Analytical Model Development for CLT Diaphragms Loaded Perpendicular to the Length of Panels
Publication: Journal of Structural Engineering
Volume 149, Issue 6
Abstract
The main objective of this study was to develop an analytical model for predicting the diaphragm deflection and the induced shear force at the panel joints when the applied load is perpendicular to the panel length. An equivalent finite-element model was developed to capture the elastic behavior of the diaphragm made from the panels and the connections in between. The analytical model’s predictions were compared with predictions from finite-element models. The results of an experimental test were used to partially validate the analytical and numerical models in the absence of full-scale diaphragm test data. A sensitivity analysis was carried out with the aim of finding the most influential parameters in the behavior of the cross-laminated timber (CLT) diaphragm. The connection’s stiffness and diaphragm size were varied. The difference in diaphragm deflection was investigated, and it was found that under realistic material properties and geometry, the diaphragm deflection was not strongly related to the connection’s stiffness. However, the floor’s geometry was the key influencing parameter. A parametric study was performed, and the contribution of each deflection component was quantified for each specific case. It was observed that the floor’s flexibility was dominated mainly by the shear deflection of the cross-laminated timber panels as well as the slip in the panel joints as the length of the diaphragm increased. This study proposes a method that designers may use to estimate the in-plane displacement of the cross-laminated timber diaphragm when it is loaded perpendicular to the panel’s length.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all of the data, models, or codes that supported the findings of this study are available from the corresponding author upon request.
Acknowledgments
The authors would like to thank the Natural Sciences and Engineering Research Council of Canada (NSERC) for the financial support of this study under the Industrial Research Chair Program. Financial support was also provided by Landmark Group of Companies, FPInnovations, Canadian Wood Council, MTC Solutions, Rotho Blaas, Western Archrib, and Alberta Innovates. Their support is gratefully acknowledged.
References
ABAQUS. 2011. Abaqus 6.11 theory manual. Providence, RI: Dassault Systemes Simulia Corporation.
ANSI (American National Standard Institution). 2012. Standards for performance-rated cross-laminated timber. ANSI/APA PRG 320–2012. Tacoma, AZ: ANSI/APA.
Ashtari, S. 2012. “In-plane stiffness of cross-laminated timber floors.” Master’s of Applied Science thesis, Dept. of Civil Engineering, Univ. of British Columbia.
Barbosa, A. R., L. G. Rodrigues, A. Sinha, C. Higgins, R. B. Zimmerman, S. Breneman, S. Pei, J. W. van de Lindt, J. Berman, and E. McDonnell. 2021. “Shake-table experimental testing and performance of topped and untopped cross-laminated timber diaphragms.” J. Struct. Eng. 147 (4): 4021011. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002914.
Beairsto, C., R. Gupta, and M. Thomas. 2020. “Monotonic and cyclic behavior of CLT diaphragms.” Pract. Period. Struct. Des. Constr. 27 (2). https://doi.org/10.1061/(ASCE)SC.1943-5576.0000658.
Blass, H. J., and P. Fellmoser. 2004. “Design of solid wood panels with cross layers.” In Proc., 8th World Conf. on Timber Engineering WCTE 2004, 543–548. Helsinki, Finland: Finnish Association of Civil Engineers.
Bogensperger, T., T. Moosbrugger, and G. Silly. 2010. “Verification of CLT-plates under loads in plane.” In Proc., 11th World Conf. on Timber Engineering (WCTE2010), 885–898. Florence, Italy: Trees and Timber Institute, National Research Council.
Brandner, R., T. Bogensperger, and G. Schickhofer. 2013. “In plane shear strength of cross laminated timber (CLT): Test configuration, quantification and influencing parameters.” In Proc., 46th CIB-W18 Meeting. Ottawa: International Council for Research and Innovation in Building and Construction.
Brandner, R., P. Dietsch, J. Dröscher, M. Schulte-Wrede, H. Kreuzinger, and M. Sieder. 2017. “Cross laminated timber (CLT) diaphragms under shear: Test configuration, properties and design.” Constr. Build. Mater. 147 (Aug): 312–327. https://doi.org/10.1016/j.conbuildmat.2017.04.153.
Breneman, S., E. McDonnell, and R. B. Zimmerman. 2016. “An approach to CLT diaphragm modeling for seismic design with application to a U.S. high-rise project.” In Proc., World Conf. on Timber Engineering, WCTE. Vienna, Austria: Vienna Univ. of Technology.
