Evaluation of Total Stress in W-Flange Members Using Ultrasonic Shear Waves
Publication: Journal of Performance of Constructed Facilities
Volume 38, Issue 1
Abstract
This paper discusses the development of ultrasonic stress measurement (USM) technology as a potential tool for structural heath monitoring and evaluation of buildings and bridges. The proposed approach utilizes acoustic birefringence to assess the total stress in steel members. Acoustic birefringence describes the difference in velocity between orthogonally polarized shear waves as a result of anisotropy in the material. This anisotropy comes from texture produced during the manufacturing process and stresses (i.e., strains) in the plate under loading. The relationship between the birefringence and stresses may be a viable method to evaluate the total stress in a steel member, which includes stresses produced from all applied loads, including both dead loads and live loads. This paper investigates steel wide-flange (W-flange) rolled sections under tension and bending. The results indicate that birefringence shows a strong linear correlation with strain. The variation in the in situ birefringence was found to be significant and varied between different locations on the same cross section. If the acoustic constants ( and ) that relate the birefringence to the strain are known, laboratory tests showed that stress can be approximated to within () (2% of the material yield strength, ). If average values of constants across all laboratory testing were used, the error increased to () (28% ). These results indicate that ultrasonic stress measurement based on acoustic birefringence measurements may be a viable method for the evaluation of total stress in steel members but needs additional research to identify and mitigate the sources of variation in critical acoustic constants that affect the accuracy of the approach.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
Student support for Ahmed Al-Zuheriy was provided by the Higher Committee for Education Development in Iraq (HCED). The opinions, findings, and conclusions or recommendations expressed in this paper are those of the authors and do not necessarily reflect the views of the sponsor. The author also acknowledges the assistance Dr. Paul Fuchs for electronics and software design, and Pedro Ruiz-Fabian, M.S., and undergraduate researchers Juanyuan Ren and Min Chen for assisting with testing, data analysis, and USM system operation.
References
Abé, M. 1998. “Structural monitoring of civil structures using vibration measurement current practice and future.” In Vol. 1454 of Artificial intelligence in structural engineering. Lecture notes in computer science. Berlin: Springer. https://doi.org/10.1007/BFb0030439.
Allen, D., and C. Sayers. 1984. “The measurement of residual stress in textured steel using an ultrasonic velocity combinations technique.” Ultrasonics 22 (4): 179–188. https://doi.org/10.1016/0041-624X(84)90034-9.
Al-Zuheriy, A., S. Orton, and G. Washer. 2020. “Evaluation of total compressive stress in steel W-flange members using ultrasonic shear waves.” J. Perform. Constr. Facil. 34 (6): 04020110. https://doi.org/10.1061/(ASCE)CF.1943-5509.0001520.
ASTM. 2017. Standard specification for steel for structural shapes for use in building framing. ASTM A999. West Conshohocken, PA: ASTM.
Brooks, S. J. 2014. “Ultrasonic biaxial stress measurement for evaluating the adequacy of gusset plates.” M.Sc. thesis, Dept. of Civil and Environmental Engineering, Univ. of Missouri-Columbia.
Brownjohn, J. 2007. “Structural health monitoring of civil infrastructure.” Phil. Trans. R. Soc. A 365 (1851): 589–622.
Castellano, A., A. Fraddosio, S. Marzano, and M. D. Piccioni. 2017. “Some advancements in the ultrasonic evaluation of initial stress states by the analysis of the acoustoelastic effect.” Procedia Eng. 199 (Jan): 1519–1526. https://doi.org/10.1016/j.proeng.2017.09.494.
Clark, A., and J. Moulder. 1985. “Residual stress determination in aluminium using electromagnetic acoustic transducers.” Ultrasonics 23 (6): 253–259. https://doi.org/10.1016/0041-624X(85)90047-2.
Clark, A. V. 1985. “On the use of acoustic birefringence to determine components of plane stress.” Ultrasonics 23 (1): 21–30. https://doi.org/10.1016/0041-624X(85)90007-1.
Clark, A. V., C. S. Hehman, D. Gallagher, M. G. Lozev, and P. A. Fuchs. 1999. “Ultrasonic measurement of stress in pin and hanger connections.” J. Nondestr. Eval. 18 (3): 103–113. https://doi.org/10.1023/A:1021860727643.
Clark, A. V., C. S. Hehman, and T. N. Nguyen. 2000. “Ultrasonic measurement of stress using a rotating EMAT.” Res. Nondestr. Eval. 12 (4): 217–239. https://doi.org/10.1080/09349840009409662.
Clark, A. V., and R. B. Mignogna. 1983. “A comparison of two theories of acoustoelasticity.” Ultrasonics 21 (5): 217–225. https://doi.org/10.1016/0041-624X(83)90045-8.
Crecraft, D. 1967. “The measurement of applied and residual stresses in metals using ultrasonic waves.” J. Sound Vib. 5 (1): 173–192. https://doi.org/10.1016/0022-460X(67)90186-1.
