Transformation Mechanism of Organic Matter in the Treatment of Petroleum-Based Drilling Cuttings by the Hammermill Thermal Desorption Cutting Treatment System
Publication: Journal of Environmental Engineering
Volume 150, Issue 11
Abstract
Petroleum-based drilling cuttings (PBDCs), as hazardous waste, are characterized by high petroleum pollutant contents and complex compositions and must be properly treated. Their treatment by a hammermill thermal desorption system can generate a variety of products, necessitating better delineation of the transformation characteristics of organic matter at the molecular level. In this study, the transformation characteristics of organic matter in the treatment of PBDCs by a hammermill thermal desorption system have been analyzed by positive-ion atmospheric-pressure photo-ionization Fourier-transform ion cyclotron resonance mass spectrometry (+APPI FT-ICR MS). The results showed that the PBDCs contained large amounts of CH, CHO, and CHON compounds and a small amount of CHS compounds. Of these, CH and CHO compounds are easily separated and recovered by the hammermill thermal desorption treatment system. Most of this organic matter is separated directly through physical changes, whereas only 0.32% undergoes chemical reactions. The organic matter in the recovered petroleum and #110 industrial white oil was highly reproducible and similar in terms of saturation and aromaticity. The mineral composition of the PBDCs did not change significantly during treatment by the hammermill thermal desorption system. This research may provide theoretical guidance for the efficient treatment of PBDCs by the hammermill thermal desorption system.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
This work was supported by a China Postdoctoral Science Foundation funded project (2020M673581XB).
References
Abdul Jameel, A. G., A. B. S. Alquaity, F. Campuzano, A.-H. Emwas, S. Saxena, S. M. Sarathy, and W. L. Roberts. 2021. “Surrogate formulation and molecular characterization of sulfur species in vacuum residues using APPI and ESI FT-ICR mass spectrometry.” Fuel 293 (Jun): 120471. https://doi.org/10.1016/j.fuel.2021.120471.
Abdul-Wahab, S. A., H. Al-Dhamri, G. Ram, and L. Black. 2020. “The use of oil-based mud cuttings as an alternative raw material to produce high sulfate-resistant oil well cement.” J. Cleaner Prod. 269 (Oct): 122207. https://doi.org/10.1016/j.jclepro.2020.122207.
Adhami, S., A. Jamshidi-Zanjani, and A. K. Darban. 2021. “Remediation of oil-based drilling waste using the electrokinetic—Fenton method.” Process Safety Environ. Prot. 149 (May): 432–441. https://doi.org/10.1016/j.psep.2020.11.018.
Chaîneau, C. H., J. L. Morel, and J. Oudot. 1996. “Land treatment of oil-based drill cuttings in an agricultural soil.” J. Environ. Qual. 25 (4): 858–867. https://doi.org/10.2134/jeq1996.00472425002500040030x.
Chen, X., H. Li, L. Zhang, Q. Shi, S. Zhao, and C. Xu. 2020. “Direct sulfur-containing compounds analysis in petroleum via (+) ESI FT-ICR MS using HBF4 as ionization promoter.” Fuel 278 (Oct): 118334. https://doi.org/10.1016/j.fuel.2020.118334.
Chen, X., S. Mu, and Y. Luo. 2023. “Degradation of petroleum pollutants in oil-based drilling cuttings using an Fenton-like advanced oxidation processes.” Environ. Sci. Pollut. Res. 30 (13): 37669–37678. https://doi.org/10.1007/s11356-022-24925-2.
Childs, J. D., E. Acosta, J. F. Scamehorn, and D. A. Sabatini. 2005. “Surfactant-enhanced treatment of oil-based drill cuttings.” J. Energy Resour. Technol. 127 (2): 153–162. https://doi.org/10.1115/1.1879044.
Gu, Z., W. Chen, C. He, and Q. Li. 2022. “Molecular insights into the transformation of refractory organic matter in landfill leachate nanofiltration concentrates during a flocculation and treatment.” J. Hazard. Mater. 435 (Aug): 128973. https://doi.org/10.1016/j.jhazmat.2022.128973.
Han, H., Y. Feng, J. Chen, Q. Xie, S. Chen, M. Sheng, S. Zhong, W. Wei, S. Su, and P. Fu. 2022. “Acidification impacts on the molecular composition of dissolved organic matter revealed by FT-ICR MS.” Sci. Total Environ. 805 (Jan): 150284. https://doi.org/10.1016/j.scitotenv.2021.150284.
Han, Y., M. Noah, V. Lüders, B. Horsfield, and K. Mangelsdorf. 2020. “NSO-compounds in oil-bearing fluid inclusions revealed by FT-ICR-MS in APPI (+) and ESI (−) modes: A new method development.” Org. Geochem. 149 (Nov): 104113. https://doi.org/10.1016/j.orggeochem.2020.104113.
Hao, M., Z. Bai, H. Wang, and W. Liu. 2013. “Removal of oil from electric desalting wastewater using centrifugal contactors.” J. Pet. Sci. Eng. 111 (Nov): 37–41. https://doi.org/10.1016/j.petrol.2013.10.017.
