode 2. Brussels, Belgium: CEN.
Chiu, C.-K., K.-N. Chi, and F.-C. Lin. 2014. “Experimental investigation on the shear crack development of shear-critical high-strength reinforced concrete beams.” J. Adv. Concr. Technol. 12 (7): 223–238. https://doi.org/10.3151/jact.12.223.
Chiu, C.-K., T. Ueda, K.-N. Chi, and S.-Q. Chen. 2016. “Shear crack control for high strength reinforced concrete beams considering the effect of shear-span to depth ratio of member.” Int. J. Concr. Struct. Mater. 10 (4): 407–424. https://doi.org/10.1007/s40069-016-0161-8.
Cladera, A., and A. R. Mari. 2005. “Experimental study on high-strength concrete beams failing in shear.” Eng. Struct. 27 (10): 1519–1527. https://doi.org/10.1016/j.engstruct.2005.04.010.
CSA (Canadian Standard Association). 2004. Design of concrete structures. CSA A23.3-04. Toronto: CSA.
CSA (Canadian Standard Association). 2019. Design of concrete structures. CSA A23.3-19. Toronto: CSA.
Desalegne, A. S., and A. S. Lubell. 2015. “Shear in concrete beams reinforced with high-performance steel.” ACI Struct. J. 112 (6): 783–792. https://doi.org/10.14359/51687798.
Elstner, R. C., K. G. Moody, I. M. Viest, and E. Hognestad. 1955. “Shear strength of reinforced concrete beams Part 3—Tests of restrained beams with web reinforcement.” ACI J. Proc. 51 (2): 525–539. https://doi.org/10.14359/11693.
Elzanaty, A. H., A. H. Nilson, and F. O. Slate. 1986. “Shear capacity of reinforced concrete beams using high-strength concrete.” ACI J. Proc. 83 (2): 290–296. https://doi.org/10.14359/10432.
Frosch, R. J. 2000. “Behavior of large-scale reinforced concrete beams with minimum shear reinforcement.” ACI Struct. J. 97 (6): 814–820. https://doi.org/10.14359/9626.
Guralnick, S. A. 1960. “High-strength deformed steel bars for concrete reinforcement.” ACI J. Proc. 57 (9): 241–282. https://doi.org/10.14359/8020.
Haddadin, M. J., S.-T. Hong, and A. H. Mattock. 1971. “Stirrup effectiveness in reinforced concrete beams with axial force.” J. Struct. Div. 97 (9): 2277–2297. https://doi.org/10.1061/JSDEAG.0002996.
Johnson, M. K., and J. A. Ramirez. 1989. “Minimum shear reinforcement in beams with higher strength concrete.” ACI Struct. J. 86 (4): 376–382. https://doi.org/10.14359/2896.
JSCE (Japan Society of Civil Engineers). 2007. Standard specifications for concrete structures. Tokyo: JSCE.
Kim, S. 2004. “Prediction of shear behavior of reinforced concrete members using compatibility aided truss models.” Ph.D. thesis, Dept. of Architectural Engineering, Sungkyunkwa Univ.
Kong, P. Y. L., and B. V. Rangan. 1998. “Shear strength of high-performance concrete beams.” ACI Struct. J. 95 (6): 677–688. https://doi.org/10.14359/581.
Kuchma, D. A., S. Wei, D. H. Sanders, A. Belarbi, and L. C. Novak. 2019. “Development of the one-way shear design provisions of ACI 318-19 for reinforced concrete.” ACI Struct. J. 116 (4): 285–296. https://doi.org/10.14359/51716739.
Lee, J.-Y., I.-J. Choi, and S.-W. Kim. 2011. “Shear behavior of reinforced concrete beams with high-strength stirrups.” ACI Struct. J. 108 (5): 620–629. https://doi.org/10.14359/51683219.
Lee, J.-Y., S.-H. Choi, and D. H. Lee. 2016. “Structural behaviour of reinforced concrete beams with high yield strength stirrups.” Mag. Concr. Res. 68 (23): 1187–1199. https://doi.org/10.1680/jmacr.15.00344.
Lee, J.-Y., M. Haroon, D. Shin, and S.-W. Kim. 2021. “Shear and torsional design of reinforced concrete members with high-strength reinforcement.” J. Struct. Eng. 147 (2): 04020327. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002887.
Lee, J.-Y., and H.-B. Hwang. 2010. “Maximum shear reinforcement of reinforced concrete beams.” ACI Struct. J. 107 (5): 580. https://doi.org/10.14359/51663909.
Lee, J.-Y., and U.-Y. Kim. 2008. “Effect of longitudinal tensile reinforcement ratio and shear span-depth ratio on minimum shear reinforcement in beams.” ACI Struct. J. 105 (2): 134. https://doi.org/10.14359/19728.
Lee, J.-Y., D. H. Lee, J.-E. Lee, and S.-H. Choi. 2015. “Shear behavior and diagonal crack width for reinforced concrete beams with high-strength shear reinforcement.” ACI Struct. J. 112 (3): 323–333. https://doi.org/10.14359/51687422.
Lee, J.-Y., J.-H. Lee, D. H. Lee, S.-J. Hong, and H.-Y. Kim. 2018. “Practicability of large-scale reinforced concrete beams using grade 80 stirrups.” ACI Struct. J. 115 (1): 269–280. https://doi.org/10.14359/51701147.