Diankun, L., H. Jingbo, L. Zuohua, and T. Jun. 2018. “Non-destructive evaluation of absolute stress in steel members using shear-wave spectroscopy.” Trans. Nanjing Univ. Aeronaut. Astronaut. 35 (2): 236–243. https://doi.org/10.16356/j.1005-1120.2018.02.236.
Doebling, S. W., C. R. Farrar, M. B. Prime, and D. W. Shevitz. 1996. Damage identification and health monitoring of structural and mechanical systems from changes in their vibration characteristics: A literature review. Los Alamos, NM: Los Alamos National Lab.
Dong, C.-Z., and F. N. Catbas. 2021. “A review of computer vision–based structural health monitoring at local and global levels.” Struct. Health Monit. 20 (2): 692–743. https://doi.org/10.1177/1475921720935585.
Egle, D. M., and D. E. Bray. 1976. “Measurement of acoustoelastic and third-order elastic constants for rail steel.” J. Acoust. Soc. Am. 60 (3): 741–744. https://doi.org/10.1121/1.381146.
Fujino, Y., D. M. Siringoringo, Y. Ikeda, T. Nagayama, and T. Mizutani. 2019. “Research and implementations of structural monitoring for bridges and buildings in Japan.” Engineering 5 (6): 1093–1119. https://doi.org/10.1016/j.eng.2019.09.006.
Gharehbaghi, V. R., E. N. Farsangi, M. Noori, T. Y. Yang, S. Li, A. Nguyen, and S. Mirjalili. 2022. “Critical review on structural health monitoring: Definitions, methods, and perspectives.” Arch. Comput. Methods Eng. 29 (Mar): 2209–2235. https://doi.org/10.1007/s11831-021-09665-9.
He, J., Z. Li, J. Teng, and Y. Wang. 2019. “Comparison of the LCR wave TOF and shear-wave spectrum methods for the uniaxial absolute stress evaluation of steel members.” Struct. Control Health Monit. 26 (6): e2348. https://doi.org/10.1002/stc.2348.
Hwang, Y.-I., H. Lee, Y.-I. Kim, and K.-B. Kim. 2022. “Reliability verification of stress data from extracted specimens using LCR wave stress data from full-section rail specimens.” Meas. Sci. Technol. 33 (7): 075007. https://doi.org/10.1088/1361-6501/ac5b9e.
Iwashimizu, Y., and K. Kubomura. 1973. “Stress-induced rotation of polarization directions of elastic waves in slightly anisotropic materials.” Int. J. Solids Struct. 9 (1): 99–114. https://doi.org/10.1016/0020-7683(73)90035-8.
Jhang, K.-Y., H.-H. Quan, J. Ha, and N.-Y. Kim. 2006. “Estimation of clamping force in high-tension bolts through ultrasonic velocity measurement.” Ultrasonics 44 (Dec): e1339–e1342. https://doi.org/10.1016/j.ultras.2006.05.190.
Karabutov, A., A. Devichensky, A. Ivochkin, M. Lyamshev, I. Pelivanov, U. Rohadgi, and M. Subudhi. 2008. “Laser ultrasonic diagnostics of residual stress.” Ultrasonics 48 (6–7): 631–635. https://doi.org/10.1016/j.ultras.2008.07.006.
Karbhari, V. M., and F. Ansari. 2009. Structural health monitoring of civil infrastructure systems. New York: Elsevier.
Klemme, J. P. 2012. “Ultrasonic stress measurement for evaluating the adequacy of gusset plates.” Masters thesis, Dept. of Civil and Environmental Engineering, Univ. of Missouri-Columbia.
Li, G. Y., A. L. Gower, and M. Destrade. 2020. “An ultrasonic method to measure stress without calibration: The angled shear wave method.” J. Acoust. Soc. Am. 148 (6): 3963–3970. https://doi.org/10.1121/10.0002959.
Li, H.-N., L. Ren, Z.-G. Jia, T.-H. Yi, and D.-S. Li. 2016. “State-of-the-art in structural health monitoring of large and complex civil infrastructures.” J. Civ. Struct. Health Monit. 6 (Feb): 3–16. https://doi.org/10.1007/s13349-015-0108-9.
Li, Z., J. He, D. Liu, N. Liu, Z. Long, and J. Teng. 2019a. “Influence of uniaxial stress on the shear-wave spectrum propagating in steel members.” Sensors 19 (3): 492. https://doi.org/10.3390/s19030492.
Li, Z., J. He, J. Teng, Q. Huang, and Y. Wang. 2019b. “Absolute stress measurement of structural steel members with ultrasonic shear-wave spectral analysis method.” Struct. Health Monit. 18 (1): 216–231. https://doi.org/10.1177/1475921717746952.
Liu, H., Y. Li, T. Li, X. Zhang, Y. Liu, K. Liu, and Y. Wang. 2018. “Influence factors analysis and accuracy improvement for stress measurement using ultrasonic longitudinal critically refracted (LCR) wave.” Appl. Acoust. 141 (Mar): 178–187. https://doi.org/10.1016/j.apacoust.2018.07.017.