Ceccotti, A., C. Sandhaas, M. Okabe, M. Yasumura, C. Minowa, and N. Kawai. 2013. “SOFIE project–3D shaking table test on a seven-storey full-scale cross-laminated timber building.” Earthquake Eng. Struct. Dyn. 42 (13): 2003–2021. https://doi.org/10.1002/eqe.2309.
CEN (European Committee for Standardization). 2004. Eurocode 5: Design of timber structures–Part 1–1: General–common rules and rules for buildings. EN 1995-1-1. Brussels, Belgium: CEN.
Chui, Y. H., and D. W. Barclay. 1998. “Analysis of three-layer beams with non-identical layers and semi-rigid connections.” Can. J. Civ. Eng. 25 (2): 271–276. https://doi.org/10.1139/l97-093.
Chui, Y. H., J. Spencer, T. Joyce, H. Daneshvar, J. Niederwestberg, and M. Spasojevic. 2019. “Structural timber design in curricula of Canadian universities: Current status and future needs.” Educ. Sci. 11 (12): 765. https://doi.org/10.3390/educsci11120765.
Computers and Structures Inc. 2005. CSI analysis reference manual for SAP2000. Berkeley, CA: Computers and Structures.
Daneshvar, H., J. Niederwestberg, C. Dickof, and Y. H. Chui. 2021. “Structural behaviour of deep CLT lintels subjected to concentric and eccentric loading.” J. Build. Eng. 43 (Nov): 103101. https://doi.org/10.1016/j.jobe.2021.103101.
D’Arenzo, G., D. Casagrande, T. Reynolds, and M. Fossetti. 2019. “In-plane elastic flexibility of cross laminated timber floor diaphragms.” Constr. Build. Mater. 209 (Sep): 709–724. https://doi.org/10.1016/j.conbuildmat.2019.03.060.
Dujic, B., S. Aicher, and R. Zarnic. 2006. “Racking behaviour of light prefabricated cross-laminated massive timber wall diaphragms subjected to horizontal actions.” Otto Graf J. 17 (Aug): 125–142. https://doi.org/10.1016/j.engstruct.2018.06.021.
Dujic, B., J. Pucelj, and R. Zarnic. 2004. “Testing of racking behavior of massive wooden wall panels.” In Proc., 37th CIB-W18 Meeting. Ottawa: International Council for Building Research and Innovation.
Flaig, M., and H. J. Blaß. 2013. “Shear strength and shear stiffness of CLT-beams loaded in plane.” In Proc., Int. Council for Research and Innovation in Building and Construction-Working Commission W18—Timber Structures. Delft, Netherlands: International Council for Research and Innovation in Building and Construction.
Gagnon, S., M. Mohammad, W. M. Toro, and M. Popovski. 2014. “Evaluation of in-plane shear strength of CLT.” In Proc., World Conf. on Timber Engineering, 1–7. Pointe-Claire, QC, Canada: FPInnovations.
Gavric, I., M. Fragiacomo, and A. Ceccotti. 2015. “Cyclic behaviour of typical metal connectors for cross-laminated (CLT) structures.” Mater. Struct. 48 (6): 1841–1857. https://doi.org/10.1617/s11527-014-0278-7.
Goodman, J. R., and E. P. Popov. 1968. “Layered beam systems with interlayer slip.” J. Struct. Div. 94 (11): 2535–2548. https://doi.org/10.1061/JSDEAG.0002116.
Gsell, D., G. Feltrin, S. Schubert, R. Steiger, and M. Motavalli. 2007. “Cross-laminated timber plates: Evaluation and verification of homogenized elastic properties.” J. Struct. Eng. 133 (1): 132–138. https://doi.org/10.1061/(ASCE)0733-9445(2007)133:1(132).
Hossain, A., M. Popovski, and T. Tannert. 2019. “Group effects for shear connections with self-tapping screws in CLT.” J. Struct. Eng. 145 (8): 4019068. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002357.
Joyce, T. P. R. D. 2014. “Connections for CLT diaphragms in steel-frame buildings.” Master’s thesis, Dept. of Forestry Engineering, Univ. of New Brunswick.
Karacebeyli, C., and S. Gagnon. 2019. “Canadian CLT handbook.” Accessed March 3, 2020. https://web.fpinnovations.ca/wp-content/uploads/clt-handbook-complete-version-en-low.pdf.
Kode, A. 2018. “Testing of a full-scale mass timber diaphragm.” Master’s thesis, Dept. of Civil and Environmental Engineering, Colorado State Univ.
