Mechanism of PVA Fiber Influence in Foam Concrete: From Macroscopic to Microscopic View
Publication: Journal of Materials in Civil Engineering
Volume 35, Issue 12
Abstract
Fibers are added to foam concrete to improve its mechanical properties. Despite several studies about the performance of fiber-reinforced foam concretes, the mechanism of fiber reinforcement in foam concretes is not understood. In this research, the microstructural properties of Polyvinyl alcohol (PVA) fiber-reinforced foam concretes were quantitatively analyzed with different fiber sizes and fiber contents. The relationship between different parameters was investigated to understand how and why fibers influence the microstructural properties of foam concrete. In addition, a regression model was developed to analyze how fibers influence the compressive strength and which parameters have the highest impact on the compressive strength. The results show that the mechanism of reinforcement is different in high-density and low-density foam concretes. In high-density foam concrete, fiber distribution had a dominant impact on the compressive strength, but the pore structure did not show much influence on the strength. However, in low-density foam concrete, fiber distribution significantly influenced pore structure, and an improved pore structure provided higher compressive strength. The size of fibers significantly affects fiber reinforcement efficiency. The large-diameter fibers outperformed small-diameter fibers in improving the compressive strength of high-density foam concrete. In contrast, the small-diameter fibers showed better reinforcement efficiency in low-density foam concrete. By optimizing the PVA fiber size and content, the compressive strength of low-density and high-density foam concretes can be improved by 45.3% and 15.5%, respectively.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
Acknowledgments
The authors would also like to acknowledge the support provided by the academic start-up fund from the faculty of engineering at UNSW Sydney.
References
Abdullah, M. A. B., K. A. Mohd Sari, A. R. Mohammed Sani, S. Z. Abd Rahim, M. E. Muhammad Suandi, M. N. Mat Saad, and M. F. Ghazali. 2017. “Applications of foamed lightweight concrete.” In Vol. 97 of Proc., MATEC Web Conf. Les Ulis, France: EDP Science.
Akinpelu, M. A., S. O. Odeyemi, O. S. Olafusi, and F. Z. Muhammed. 2019. “Evaluation of splitting tensile and compressive strength relationship of self-compacting concrete.” J. King Saud Univ. Eng. Sci. 31 (1): 19–25. https://doi.org/10.1016/j.jksues.2017.01.002.
Amran, Y. H. M., N. Farzadnia, and A. A. Abang Ali. 2015. “Properties and applications of foamed concrete; a review.” Constr. Build. Mater. 101 (Dec): 990–1005. https://doi.org/10.1016/j.conbuildmat.2015.10.112.
AS (Australia Standards). 2010. General purpose and blended cements. AS 3972-2010. Sydney, NSW, Australia: AS.
ASTM. 2014. Standard practice for mechanical mixing of hydraulic cement pastes and mortars of plastic consistency. ASTM C305-14. West Conshohocken, PA: ASTM.
ASTM. 2020. Standard test method for compressive strength of hydraulic cement mortars (using 2-in. or [50-mm] cube specimens). ASTM C109/C109M. West Conshohocken, PA: ASTM.
Awang, H., M. A. O. Mydin, and A. F. Roslan. 2012. “Effects of fibre on drying shrinkage, compressive and flexural strength of lightweight foamed concrete.” Adv. Mater. Res 587 (1): 144–149. https://doi.org/10.4028/www.scientific.net/AMR.587.144.
Basha, S. I., M. R. Ali, S. U. Al-Dulaijan, and M. Maslehuddin. 2020. “Mechanical and thermal properties of lightweight recycled plastic aggregate concrete.” J. Build. Eng. 32 (Nov): 101710. https://doi.org/10.1016/j.jobe.2020.101710.
Batool, F., M. Masood Rafi, and V. Bindiganavile. 2021. “Factors influencing the pore structure parameters of lightweight cement-based foams.” J. Test. Eval. 49 (2): 915–932 https://doi.org/10.1520/JTE20180872.
Cheung, P. K., and C. Y. Jim. 2018. “Comparing the cooling effects of a tree and a concrete shelter using PET and UTCI.” Build. Environ. 130 (Feb): 49–61. https://doi.org/10.1016/j.buildenv.2017.12.013.
Chung, S.-Y., C. Lehmann, M. Abd Elrahman, and D. Stephan. 2017. “Pore characteristics and their effects on the material properties of foamed concrete evaluated using Micro-CT images and numerical approaches.” Appl. Sci. 7 (6): 550. https://doi.org/10.3390/app7060550.