Lozev, M. G., A. V. Clark, and P. A. Fuchs. 1996. Application of electromagnetic-acoustic transducers for nondestructive testing in steel bridge structures. Charlottesville, VA: Virginia Transportation Research Council.
Oh, B. K., K. J. Kim, Y. Kim, H. S. Park, and H. Adeli. 2017. “Evolutionary learning based sustainable strain sensing model for structural health monitoring of high-rise buildings.” Appl. Soft Comput. 58 (Mar): 576–585. https://doi.org/10.1016/j.asoc.2017.05.029.
Okada, K. 1980. “Stress-acoustic relations for stress measurement by ultrasonic technique.” J. Acoust. Soc. Jpn. E 1 (3): 193–200. https://doi.org/10.1250/ast.1.193.
Okada, K. 1981. “Acoustoelastic determination of stress in slightly orthotropic materials.” Exp. Mech. 21 (Dec): 461–466. https://doi.org/10.1007/BF02327418.
Ruiz-Fabian, P. 2016. “Development of a portable total-stress measurement instrument.” M.Sc. dissertation, Dept. of Civil and Environmental Engineering.
Sayers, C. M., and D. R. Allen. 1984. “The influence of stress on the principal polarisation directions of ultrasonic shear waves in textured steel plates.” J. Phys. Appl. Phys. 17 (7): 1399. https://doi.org/10.1088/0022-3727/17/7/014.
Schramm, R. E. 1999. “Ultrasonic measurement of stress in railroad wheels.” Rev. Sci. Instrum. 70 (2): 1468–1472. https://doi.org/10.1063/1.1149607.
Sony, S., S. Laventure, and A. Sadhu. 2019. “A literature review of next-generation smart sensing technology in structural health monitoring.” Struct. Control Health Monit. 26 (3): e2321. https://doi.org/10.1002/stc.2321.
Vangi, D. 2001. “Stress evaluation by pulse-echo ultrasonic longitudinal wave.” Exp. Mech. 41 (Sep): 277–281. https://doi.org/10.1007/BF02323145.
Wang, Y., Z. Li, X. Zhu, Y. Gong, N. Liu, Q. Deng, Z. Long, and J. Teng. 2023. “Plane stress measurement on the cross-section of steel components using ultrasonic shear waves.” Mech. Syst. Signal Process. 191 (May): 110185. https://doi.org/10.1016/j.ymssp.2023.110185.
Wang, Y., N. Liu, Y. Gong, X. Zhu, Z. Li, Z. Long, J. Teng, and J. Chen. 2022a. “Three-dimensional stress measurement for structural steel plates using ultrasonic T-waves and P-waves.” Measurement 190 (Feb): 110310. https://doi.org/10.1016/j.measurement.2021.110310.
Wang, Y., X. Zhu, Y. Gong, N. Liu, Z. Li, Z. Long, and J. Teng. 2022b. “Combination of transverse and longitudinal ultrasonic waves for plane stress measurement of steel plates.” Appl. Acoust. 188 (Jan): 108500. https://doi.org/10.1016/j.apacoust.2021.108500.
Washer, G., P. R. Fabian, and P. A. Fuchs. 2017. Development of a portable stress measurement instrument. Washington, DC: Transportation Research Board.
Xu, C., W. Song, Q. Pan, H. Li, and S. Liu. 2015. “Nondestructive testing residual stress using ultrasonic critical refracted longitudinal wave.” Phys. Procedia 70: 594–598. https://doi.org/10.1016/j.phpro.2015.08.030.
Yang, S., M. Wang, and L. Yang. 2019. “Investigation of uncertain factors on measuring residual stress with critically refracted longitudinal waves.” Appl. Sci. 9 (3): 485. https://doi.org/10.3390/app9030485.
Ye, X. W., C. Z. Dong, and T. Liu. 2016. “A review of machine vision-based structural health monitoring: Methodologies and applications.” J. Sens. 2016 (Nov): 7103039. https://doi.org/10.1155/2016/7103039.
Information & Authors
Information
Published In
Copyright
© 2023 American Society of Civil Engineers.
History
Received: Jun 30, 2023
Accepted: Sep 20, 2023
Published online: Dec 12, 2023
Published in print: Feb 1, 2024
Discussion open until: May 12, 2024
ASCE Technical Topics:
- Acoustics
- Continuum mechanics
- Dead loads
- Detection methods
- Dynamics (solid mechanics)
- Engineering fundamentals
- Engineering materials (by type)
- Engineering mechanics
- Field tests
- Laboratory tests
- Live loads
- Materials engineering
- Metals (material)
- Methodology (by type)
- Nondestructive tests
- Seismic waves
- Shear stress
- Shear waves
- Solid mechanics
- Static loads
- Statics (mechanics)
- Steel
- Stress (by type)
- Structural analysis
- Structural engineering
- Tests (by type)
- Waves (mechanics)
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.