Kode, A., M. O. Amini, J. W. van de Lindt, and P. Line. 2021. “Lateral load testing of a full-scale cross-laminated timber diaphragm.” Pract. Period. Struct. Des. Constr. 26 (2): 4021001. https://doi.org/10.1061/(ASCE)SC.1943-5576.0000566.
Lenon, C. 2015. “Design and behavior of a mid-rise cross-laminated timber building.” Accessed January 14, 2016. https://repository.mines.edu/bitstream/handle/11124/169999/Lenon_mines_0052N_10900.pdf?sequence=1&isAllowed=y.
Loss, C., M. Piazza, and R. Zandonini. 2016. “Connections for steel–timber hybrid prefabricated buildings. Part I: Experimental tests.” Supplement, Constr. Build. Mater. 122 (S1): 781–795. https://doi.org/10.1016/j.conbuildmat.2015.12.002.
Moosbrugger, T., W. Guggenberger, and T. Bogensperger. 2006. “Cross-laminated timber wall segments under homogeneous shear–With and without openings.” In Proc., 9th World Conference on Timber Engineering 2006, WCTE 2006, 219–228. Corvallis, OR: Oregon State Univ. Conference Services.
Moroder, D. 2016. “Floor diaphragms in multi-storey timber buildings.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of Canterbury.
NBCC (National Research Council of Canada). 2015. National building code of Canada 2015. Ottawa: Institute for Research in Construction.
NDS (National Design Specification). 2014. National design specification (NDS) for wood construction–with commentary. 2015 ed. Leesburg, VA: American Wood Council.
Popovski, M., and E. Karacabeyli. 2012. “Seismic behaviour of cross-laminated timber structures.” In Proc., World Conf. on Timber Engineering. Auckland, New Zealand: New Zealand Timber Design Society.
Shahnewaz, M., S. Alam, and T. Tannert. 2018. “In-plane strength and stiffness of cross-laminated timber shear walls.” Buildings 8 (8): 100. https://doi.org/10.3390/buildings8080100.
Spickler, K., M. Closen, P. Line, and M. Pohll. 2015. “Cross laminated timber: Horizontal diaphragm design example.” Accessed June 4, 2016. https://www.structurlam.com/wp-content/uploads/2016/10/Structurlam-CrossLam-CLT-White-Paper-on-Diaphragms-SLP-Oct-2015.pdf.
Sullivan, K., T. H. Miller, and R. Gupta. 2018. “Behavior of cross-laminated timber diaphragm connections with self-tapping screws.” Eng. Struct. 168 (Aug): 505–524. https://doi.org/10.1016/j.engstruct.2018.04.094.
Timoshenko, S. 1983. History of strength of materials: With a brief account of the history of theory of elasticity and theory of structures. New York: Dover.
Tupenaite, L., V. Zilenaite, L. Kanapeckiene, T. Gecys, and I. Geipele. 2021. “Sustainability assessment of modern high-rise timber buildings.” Sustainability 13 (16): 8719–8722. https://doi.org/10.3390/su13168719.
Wallner-Novak, M., M. Augustin, J. Koppelhuber, and K. Pock. 2018. “Cross-laminated timber structural design Volume 2: Applications.” Accessed January, 3, 2018. https://www.kurtpock.at/files/content/Veroeffentlichungen/Buecher/2018%20Wallner-Novak%20M.,%20CLT%20structural%20design%20II%20proHOLZ.pdf.
Yawalata, D., and F. Lam. 2011. Development of technology for cross laminated timber building systems. Vancouver, BC, Canada: Univ. of British Columbia.
Information & Authors
Information
Published In
Copyright
© 2023 American Society of Civil Engineers.
History
Received: Jun 8, 2022
Accepted: Dec 16, 2022
Published online: Mar 29, 2023
Published in print: Jun 1, 2023
Discussion open until: Aug 29, 2023
ASCE Technical Topics:
- Analysis (by type)
- Building materials
- Continuum mechanics
- Design (by type)
- Diaphragms (structural)
- Displacement (mechanics)
- Engineering fundamentals
- Engineering materials (by type)
- Engineering mechanics
- Finite element method
- Laminating
- Load factors
- Materials engineering
- Materials processing
- Methodology (by type)
- Numerical methods
- Panels (structural)
- Sensitivity analysis
- Solid mechanics
- Structural design
- Structural engineering
- Structural mechanics
- Structural members
- Structural systems
- Wood and wood products
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.