Analytical Investigation of Fatigue Behavior in a Modified Composite Steel Box Concrete Girder Bridge with Corrugated Steel Webs under Pavement and Expansion Joint Deterioration
Publication: Journal of Bridge Engineering
Volume 29, Issue 10
Abstract
In this study, the numerical investigation of the fatigue impact factor of critical structural details near the expansion joint for a modified composite steel box concrete girder bridge with corrugated steel webs (MCSBCGBCSW) was conducted using a vehicle–bridge coupled vibration system (VBCVS). Within the VBCVS framework, the MCSBCGBCSW served as the bridge model, and the three-axle vehicle model was employed as the fatigue vehicle loading model. Additionally, deterioration models for pavement roughness and expansion joints were established. The stress impact coefficient IMS and stress amplitude impact coefficient IMR of critical structural details near the expansion joint were investigated in detail, considering various vehicle speeds, pavement roughness conditions (PRCs), and expansion joint deterioration degrees (EJDDs). The results demonstrate that the most critical factor affecting IMS and IMR of the critical structural details near the expansion joint is the deterioration degree of the PRC rather than the vehicle speed or EJDD, with maximum values of 4.943 and 8.682, respectively, when the PRC is very poor. When the distance between the critical structural details and the expansion joint is within 6 m, a greater dynamic impact action is observed, with a maximum value of 4.067. The fluctuation range of IMR between the critical structural details decreases and stabilizes as the distance between these details and the expansion joint exceeds 6 m. Based on the IMR of the critical structural details near the expansion joint, a calculation formula for the design value of IMR was developed for an MCSBCGBCSW, with a confidence level of 95% compared to the values stipulated by the American Association of State Highway and Transportation Officials specification. These results provide reference information for calculating the IMR of the critical structural details near expansion joints for MCSBCGBCSWs.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, or codes that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
National Natural Science Foundation of China (52168019), Fundamental Research Funds for Central Universities (541109030099), Gansu Provincial Key R&D Plan-Industrial Project Funding (23YFGA0043), and Hunan Provincial Natural Science Foundation General Project (2024JJ5084).
References
AASHTO. 2017. AASHTO LRFD bridge design specifications. 8th ed. Washington, DC: AASHTO.
Abdelaziz, N., R. T. Abd El-Hakim, S. M. El-Badawy, and H. A. Afify. 2020. “International roughness index prediction model for flexible pavements.” Int. J. Pavement Eng. 21 (1): 88–99. https://doi.org/10.1080/10298436.2018.1441414.
Chen, B. C., Y. M. Mu, Y. Y. Chen, and J. Huang. 2013. “State-of-the-art of research and engineering application of steel–concrete composite bridges in China.” [In Chinese.] J. Build. Struct. 34 (1): 1–10.
Chen, Y. Y., J. Dong, Z. Tong, R. Jiang, and Y. Yue. 2020. “Flexural behavior of composite box girders with corrugated steel webs and trusses.” Eng. Struct. 209: 110275. https://doi.org/10.1016/j.engstruct.2020.110275.
Cui, S. A., M. Zhang, G. Zeng, L. Shen, J. Su, and B. Zhu. 2023. “Fatigue performance assessment of double-deck six-line railway bridge based on vehicle–bridge coupling vibration.” [In Chinese.] J. Southeast Univ. (Sci. Technol.) 53 (1): 67–75.
Deng, L., and C. S. Cai. 2010. “Development of dynamic impact factor for performance evaluation of existing multi-girder concrete bridges.” Eng. Struct. 32 (1): 21–31. https://doi.org/10.1016/j.engstruct.2009.08.013.
Deng, L., Y. X. Chen, W. S. Han, and W. Wang. 2020. “Studying impact factors for short- and medium-span simply supported concrete highway bridges and its suggested values.” [In Chinese.] China J. Highway Transp. 33 (1): 69–78.
Deng, L., W. He, and Y. Shao. 2015. “Dynamic impact factors for shear and bending moment of simply supported and continuous concrete girder bridges.” J. Bridge Eng. 20 (11): 1–9. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000744.
Deng, L., and F. Wang. 2015. “Study of the dynamic responses and impact factors of simply-supported prestressed concrete girder bridges due to vehicle braking.” [In Chinese.] J. Hunan Univ. (Sci. Technol.) 42 (9): 52–58.