Di Leo, G., and F. Sardanelli. 2020. “Statistical significance: p value, 0.05 threshold, and applications to radiomics-reasons for a conservative approach.” Eur Radio. Exp. 4 (1): 18. https://doi.org/10.1186/s41747-020-0145-y.
Ghazi, A. B., A. Jamshidi-Zanjani, and H. Nejati. 2022. “Clinkerisation of copper tailings to replace Portland cement in concrete construction.” J. Build. Eng. 51 (Jul): 104275. https://doi.org/10.1016/j.jobe.2022.104275.
Hannawi, K., H. Bian, W. Prince-Agbodjan, and B. Raghavan. 2016. “Effect of different types of fibers on the microstructure and the mechanical behavior of ultra-high performance fiber-reinforced concretes.” Composites, Part B 86 (Feb): 214–220. https://doi.org/10.1016/j.compositesb.2015.09.059.
Hilal, A. A., N. H. Thom, and A. R. Dawson. 2015. “On entrained pore size distribution of foamed concrete.” Constr. Build. Mater. 75 (Jan): 227–233. https://doi.org/10.1016/j.conbuildmat.2014.09.117.
Jawaid, M., L. Yu, Z. Liu, and E.-R. Kenawy. 2016. “Mechanical properties optimization of fiber reinforced foam concrete.” In Vol. 67 of Proc., MATEC Web Conf. Les Ulis, France: EDP Science.
Jhatial, A. A., W. I. Goh, N. Mohamad, L. W. Hong, M. T. Lakhiar, A. A. A. Samad, and R. Abdullah. 2018. “The mechanical properties of foamed concrete with polypropylene fibres.” Int. J. Eng. Technol. 7 (37): 411–413. https://doi.org/10.14419/ijet.v7i3.7.18892.
Jones, M., and A. McCarthy. 2005. “Behaviour and assessment of foamed concrete for construction applications.” In Proc., Int. Conf. Held at the University of Dundee, Scotland, UK on 5 July 2005, 61–88. London: Thomas Telford Publishing.
Kang, S. T., B. Y. Lee, J.-K. Kim, and Y. Y. Kim. 2011. “The effect of fibre distribution characteristics on the flexural strength of steel fibre-reinforced ultra high strength concrete.” Constr. Build. Mater. 25 (5): 2450–2457. https://doi.org/10.1016/j.conbuildmat.2010.11.057.
Kearsley, E. P., and P. J. Wainwright. 2002. “The effect of porosity on the strength of foamed concrete.” Cem. Concr. Res. 32 (2): 233–239. https://doi.org/10.1016/S0008-8846(01)00665-2.
Lee, B. Y., J.-K. Kim, J.-S. Kim, and Y. Y. Kim. 2009. “Quantitative evaluation technique of Polyvinyl Alcohol (PVA) fiber dispersion in engineered cementitious composites.” Cem. Concr. Compos. 31 (6): 408–417. https://doi.org/10.1016/j.cemconcomp.2009.04.002.
Liu, C., and G. Liu. 2021. “Characterization of pore structure parameters of foam concrete by 3D reconstruction and image analysis.” Constr. Build. Mater. 267 (Jan): 120958. https://doi.org/10.1016/j.conbuildmat.2020.120958.
Liu, Z., K. Zhao, C. Hu, and Y. Tang. 2016. “Effect of water-cement ratio on pore structure and strength of foam concrete.” Adv. Mater. Sci. Eng. 2016 (May): 1–9. https://doi.org/10.1155/2016/9520294.
Mehta, P. K., and P. J. M. Monteiro. 2006. Concrete: Microstructure, properties, and materials. New York: McGraw-Hill.
Nam, J., G. Kim, B. Lee, R. Hasegawa, and Y. Hama. 2016. “Frost resistance of polyvinyl alcohol fiber and polypropylene fiber reinforced cementitious composites under freeze thaw cycling.” Composites, Part B 90 (Apr): 241–250. https://doi.org/10.1016/j.compositesb.2015.12.009.
Nambiar, E. K. K., and K. Ramamurthy. 2007. “Air-void characterisation of foam concrete.” Cem. Concr. Res. 37 (2): 221–230. https://doi.org/10.1016/j.cemconres.2006.10.009.
Nguyen, T. T., H. H. Bui, T. D. Ngo, and G. D. Nguyen. 2017. “Experimental and numerical investigation of influence of air-voids on the compressive behaviour of foamed concrete.” Mater. Des. 130 (Sep): 103–119. https://doi.org/10.1016/j.matdes.2017.05.054.
