MPM Simulation of the Installation of an Impact-Driven Pile in Dry Sand and Subsequent Axial Bearing Capacity
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 150, Issue 4
Abstract
Pile installation leads to significant changes in soil state (i.e., void ratio and effective stress) around the pile, which affects stiffness and bearing capacity. Currently, the driveability of piles is analyzed using empirical methods, and the ultimate bearing capacity is estimated without considering the installation effects. This paper presents simulations of the entire installation and subsequent axial bearing capacity of a close-ended pile using a single numerical tool based on the material point method (MPM). A lab-scale experiment is used as a validation case, where the pile is first impact-driven in dry sand, with different initial relative densities (from loose to very dense), and then axially loaded. A state-dependent constitutive model (DeltaSand) is used in the numerical simulations to predict the mechanical behavior of the sand at different relative densities with a single set of input parameters. The paper also illustrates several enhancements needed to obtain more accurate results: (1) an improved contact algorithm that allows gap closure; (2) a rigid-body formulation for the pile body; and (3) a general analytical solution for calculation of energy-consistent impact forces in uncoupled hammer-pile systems.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
The MPM simulations were conducted using a specific version of the Anura3D code, developed in-house by Deltares. Further, the authors would like to thank the anonymous reviewers for their careful and constructive assessment of the manuscript. Their insightful comments and suggestions have greatly enhanced the overall quality of the paper.
References
Al-Kafaji, I. 2013. “Formulation of a dynamic material point method (MPM) for geomechanical problems.” Ph.D. thesis, Fakultät für Bau—und Umweltingenieurwissenschaften, Institut für Geotechnik, Univ. of Stuttgart.
Arroyo, M., J. Bultanska, A. Gens, F. Calvetti, and M. Jamiolkowski. 2011. “Cone penetration tests in a virtual calibration chamber.” Géotechnique 61 (6): 525–531. https://doi.org/10.1680/geot.9.P.067.
Arshad, M., F. S. Tehrani, M. Prezzi, and R. Salgado. 2014. “Experimental study of cone penetration in silica sand using digital image correlation.” Géotechnique 64 (7): 551–569. https://doi.org/10.1680/geot.13.P.179.
Banerjee, R., S. Bandyopadhyay, T. Singh, A. Sengupta, G. Reddy, J. Coleman, and C. Bolisetti. 2022. “An in-house code for studying the response of soil deposits in Mumbai City using 2-D equivalent linear and 1-D nonlinear approach.” Geomech. Geoeng. 17 (1): 220–245. https://doi.org/10.1080/17486025.2020.1728395.
Bardenhagen, S., J. Brackbill, and D. Sulsky. 2000. “The material-point method for granular materials.” Comput. Methods Appl. Mech. Eng. 187 (3–4): 529–541. https://doi.org/10.1016/S0045-7825(99)00338-2.
Bardenhagen, S., J. Guilkey, K. M. Roessig, J. U. Brackbill, W. Witzel, and J. C. Foster. 2001. “An improved contact algorithm for the material point method and application to stress propagation in granular material.” Comput. Model. Eng. Sci. 2 (4): 509–522. https://doi.org/10.3970/cmes.2001.002.509.
Bienen, B., S. Fan, M. Schröder, and M. F. Randolph. 2021. “Effect of the installation process on monopile lateral response.” Proc. Inst. Civ. Eng. Geotech. Eng. 174 (5): 530–548. https://doi.org/10.1680/jgeen.20.00219.
Bolton, M. D. 1986. “The strength and dilatancy of sands.” Géotechnique 36 (1): 65–78. https://doi.org/10.1680/geot.1986.36.1.65.
Borja, R. I. 1988. “Dynamics of pile driving by the finite element method.” Comput. Geotech. 5 (1): 39–49. https://doi.org/10.1016/0266-352X(88)90015-8.
Brinkgreve, R., M. Kappert, and P. Bonnier. 2007. “Hysteretic damping in a small-strain stiffness model.” In Numerical models in geomechanics–NUMOG X, edited by Pande and Pietruszczak, 737–742. London: Taylor & Francis Group.
Ceccato, F., L. Beuth, P. A. Vermeer, and P. Simonini. 2016. “Two-phase material point method applied to the study of cone penetration.” Comput. Geotech. 80 (May): 440–452. https://doi.org/10.1016/j.compgeo.2016.03.003.
Courant, R., K. Friedrichs, and H. Lewy. 1967. “On the partial difference equations of mathematical physics.” IBM J. Res. Dev. 11 (2): 215–234. https://doi.org/10.1147/rd.112.0215.
Fan, S., B. Bienen, and M. F. Randolph. 2021. “Effects of monopile installation on subsequent lateral response in sand. I: Pile installation.” J. Geotech. Geoenviron. Eng. 147 (5): 04021021. https://doi.org/10.1061/(ASCE)GT.1943-5606.0002467.