Ding, Y., L. X. Han, J. H. Lyu, P. Zhuge, B. Wang, and D.B. Yu. 2021. “Fatigue life analysis and structural optimization of modular bridge expansion joint.” China J. Highway Transp. 34 (2): 265–275.
Ding, Y., Q. Huang, X. Xie, and J. Huang. 2013. “A computational method for the dynamic load in heavy-vehicle bumping at the bridge expansion joint and analysis of the influencing factors.” China Civ. Eng. J. 46 (7): 98–107.
Ding, Y., D. B. Yu, Y. Y. Zou, and Wang B. 2018. “Analysis of impact load and coupling vibration of vehicle and modular bridge expansion joint.” China J. Highway Transp. 31 (7): 167–178.
Ding, Y., W. Zhang, and F. T. K. Au. 2016. “Effect of dynamic impact at modular bridge expansion joints on bridge design.” Eng. Struct. 127: 645–662. https://doi.org/10.1016/j.engstruct.2016.09.007.
González, A., D. Cantero, and E. J. Obrien. 2011. “Dynamic increment for shear force due to heavy vehicles crossing a highway bridge.” Comput. Struct. 89 (23–24): 2261–2272. https://doi.org/10.1016/j.compstruc.2011.08.009.
Huang, D. 2012. “Vehicle-induced vibration of steel deck arch bridges and analytical methodology.” J. Bridge Eng. 17 (2): 241–248. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000243.
Huang, D. Z. 2001. “Dynamic analysis of steel curved box girder bridges.” J. Bridge Eng. 6 (6): 506–513. https://doi.org/10.1061/(ASCE)1084-0702(2001)6:6(506).
Huang, D. Z., T. L. Wang, and M. Shahawy. 1992. “Impact analysis of continuous multigirder bridges due to moving vehicles.” J. Struct. Eng. 118 (12): 3427–3443. https://doi.org/10.1061/(ASCE)0733-9445(1992)118:12(3427).
Huang, H. M., Y. H. Zhang, W. Ji, and K. Luo. 2022. “Theoretical study and parametric analysis on restrained torsion of composite box girder bridge with corrugated steel webs.” J. Bridge Eng. 27 (12): 04022118. https://doi.org/10.1061/(ASCE)BE.1943-5592.0001963.
ISO (International Organization for Standardization). 1995. Mechanical vibration-road surface profiles—Reporting of measured data. ISO 8608: 1995(E). Geneva: ISO.
Ji, W., Q. Bai, W. Wang, and Q. J. Li. 2023. “Fatigue study on improved composite box girder bridge with corrugated steel webs.” J. Constr. Steel Res. 213: 108380. https://doi.org/10.1016/j.jcsr.2023.108380.
Ji, W., S. H. Hu, Z. F. Qi, K. Luo, and J. Zhang. 2022. “Dynamic characteristics analysis of box girder bridges with corrugated steel webs.” [In Chinese.] J. Vib. Meas. Diagn. 45 (5): 886–892.
Ji, W., and T. Y. Shao. 2021a. “Finite element model updating for improved box girder bridges with corrugated steel webs using the response surface method and fmincon algorithm.” KSCE J. Civ. Eng. 25 (2): 586–602. https://doi.org/10.1007/s12205-020-0591-3.
Ji, W., and T. Y. Shao. 2021b. “Finite element model updating of box girder bridges with corrugated steel webs.” J. Southwest Jiaotong Univ. 56 (1): 1, 11. https://doi.org/10.35741/issn.0258-2724.56.1.1.
Kanchanadevi, A., K. Ramanjaneyulu, and P. Gandhi. 2021. “Shear resistance of embedded connection of composite girder with corrugated steel web.” J. Constr. Steel Res. 187: 106994. https://doi.org/10.1016/j.jcsr.2021.106994.
Kim, C. W., M. Kawatani, and Y. R. Kwon. 2007. “Impact coefficient of reinforced concrete slab on a steel girder bridge.” Eng. Struct. 29 (4): 576–590. https://doi.org/10.1016/j.engstruct.2006.05.021.
Kong, X., K. Luo, W. Ji, Q. Tang, and L. Deng. 2022. “Study on dynamic characteristics of an improved composite box girder with corrugated steel webs.” J. Bridge Eng. 27 (6): 04022035. https://doi.org/10.1061/(ASCE)BE.1943-5592.0001877.