Lin, F.-Q. 2014. “Study on the shear cracking control for high strength reinforced concrete beams.” Master’s thesis, Dept. of Civil and Construction Engineering, College of Engineering, National Taiwan Univ. of Science and Technology.
Mattock, A. H., and Z. Wang. 1984. “Shear strength of reinforced concrete members subject to high axial compressive stress.” ACI J. Proc. 81 (3): 287–298. https://doi.org/10.14359/10685.
Mphonde, A. G., and G. C. Frantz. 1985. “Shear tests of high- and low-strength concrete beams with stirrups.” ACI Symp. Publ. 87 (Sep): 179–196. https://doi.org/10.14359/6529.
Munikrishna, A., A. Hosny, S. Rizkalla, and P. Zia. 2011. “Behavior of concrete beams reinforced with ASTM A1035 grade 100 stirrups under shear.” ACI Struct. J. 108 (1): 34–41. https://doi.org/10.14359/51664200.
NCREE (National Center for Research on Earthquake Engineering). 2019. Design guideline for building of high-strength reinforced concrete structures. NCREE 19-001. Taipei, Taiwan: NCREE.
Nie, J., and C. S. Cai. 2000. “Deflection of cracked RC beams under sustained loading.” J. Struct. Eng. 126 (6): 708–716. https://doi.org/10.1061/(ASCE)0733-9445(2000)126:6(708).
NZS (New Zealand Standards). 2006. The design of concrete structures 3101-2006. Wellington, New Zealand: NZS.
Ou, Y.-C., and N. V. B. Nguyen. 2022. “Stress limit for shear reinforcement of high-strength columns.” ACI Struct. J. 119 (1): 131–141. https://doi.org/10.14359/51733002.
Ozcebe, G., U. Ersoy, and T. Tankut. 1999. “Evaluation of minimum shear reinforcement requirements for higher strength concrete.” ACI Struct. J. 96 (3): 361–368. https://doi.org/10.14359/669.
Pendyala, R. S., and P. Mendis. 2000. “Experimental study on shear strength of high-strength concrete beams.” ACI Struct. J. 97 (4): 564–571. https://doi.org/10.14359/7421.
Placas, A., and P. E. Regan. 1971. “Shear failure of reinforced concrete beams.” ACI J. Proc. 68 (10): 763–773. https://doi.org/10.14359/15237.
Rahal, K. N., and K. S. Al-Shaleh. 2004. “Minimum transverse reinforcement in 65 MPa concrete beams.” ACI Struct. J. 101 (6): 872–878. https://doi.org/10.14359/13463.
Roller, J. J., and H. G. Russel. 1990. “Shear strength of high-strength concrete beams with web reinforcement.” ACI Struct. J. 87 (2): 191–198. https://doi.org/10.14359/2682.
Sarsam, K. F., and J. M. Al-Musawi. 1992. “Shear design of high-and normal strength concrete beams with web reinforcement.” ACI Struct. J. 89 (6): 658–664. https://doi.org/10.14359/9644.
Shin, D., M. Haroon, C. Kim, B.-S. Lee, and J.-Y. Lee. 2019. “Shear strength reduction of large-scale reinforced concrete beams with high-strength stirrups.” ACI Struct. J. 116 (5): 161–171. https://doi.org/10.14359/51716759.
Sumpter, M. S., S. H. Rizkalla, and P. Zia. 2009. “Behavior of high-performance steel as shear reinforcement for concrete beams.” ACI Struct. J. 107 (1): 122–124. https://doi.org/10.14359/56355.
Tan, S. 2010. “Maximum amount of shear reinforcement of reinforced concrete beams.” Master’s thesis, Dept. of Civil Engineering, College of Engineering, National Taiwan Univ.
Tompos, E. J., and R. J. Frosch. 2002. “Influence of beam size, longitudinal reinforcement, and stirrup effectiveness on concrete shear strength.” ACI Struct. J. 99 (5): 559–567. https://doi.org/10.14359/12295.
Xie, Y., S. H. Ahmad, T. Yu, S. Hino, and W. Chung. 1994. “Shear ductility of reinforced concrete beams of normal and high-strength concrete.” ACI Struct. J. 91 (2): 140–149. https://doi.org/10.14359/4592.
Yoon, Y. S., W. D. Cook, and D. Mitchell. 1996. “Minimum shear reinforcement in normal, medium, and high-strength concrete beams.” ACI Struct. J. 93 (5): 576–584. https://doi.org/10.14359/9716.
Information & Authors
Information
Published In
Copyright
© 2024 American Society of Civil Engineers.
History
Received: Jan 15, 2023
Accepted: Nov 7, 2023
Published online: Jan 16, 2024
Published in print: Mar 1, 2024
Discussion open until: Jun 16, 2024
ASCE Technical Topics:
- Beams
- Concrete
- Concrete beams
- Continuum mechanics
- Cracking
- Engineering fundamentals
- Engineering materials (by type)
- Engineering mechanics
- Fracture mechanics
- High-strength concrete
- High-strength steel
- Laboratory tests
- Material mechanics
- Material properties
- Materials engineering
- Metals (material)
- Reinforced concrete
- Shear strength
- Shear tests
- Solid mechanics
- Steel
- Strength of materials
- Structural engineering
- Structural members
- Structural systems
- Tests (by type)
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.