Fetrati, M., V. Galavi, M. Goodarzi, S. Kreiter, and T. Mörz. 2022. Numerical simulation of CPT in sands using DeltaSand and hardening soil models. Cone Penetration Testing 2022. Boca Raton, FL: CRC Press.
Galavi, V. 2021. “DeltaSand: A state dependent double hardening elasto-plastic model for sand: Formulation and validation.” Comput. Geotech. 129 (Mar): 103844. https://doi.org/10.1016/j.compgeo.2020.103844.
Galavi, V., L. Beuth, B. Z. Coelho, F. S. Tehrani, P. Hölscher, and F. Van Tol. 2017. “Numerical simulation of pile installation in saturated sand using material point method.” Procedia Eng., 175 (Feb): 72–79. https://doi.org/10.1016/j.proeng.2017.01.027.
Galavi, V., M. Martinelli, and A. Elkadi. 2018a. Report of JIP-SIMON project: Enhancement and validation of MPM for simulation of pile driving, WP2: Research development. The Netherlands: Deltares.
Galavi, V., M. Martinelli, P. Ghasemi, A. Elkadi, and R. Thijssen. 2019. “Numerical simulation of impact driven offshore monopiles using the material point method.” In Proc., ECSMGE-2019. London: International Society for Soil Mechanics and Geotechnical Engineering. https://doi.org/10.32075/17ECSMGE-2019-0758.
Galavi, V., F. S. Tehrani, M. Martinelli, A. Elkadi, and D. Luger. 2018b. Axisymmetric formulation of the material point method for geotechnical engineering applications. NUMGE 2018, 427–434. Boca Raton, FL: CRC Press.
Hauser, L., and H. F. Schweiger. 2021. “Numerical study on undrained cone penetration in structured soil using G-PFEM.” Comput. Geotech. 133 (May): 104061. https://doi.org/10.1016/j.compgeo.2021.104061.
Hughes, T. J. R. 1987. The finite element method: Linear static and dynamic finite element analysis. Englewood Cliffs, NJ: Prentice-Hall International.
Jorna, M. M. 2018. “Pile tip deformation caused by obstacles.” M.Sc. thesis, Dept. of Marine Technology, Norwegian Univ. of Science and Technology.
Kulak, R. F., and C. Bojanowski. 2011. “Modeling of cone penetration test using SPH and MM-ALE approaches.” In Proc., 8th European LS-DYNA Users Conf. Livermore, CA: Livermore Software Technology Corporation.
Lee, J. 2008. “Experimental investigation of the load response of model piles in sand.” Ph.D. thesis, Lyles School of Civil Engineering, Purdue Univ.
Lee, J., M. Prezzi, and R. Salgado. 2011. “Experimental investigation of the combined load response of model piles driven in sand.” Geotech. Test. J. 34 (6): 653–667. https://doi.org/10.1520/GTJ103269.
Liao, S. T., and J. M. Roesset. 1997. “Dynamic response of intact piles to impulse loads.” Int. J. Numer. Anal. Methods Geomech. 21 (May): 255–275. https://doi.org/10.1002/(SICI)1096-9853(199704)21:4%3C255::AID-NAG869%3E3.0.CO;2-J.
Martinelli, M., E. Alderlieste, D. Luger, and V. Galavi. 2020. “Numerical simulation of the installation of suction buckets using MPM.” In Proc., 4th Int. Symp. on Frontiers in Offshore Geotechnics (ISFOG 2020 in 2022). Hawthorne, NJ: Deep Foundations Institute.
Martinelli, M., and V. Galavi. 2021. “Investigation of the material point method in the simulation of cone penetration tests in dry sand.” Comput. Geotech. 130 (Feb): 103923. https://doi.org/10.1016/j.compgeo.2020.103923.
Martinelli, M., and V. Galavi. 2022. “An explicit coupled MPM formulation to simulate penetration problems in soils using quadrilateral elements.” Comput. Geotech. 145 (Feb): 104697. https://doi.org/10.1016/j.compgeo.2022.104697.
Martinelli, M., V. Galavi, and A. Elkadi. 2022. “Simulation of gentle pile driving (GDP) using the material point method.” In Proc., 20th Int. Conf. on Soil Mechanics and Geotechnical Engineering, edited by Md. M. Rahman and M. Jaksa, 3259–3264. St Ives, NSW, Australia: Australian Geomechanics Society.
Martinelli, M., and F. Pisanò. 2022. “Relating cone penetration resistance to sand state using the material point method.” Géotech. Lett. 12 (2): 131–138. https://doi.org/10.1680/jgele.21.00145.
Massarsch, K. R. 2005. “Ground vibration caused by impact pile driving.” In Proc., ISEV 2005, 369–379. Japan: Okayama Univ.
