Experimental Investigation on Flexural Behavior of U-Shaped Steel–Concrete Composite Beams with Bolt Connections under a Negative Bending Moment
Publication: Journal of Structural Engineering
Volume 149, Issue 7
Abstract
Because U-shaped steel beams filled with concrete have the advantages of reduced construction period and superior structural performance, they have been widely used as structural elements. In this study, the flexural behavior of newly developed bolt-connected U-shaped steel and concrete composite beams under a negative bending moment was experimentally evaluated. The main test variables were bolt spacing in bottom steel plates and types of U-shaped steel sections. Test results showed that the flexural behavior of the composite beams is determined by the plate-buckling mode of bolt-connected bottom steel plates. Composite beams with a greater bolt spacing than that in the standard AISI S100-16 experienced early plate buckling of the bottom steel plates, resulting in reduction of flexural stiffness and maximum flexural strength. Thus, the buckling mode of bolt-connected bottom plates should be considered for bolt-connected U-shaped composite beams under a negative bending moment. The longitudinal lips of U-shaped steel sections can increase the flexural performance of composite beams due to anchorage performance of the steel sections with lips.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
This study was supported by CGS Plan Co., National Research Foundation of Korea (NRF) funded by the Korean Government Ministry of Education (NRF-2018R1A6A1A07025819), and Ewha Womans University Research Grant of 2022.
References
Abdel Sayed, G. 1982. “Composite cold-formed steel-concrete structural system.” In Proc., Int. Specialty Conf. on Cold-Formed Steel Structures, 485. Rolla, MO: Missouri Univ. of Science and Technology.
AIK (Architectural Institute of Korea). 2019. Design code for structural steel buildings. KDS 41 31 00. Seoul: AIK.
AISC. 2010. Specification for structural steel buildings. ANSI/AISC 360-10. Chicago: AISC.
AISC. 2016. Specification for structural steel buildings. ANSI/AISC 360-16. Chicago: AISC.
AISI (American Iron and Steel Institute). 2016. North American specification for the design of cold-formed steel structural members. AISI S100-16. Washington, DC: AISI.
ASCE. 2017. Seismic rehabilitation of existing buildings. ASCE 41-17: Reston, VA: ASCE.
Bamaga, S., M. M. Tahir, T. Tan, S. Mohammad, N. Yahya, A. Saleh, M. Mustaffar, M. Osman, and A. Rahman. 2013. “Feasibility of developing composite action between concrete and cold-formed steel beam.” J. Cent. South Univ. 20 (12): 3689–3696. https://doi.org/10.1007/s11771-013-1897-9.
Cao, L., Y. Li, M. Dhanasekar, and C. Lu. 2021. “Experimental and numerical study on flexural performance of a novel steel-encased concrete composite beam.” KSCE J. Civ. Eng. 25 (5): 1837–1848. https://doi.org/10.1007/s12205-021-1196-1.
CEN (European Committee for Standardization). 2004. Eurocode 4: Design of composite steel and concrete structures. Part 1.1. Brussels, Belgium: CEN.
Chajes, A. 1974. Principles of structural stability theory. Hoboken, NJ: Prentice Hall.
Chen, L., S. Li, H. Zhang, and X. Wu. 2018. “Experimental study on mechanical performance of checkered steel-encased concrete composite beam.” J. Constr. Steel Res. 143 (Apr): 223–232. https://doi.org/10.1016/j.jcsr.2017.12.021.
Khandaker, M., and A. Hossain. 2003. “Experimental & theoretical behavior of thin walled composite filled beams.” Electron. J. Struct. Eng. 3 (Jan): 117–139. https://doi.org/10.56748/ejse.334.
Kim, S. B., E. T. Lee, J. R. Kim, and S. S. Kim. 2016. “Experimental study on bending behavior and seismic performance of hybrid composite beam with new shape.” Int. J. Steel Struct. 16 (2): 477–488. https://doi.org/10.1007/s13296-016-6018-9.
Lai, Z., and A. H. Varma. 2015. “Noncompact and slender circular CFT members: Experimental database, analysis, and design.” J. Constr. Steel Res. 106 (Mar): 220–233. https://doi.org/10.1016/j.jcsr.2014.11.005.