Hou, Y., S. Qi, H. You, Z. Huang, and Q. Niu. 2018. “The study on pyrolysis of oil-based drilling cuttings by microwave and electric heating.” J. Environ. Manage. 228 (Dec): 312–318. https://doi.org/10.1016/j.jenvman.2018.09.040.
Hu, G., H. Liu, C. Chen, H. Hou, J. Li, K. Hewage, and R. Sadiq. 2021. “Low-temperature thermal desorption and secure landfill for oil-based drill cuttings management: Pollution control, human health risk, and probabilistic cost assessment.” J. Hazard. Mater. 410 (May): 124570. https://doi.org/10.1016/j.jhazmat.2020.124570.
Hu, Y., X. Chen, S. Mu, and Q. Li. 2022a. “Extraction and separation of petroleum pollutants from oil-based drilling cuttings using methanol/n-hexane solvent.” Process Saf. Environ. Prot. 168 (Dec): 760–767. https://doi.org/10.1016/j.psep.2022.10.049.
Hu, Y., S. Mu, J. Zhang, and Q. Li. 2022b. “Regional distribution, properties, treatment technologies, and resource utilization of oil-based drilling cuttings: A review.” Chemosphere 308 (Dec): 136145. https://doi.org/10.1016/j.chemosphere.2022.136145.
Ji, G. D., Y. S. Yang, Q. Zhou, T. Sun, and J. R. Ni. 2004. “Phytodegradation of extra heavy oil-based drill cuttings using mature reed wetland: An in situ pilot study.” Environ. Int. 30 (4): 509–517. https://doi.org/10.1016/j.envint.2003.10.003.
Jiang, G., J. Li, L. Zhao, T. Meng, J. Yu, H. Wang, J. Hu, and B. Xu. 2022. “Insights into the deoiling efficiency of oil-based cuttings by surfactant-free microemulsions.” J. Environ. Chem. Eng. 10 (2): 107306. https://doi.org/10.1016/j.jece.2022.107306.
Li, H., S. Li, J. Wu, L. Xie, Y. Liang, Y. Zhang, S. Zhao, C. Xu, and Q. Shi. 2022a. “Molecular characterization of aromatics in petroleum fractions by combining silica sulfuric acid sulfonation with electrospray ionization high-resolution mass spectrometry.” Fuel 317 (Jun): 123463. https://doi.org/10.1016/j.fuel.2022.123463.
Li, Y., U. Pöschl, and M. Shiraiwa. 2016. “Molecular corridors and parameterizations of volatility in the chemical evolution of organic aerosols.” Atmos. Chem. Phys. 16 (5): 3327–3344. https://doi.org/10.5194/acp-16-3327-2016.
Li, Y., B. Zheng, Y. Yang, K. Chen, X. Chen, X. Huang, and X. Wang. 2022b. “Soil microbial ecological effect of shale gas oil-based drilling cuttings pyrolysis residue used as soil covering material.” J. Hazard. Mater. 436 (Aug): 129231. https://doi.org/10.1016/j.jhazmat.2022.129231.
Li, Y.-T., J.-J. Zhang, Y.-H. Li, J.-L. Chen, and W.-Y. Du. 2022c. “Treatment of soil contaminated with petroleum hydrocarbons using activated persulfate oxidation, ultrasound, and heat: A kinetic and thermodynamic study.” Chem. Eng. J. 428 (Jan): 131336. https://doi.org/10.1016/j.cej.2021.131336.
Liu, H., J. Li, M. Zhao, Y. Li, and Y. Chen. 2019. “Remediation of oil-based drill cuttings using low-temperature thermal desorption: Performance and kinetics modeling.” Chemosphere 235 (Nov): 1081–1088. https://doi.org/10.1016/j.chemosphere.2019.07.047.
Liu, Q., Q. Li, N. Wang, D. Liu, L. Zan, L. Chang, X. Gou, and P. Wang. 2018. “Bioremediation of petroleum-contaminated soil using aged refuse from landfills.” Waste Manage. 77 (Jul): 576–585. https://doi.org/10.1016/j.wasman.2018.05.010.
Lv, Q., L. A. Wang, S. Ma, J. Jiang, L. Liu, Z. Zhou, L. Liu, X. Wang, and J. Bai. 2022. “Pyrolysis of oil-based drill cuttings from shale gas field: Kinetic, thermodynamic, and product properties.” Fuel 323 (Sep): 124332. https://doi.org/10.1016/j.fuel.2022.124332.
Mu, S., X. Chen, Y. Luo, and J. Zhang. 2022. “Degradation of petroleum hydrocarbons in oil-based drilling cuttings by a zero-valent iron Fenton-like advanced oxidation system.” Process Saf. Environ. Prot. 168 (Dec): 883–891. https://doi.org/10.1016/j.psep.2022.10.056.