Monforte, L., M. Arroyo, J. M. Carbonell, and A. Gens. 2017. “Numerical simulation of undrained insertion problems in geotechnical engineering with the particle finite element method (PFEM).” Comput. Geotech. 82 (Feb): 144–156. https://doi.org/10.1016/j.compgeo.2016.08.013.
Moormann, C., S. Gowda, and S. Giridharan. 2018. “Numerical simulation of pile installation in saturated soil using CPDI.” In Proc., NUMGE 2018, Porto, Portugal.
Oztoprak, S., and M. D. Bolton. 2013. “Stiffness of sands through a laboratory test database.” Géotechnique 63 (1): 54–70. https://doi.org/10.1680/geot.10.P.078.
Perikleous, G., T. Stergiou, and S. Meissl. 2020. “An assessment of the accuracy of SRD methodologies for OWS monopile installation against a north Europe driving records database.” In Proc., 4th Int. Symp. on Frontiers in Offshore Geotechnics (ISFOG 2020 in 2022). Hawthorne, NJ: Deep Foundations Institute.
Rausche, F., G. G. Goble, and J. G. E. Likins. 1985. “Dynamic determination of pile capacity.” J. Geotech. Eng. 111 (3): 367–383. https://doi.org/10.1061/(ASCE)0733-9410(1985)111:3(367).
Salgado, R., and M. Prezzi. 2007. “Computation of cavity expansion pressure and penetration resistance in sands.” Int. J. Geomech. 7 (4): 251–265. https://doi.org/10.1061/(ASCE)1532-3641(2007)7:4(251).
Staubach, P., J. Machaček, J. Skowronek, and T. Wichtmann. 2021. “Vibratory pile driving in water-saturated sand: Back-analysis of model tests using a hydro-mechanically coupled CEL method.” Soils Found. 61 (1): 144–159. https://doi.org/10.1016/j.sandf.2020.11.005.
Sulsky, D., Z. Chen, and H. Schreyer. 1994. “A particle method for history-dependent materials.” Comput. Methods Appl. Mech. Eng. 118 (Feb): 179–196. https://doi.org/10.1016/0045-7825(94)90112-0.
Thevanayagam, S. 2007. “Intergrain contact density indices for granular mixes–II: Liquefaction resistance.” Earthquake Eng. Eng. Vibr. 6 (2): 135–146. https://doi.org/10.1007/s11803-007-0706-6.
Thevanayagam, S., and J. Liang. 2001. “Shear wave velocity relations for silty and gravely soils.” In Proc., 4th Int. Conf. on Recent Advances in Geotechnical Earthquake Engineering and Soil Dynamics, Number 1.36, 1–6. Rolla, MO: Univ. of Missouri.
Thevanayagam, S., T. Shenthan, S. Mohan, and J. Liang. 2002. “Undrained fragility of clean sands, silty sands, and sandy silts.” J. Geotech. Geoenviron. Eng. 128 (10): 849–859. https://doi.org/10.1061/(ASCE)1090-0241(2002)128:10(849).
Vermeer, P. A. 1978. “A double hardening model for sand.” Géotechnique 28 (4): 413–433. https://doi.org/10.1680/geot.1978.28.4.413.
Vugts, J. 2016. Handbook of bottom founded offshore structures. Harelbeke, Belgium: Eburon.
Yost, K. M., M. Martinelli, A. Yerro, R. A. Green, and D. A. de Lange. 2023. “Addressing complexities in MPM modeling of calibration chamber cone penetrometer tests in homogenous and highly interlayered soils.” Comput. Geotech. 158 (Jun): 105378. https://doi.org/10.1016/j.compgeo.2023.105378.
Zambrano-Cruzatty, L., and A. Yerro. 2020. “Numerical simulation of a free fall penetrometer deployment using the material point method.” Soils Found. 60 (3): 668–682. https://doi.org/10.1016/j.sandf.2020.04.002.
Information & Authors
Information
Published In
Copyright
© 2024 American Society of Civil Engineers.
History
Received: Dec 29, 2022
Accepted: Oct 18, 2023
Published online: Feb 8, 2024
Published in print: Apr 1, 2024
Discussion open until: Jul 8, 2024
ASCE Technical Topics:
- Axial loads
- Density (material)
- Effective stress
- Engineering fundamentals
- Engineering mechanics
- Foundation design
- Foundations
- Geomechanics
- Geotechnical engineering
- Load bearing capacity
- Material mechanics
- Material properties
- Materials engineering
- Models (by type)
- Numerical models
- Pile foundations
- Piles
- Sandy soils
- Soil mechanics
- Soil properties
- Soil stress
- Soils (by type)
- Static loads
- Statics (mechanics)
- Stress (by type)
- Structural analysis
- Structural engineering
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.