Optimum Curing Regimes of Early Strength Concrete Inclusive of Heat Transfer and Hydration Effects
Publication: Journal of Materials in Civil Engineering
Volume 35, Issue 7
Abstract
The optimum curing regime (OCR) empirically obtained from a number of small-sized specimens may be overly conservative or inaccurate due to neglecting the effects of exothermic hydration and geometries of full-sized members related to heat transfer. This study presents a theoretical model considering these effects to determine the OCRs of early strength concrete (ESC) in a Pareto set from an extensive design space. To validate the model, experiments were performed to measure the temperature histories and strength development under steam-curing conditions for a full-sized beam segment and match-cured small cylinders made of ESC. Parametric studies showed that energy savings of 7.5%, 20.4%, 42.7%, and 56.3% in steam curing could be achieved with the increase of the maximum steam temperature, sectional area, cooling period in the curing regime, and compressive strength of ESC, respectively. The most significant energy saving, 66.1%, was realized by including the favorable effects of hydration, compared with the results of OCR without hydration for the section considered in this study.
Practical Applications
Approximately 28 days or longer are needed in ambient temperatures for flowable fresh normal concrete to reach its hardened strength. The curing period can be shortened significantly by supplying steam for approximately 12 h at elevated temperatures, which accelerates the chemical reactions between cement particles and water (termed hydration) and allows concrete to reach approximately 70% of the target compressive strength in 1 day. Although steam curing may enhance the production efficiency and quality control, it increases the fuel consumption and intensifies the greenhouse effect. In this study, the heat consumption was reduced by the use of early strength concrete and the beneficial effect of increased temperature of ESC through hydration. Using the proposed steam-curing regimes for ESC, significant energy savings of as much as 66.1% were achieved, compared with those attainable through conventional curing regimes that do not include the hydration effect. The proposed curing technology can be applied to any type of concrete to reduce the energy consumption and greenhouse effects in the precast fabrication industry.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
Acknowledgments
This research was supported by the Basic Science Research Program through the National Research Foundation of Korea (NRF) funded by the Ministry of Education (NRF-2020R1A6A3A01100227) and the Chung-Ang University Graduate Research Scholarship in 2021.
References
ASTM. 2017. Standard practice for estimating concrete strength by the maturity method. ASTM C1074. West Conshohocken, PA: ASTM.
Bentz, D. P. 2010. “Blending different fineness cements to engineer the properties of cement-based materials.” Mag. Concr. Res. 62 (5): 327–338. https://doi.org/10.1680/macr.2008.62.5.327.
Bourchy, A., L. Barnes, L. Bessette, F. Chalencon, A. Joron, and J. M. Torrenti. 2019. “Optimization of concrete mix design to account for strength and hydration heat in massive concrete structures.” Cem. Concr. Compos. 103 (Oct): 233–241. https://doi.org/10.1016/j.cemconcomp.2019.05.005.
Erdogdu, S., and S. Kurbetci. 1998. “Optimum heat treatment cycle for cements of different type and composition.” Cem. Concr. Res. 28 (11): 1595–1604. https://doi.org/10.1016/S0008-8846(98)00134-3.
Hwang, S.-D., R. Khatib, H. K. Lee, S.-H. Lee, and K. H. Khayat. 2012. “Optimization of steam-curing regime for high-strength, self-consolidating concrete for precast, prestressed concrete applications.” PCI J. 57 (3): 48. https://doi.org/10.15554/pcij.06012012.48.62.
Kehl, R. J., and R. L. Carrasquillo. 1998. Investigation of the use of match cure technology in the precast concrete industry. Austin, TX: Univ. of Texas.
Kodur, V. K. R., P. P. Bhatt, P. Soroushian, and A. Arablouei. 2016. “Temperature and stress development in ultra-high performance concrete during curing.” Constr. Build. Mater. 122 (Sep): 63–71. https://doi.org/10.1016/j.conbuildmat.2016.06.052.
Lee, C., S. Lee, and N. Nguyen. 2016a. “Modeling of compressive strength development of high-early-strength-concrete at different curing temperatures.” Int. J. Concr. Struct. Mater. 10 (2): 205–219. https://doi.org/10.1007/s40069-016-0147-6.
Lee, S., and C. Lee. 2020. “Numerical search of the optimum curing regimes for high-early-strength concrete.” J. Mater. Civ. Eng. 32 (4): 04020062. https://doi.org/10.1061/(ASCE)MT.1943-5533.0003144.
Lee, S., N. Nguyen, T. S. Le, and C. Lee. 2016b. “Optimization of curing regimes for precast prestressed members with early-strength concrete.” Int. J. Concr. Struct. Mater. 10 (3): 257–269. https://doi.org/10.1007/s40069-016-0154-7.
McIntosh, J. D. 1956. “The effects of low-temperature curing on the compressive strength of concrete.” In Proc., RILEM Symp. on Winter Concreting. Copenhagen, Denmark: Danish Institute for Building Research.
PCA (Portland Cement Association). 2006. Design and control of concrete mixtures. Skokie, IL: PCA.
PCI (Precast/Prestressed Concrete Institute). 2017. PCI design handbook precast prestressed concrete. 8th ed. Chicago: PCI.
Raju, N. V. S. 2014. Optimization methods for engineers. Delhi, India: PHI Learning.
Ramezanianpour, A. A., M. H. Khazali, and P. Vosoughi. 2013. “Effect of steam curing cycles on strength and durability of SCC: A case study in precast concrete.” Constr. Build. Mater. 49 (Dec): 807–813. https://doi.org/10.1016/j.conbuildmat.2013.08.040.
Reddy, J. N., and D. K. Gartling. 2010. The finite element method in heat transfer and fluid dynamics. New York: CRC Press.
Schindler, A. K., and K. J. Folliard. 2005. “Heat of hydration models for cementitious materials.” ACI Mater. J. 102 (1): 24–33.
Tank, R. C., and N. J. Carino. 1991. “Rate constant functions for strength development of concrete.” ACI Mater. J. 88 (1): 74–83.
Zou, C., G. Long, Y. Xie, J. He, C. Ma, and X. Zeng. 2019. “Evolution of multi-scale pore structure of concrete during steam-curing process.” Microporous Mesoporous Mater. 288 (Jan): 109566. https://doi.org/10.1016/j.micromeso.2019.109566.
Information & Authors
Information
Published In
Copyright
© 2023 American Society of Civil Engineers.
History
Received: Jun 20, 2022
Accepted: Nov 21, 2022
Published online: Apr 26, 2023
Published in print: Jul 1, 2023
Discussion open until: Sep 26, 2023
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.