Lai, Z., A. H. Varma, and K. Zhang. 2014. “Noncompact and slender rectangular CFT members: Experimental database, analysis, and design.” J. Constr. Steel Res. 101 (Oct): 455–468. https://doi.org/10.1016/j.jcsr.2014.06.004.
Lawson, R. M., and H. Taufiq. 2019. “Partial shear connection in light steel composite beams.” J. Constr. Steel Res. 154 (Mar): 55–66. https://doi.org/10.1016/j.jcsr.2018.11.005.
Leon, R. T., D. K. Kim, and J. F. Hajjar. 2007. “Limit state response of composite columns and beam-columns Part 1: Formulation of design provisions for the 2005 AISC specification.” Eng. J.-Am. Inst. Steel Constr. 44 (4): 341.
Liu, J., Y. Zhao, Y. F. Chen, S. Xu, and Y. Yang. 2018. “Flexural behavior of rebar truss stiffened cold-formed U-shaped steel-concrete composite beams.” J. Constr. Steel Res. 150 (Nov): 175–185. https://doi.org/10.1016/j.jcsr.2018.08.011.
Liu, J., Y. Zhao, Y. Yang, and Y. F. Chen. 2019. “Bending capacity and elastic stiffness for a novel configuration of cold-formed U-shaped steel-and-concrete composite beams.” J. Struct. Eng. 145 (10): 04019106. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002394.
Liu, Y., L. Guo, B. Qu, and S. Zhang. 2017. “Experimental investigation on the flexural behavior of steel-concrete composite beams with U-shaped steel girders and angle connectors.” Eng. Struct. 131 (Jan): 492–502. https://doi.org/10.1016/j.engstruct.2016.10.037.
Nakamura, S. I. 2002. “Bending behavior of composite girders with cold formed steel U section.” J. Struct. Eng. 128 (9): 1169–1176. https://doi.org/10.1061/(ASCE)0733-9445(2002)128:9(1169).
Nguyen, R. P. 1991. “Thin-walled, cold-formed steel composite beams.” J. Struct. Eng. 117 (10): 2936–2952. https://doi.org/10.1061/(ASCE)0733-9445(1991)117:10(2936).
Turetta, M., C. Odenbreit, A. Khelil, and P. Martin. 2020. “Investigation on the flexural behavior of an innovative U-shaped steel-concrete composite beam.” Steel Compos. Struct. Int. J. 34 (3): 441–452. https://doi.org/10.12989/scs.2020.34.3.441.
Winter, G. 1970. Commentary on the 1968 edition of the specification for the design of cold-formed steel structural members. New York: American Iron and Steel Institute.
Xu, C., Q. Su, C. Wu, and K. Sugiura. 2011. “Experimental study on double composite action in the negative flexural region of two-span continuous composite box girder.” J. Constr. Steel Res. 67 (10): 1636–1648. https://doi.org/10.1016/j.jcsr.2011.04.007.
Yu, W. W., R. A. LaBoube, and H. Chen. 2019. Cold-formed steel design. New York: Wiley.
Zhao, Y., X. Zhou, Y. Yang, Y. F. Chen, and S. Gurupackiam. 2020. “Stiffness and cracking behavior of new U-shaped steel and concrete composite beam under negative bending.” J. Struct. Eng. 146 (5): 04020046. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002594.
Zhao, Y., X. Zhou, Y. Yang, J. Liu, and Y. F. Chen. 2019. “Shear behavior of a novel cold-formed U-shaped steel and concrete composite beam.” Eng. Struct. 200 (Dec): 109745. https://doi.org/10.1016/j.engstruct.2019.109745.
Zhou, X., Y. Zhao, J. Liu, Y. F. Chen, and Y. Yang. 2019. “Bending experiment on a novel configuration of cold-formed U-shaped steel-concrete composite beams.” Eng. Struct. 180 (Feb): 124–133. https://doi.org/10.1016/j.engstruct.2018.11.001.
Ziemian, R. D. 2010. Guide to stability design criteria for metal structures. New York: Wiley.
Information & Authors
Information
Published In
Copyright
© 2023 American Society of Civil Engineers.
History
Received: Sep 23, 2022
Accepted: Mar 3, 2023
Published online: May 10, 2023
Published in print: Jul 1, 2023
Discussion open until: Oct 10, 2023
ASCE Technical Topics:
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.