Quintella, C. M., A. M. T. Mata, and L. C. P. Lima. 2019. “Overview of bioremediation with technology assessment and emphasis on fungal bioremediation of oil contaminated soils.” J. Environ. Manage. 241 (Jul): 156–166. https://doi.org/10.1016/j.jenvman.2019.04.019.
Radfarnia, H. R., C. Khulbe, and E. C. Little. 2015. “Supercritical water treatment of oil sludge, a viable route to valorize waste oil materials.” Fuel 159 (Nov): 653–658. https://doi.org/10.1016/j.fuel.2015.06.094.
Shiraiwa, M., T. Berkemeier, K. A. Schilling-Fahnestock, J. H. Seinfeld, and U. Pöschl. 2014. “Molecular corridors and kinetic regimes in the multiphase chemical evolution of secondary organic aerosol.” Atmos. Chem. Phys. 14 (16): 8323–8341. https://doi.org/10.5194/acp-14-8323-2014.
Wang, C.-Q., X.-Y. Lin, M. He, D. Wang, and S.-L. Zhang. 2017a. “Environmental performance, mechanical and microstructure analysis of concrete containing oil-based drilling cuttings pyrolysis residues of shale gas.” J. Hazard. Mater. 338 (Sep): 410–427. https://doi.org/10.1016/j.jhazmat.2017.05.051.
Wang, S., C. Zheng, J. Zhao, X. Li, and H. Lu. 2017b. “Extracting and recovering diesel from oil-based drill cuttings using switchable hydrophilic solvents.” Chem. Eng. Res. Des. 128 (Dec): 27–36. https://doi.org/10.1016/j.cherd.2017.09.036.
Xia, Z., H. Yang, J. Sun, Z. Zhou, J. Wang, and Y. Zhang. 2021. “Co-pyrolysis of waste polyvinyl chloride and oil-based drilling cuttings: Pyrolysis process and product characteristics analysis.” J. Cleaner Prod. 318 (Oct): 128521. https://doi.org/10.1016/j.jclepro.2021.128521.
Xie, B., J. Qin, H. Sun, S. Wang, and X. Li. 2021. “Leaching behavior of polycyclic aromatic hydrocarbons (PAHs) from oil-based residues of shale gas drill cuttings.” Environ. Pollut. 288 (Nov): 117773. https://doi.org/10.1016/j.envpol.2021.117773.
Xu, T., L. A. Wang, H. Wu, D. Jiang, N. Qi, and Z. Gou. 2023. “Municipal solid waste incineration (MSWI) fly ash could be used as a catalyst for pyrolysis of oil-based drill cuttings from shale gas exploitation industry.” J. Cleaner Prod. 387 (Feb): 135754. https://doi.org/10.1016/j.jclepro.2022.135754.
Xu, T., L. A. Wang, H. Zhang, X. Zhan, and Y. Wang. 2022. “Pyrolysis kinetics and environmental risks of oil-based drill cuttings at China’s largest shale gas exploitation site.” Ecotoxicol. Environ. Saf. 246 (Nov): 114189. https://doi.org/10.1016/j.ecoenv.2022.114189.
Yang, H., J. Cai, J. Sun, Z. Zhou, Y. Zhang, and S. Xia. 2021. “Treatment of oil-based drilling cuttings using the demulsification separation—Fenton oxidation method.” Environ. Sci. Pollut. Res. 28 (45): 64307–64321. https://doi.org/10.1007/s11356-021-15509-7.
Yao, G., Z. Chen, Q. Chen, D. Li, Z. Xie, Y. Zhou, X. Xiong, and Y. Xu. 2018. “Behaviors of organic and heavy metallic pollutants during supercritical water oxidation of oil-based drill cuttings.” Water Air Soil Pollut. 229 (3): 102. https://doi.org/10.1007/s11270-018-3751-z.
Zhang, G., F. Zhao, X. Cheng, S. Huang, C. Zhang, M. Zhou, K. Mei, and L. Zhang. 2022. “Resource utilization from solid waste originated from oil-based shale drilling cutting during shale gas development.” Chemosphere 298 (Jul): 134318. https://doi.org/10.1016/j.chemosphere.2022.134318.
Zhang, J., J. Cao, L. Xia, B. Xiang, and E. Li. 2020. “Investigating biological nitrogen cycling in lacustrine systems by FT-ICR-MS analysis of nitrogen-containing compounds in petroleum.” Palaeogeogr. Palaeoclimatol. Palaeoecol. 556 (Oct): 109887. https://doi.org/10.1016/j.palaeo.2020.109887.
Zhou, J., Z. Zhai, J. Wu, W. Yang, and J. Liu. 2023. “Thermal plasma vitrification treatment of oil-based drill cuttings: Product characterization and harmless transformation.” J. Environ. Manage. 331 (Apr): 117285. https://doi.org/10.1016/j.jenvman.2023.117285.
Information & Authors
Information
Published In
Copyright
© 2024 American Society of Civil Engineers.
History
Received: Feb 4, 2024
Accepted: May 28, 2024
Published online: Aug 24, 2024
Published in print: Nov 1, 2024
Discussion open until: Jan 24, 2025
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.