Pakravan, H. R., and T. Ozbakkaloglu. 2019. “Synthetic fibers for cementitious composites: A critical and in-depth review of recent advances.” Constr. Build. Mater. 207 (May): 491–518. https://doi.org/10.1016/j.conbuildmat.2019.02.078.
Raj, A., D. Sathyan, and K. M. Mini. 2019. “Physical and functional characteristics of foam concrete: A review.” Constr. Build. Mater. 221 (Oct): 787–799. https://doi.org/10.1016/j.conbuildmat.2019.06.052.
Raj, B., D. Sathyan, M. K. Madhavan, and A. Raj. 2020. “Mechanical and durability properties of hybrid fiber reinforced foam concrete.” Constr. Build. Mater. 245 (Jul): 118373. https://doi.org/10.1016/j.conbuildmat.2020.118373.
Rasheed, M. A., and S. S. Prakash. 2015. “Mechanical behavior of sustainable hybrid-synthetic fiber reinforced cellular light weight concrete for structural applications of masonry.” Constr. Build. Mater. 98 (Nov): 631–640. https://doi.org/10.1016/j.conbuildmat.2015.08.137.
Rasheed, M. A., and S. S. Prakash. 2018. “Behavior of hybrid-synthetic fiber reinforced cellular lightweight concrete under uniaxial tension—Experimental and analytical studies.” Constr. Build. Mater. 162 (Feb): 857–870. https://doi.org/10.1016/j.conbuildmat.2017.12.095.
Saleh, E., A. Tarawneh, H. Dwairi, and M. AlHamaydeh. 2022. “Guide to non-destructive concrete strength assessment: Homogeneity tests and sampling plans.” J. Build. Eng. 49 (May): 10404. https://doi.org/10.1016/j.jobe.2022.104047.
Schneider, C. A., W. S. Rasband, and K. W. Eliceiri. 2012. “NIH Image to ImageJ: 25 years of image analysis.” Nat. Methods 9 (7): 671–675. https://doi.org/10.1038/nmeth.2089.
Ting, M. Z. Y., K. S. Wong, M. E. Rahman, and M. Selowarajoo. 2021. “Prediction model for hardened state properties of silica fume and fly ash based seawater concrete incorporating silicomanganese slag.” J. Build. Eng. 41 (Sep): 102356. https://doi.org/10.1016/j.jobe.2021.102356.
Wang, L., S. H. Zhou, Y. Shi, S. W. Tang, and E. Chen. 2017. “Effect of silica fume and PVA fiber on the abrasion resistance and volume stability of concrete.” Composites, Part B 130 (Dec): 28–37. https://doi.org/10.1016/j.compositesb.2017.07.058.
Xue, G., E. Yilmaz, W. Song, and S. Cao. 2019. “Analysis of internal structure behavior of fiber reinforced cement-tailings matrix composites through X-ray computed tomography.” Composites, Part B 175 (Oct): 107091. https://doi.org/10.1016/j.compositesb.2019.107091.
Yu, J. H., and C. Li. 2009. “Research on production, performance and fibre dispersion of PVA engineering cementitious composites.” Mater. Sci. Technol. 25 (5): 651–656. https://doi.org/10.1179/174328408X327731.
Zainorizuan, M. J., et al. 2017. “Microstructure and tensile strength of foamed concrete with added polypropylene fibers.” In Vol. 103 of Proc., MATEC Web Conf. Les Ulis, France: EDP Science.
Zawawi, M. N. A. A., K. Muthusamy, A. P. A. Majeed, R. M. Musa, and A. M. A. Budiea. 2020. “Mechanical properties of oil palm waste lightweight aggregate concrete with fly ash as fine aggregate replacement.” J. Build. Eng. 27 (Jan): 100924. https://doi.org/10.1016/j.jobe.2019.100924.
Zhang, Z., and H. Wang. 2016. “The pore characteristics of geopolymer foam concrete and their impact on the compressive strength and modulus.” Front. Mater. 3 (Aug): 38. https://doi.org/10.3389/fmats.2016.00038.
Information & Authors
Information
Published In
Copyright
© 2023 American Society of Civil Engineers.
History
Received: Dec 6, 2022
Accepted: May 8, 2023
Published online: Sep 25, 2023
Published in print: Dec 1, 2023
Discussion open until: Feb 25, 2024
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.