Li, H. L., H. Xia, N. Zhang, X. Du, and Y. Hou. 2017. “Assessment of fatigue damage and remaining life of steel bridges based on train-bridge coupling dynamic analysis.” [In Chinese.] J. China Railway Soc. 39 (1): 104–110.
Lu, N. W., Y. Liu, and Y. Deng. 2015. “Fatigue damage and life assessment for steel decks of suspension bridge under stochastic traffic flow.”[In Chinese.] J. Central South Univ. (Sci. Technol.) 46 (11): 4300–4306.
Ma, Y., J. Yang, and D. L. Wang. 2019. “Vehicle loading study of Hangzhou Bay cross-sea bridge.” [In Chinese.] Shanghai Highway 4: 28–31+3.
MOT (Ministry of Transport). 2018. Highway performance assessment standards. JTG 5210-2018. Beijing: MOT.
Nie, J. G., M. X. Tao, L. L. Wu,X. Nie, F. Li, and F. Lei. 2012. “Advances of research on steel–concrete composite bridges.” [In Chinese.] China Civ. Eng. J. 45 (6): 110–122.
Nie, J. G., Y. J. Zhu, M. X. Tao, C. R. Guo, and Y. X. Li. 2017. “Optimized prestressed continuous composite girder bridges with corrugated steel webs.” J. Bridge Eng. 22 (2): 04016121. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000995.
OBrien, E. J., D. Cantero, B. Enright, and A. González. 2010. “Characteristic dynamic increment for extreme traffic loading events on short and medium span highway bridges.” Eng. Struct. 32 (12): 3827–3835. https://doi.org/10.1016/j.engstruct.2010.08.018.
Paterson, W. 1986. International roughness index: Relationship to other measures of roughness and riding quality. In Proc., 65th Annual Meeting of the Transportation Research Board, 49–59. Washington, DC: Transportation Research Record.
Shi, F., D. Wang, and L. Chen. 2021. “Study of flexural vibration of variable cross-section box-girder bridges with corrugated steel webs.” Structures 33: 1107–1118. https://doi.org/10.1016/j.istruc.2021.05.004.
Shiyab, A. M. 2007. “Optimum use of the flexible pavement condition indicators in pavement management system.” PhD. thesis, School of Civil Engineering, Curtin Univ. of Technology.
Wang, T. L., D. Z. Huang, and M. Shahawy. 1996. “Dynamic behavior of continuous and cantilever thin-walled box girder bridges.” J. Bridge Eng. 1 (2): 67–75. https://doi.org/10.1061/(ASCE)1084-0702(1996)1:2(67).
Wang, W. 2017. Study on the fatigue of steel–concrete composite bridges based on vehicle–bridge coupled vibration. Changsha: Hunan Univ.
Wang, W., W. C. Yan, L. Deng, and H. Kang. 2015. “Dynamic analysis of a cable-stayed concrete-filled steel tube arch bridge under vehicle loading.” J. Bridge Eng. 20 (5): 1–12. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000675.
Wang, Z. Y., and Q. Y. Wang. 2014. “Fatigue assessment of welds joining corrugated steel webs to flange plates.” Eng. Struct. 73: 1–12. https://doi.org/10.1016/j.engstruct.2014.04.041.
Yan, W. C. 2015. “Study of vehicle–road–bridge vibration caused by the road and bridge unevenness at the end of the bridge.” Master’s thesis, School of Civil Engineering, Hunan Univ.
Ye, M., L. Li, D. Y. Yoo, L. Wang, H. Li, and C. Zhou. 2023. “Shear performance of prestressed composite box beams with ultra-high-performance concrete and corrugated steel webs under different loading conditions.” Thin-Walled Struct. 186: 110675. https://doi.org/10.1016/j.tws.2023.110675.
Zhang, H., L. Li, W. Ma, Y. Luo, Z. Li, and H. Kuai. 2022. “Effects of welding residual stresses on fatigue reliability assessment of a pc beam bridge with corrugated steel webs under dynamic vehicle loading.” Structures 45: 1561–1572. https://doi.org/10.1016/j.istruc.2022.09.094.
Zhang, P. F., L. Shi, J. W. Chen, R. F. Zhu, and W. Zhang. 2021. “Experiment and simulation study on influence of bridge surface roughness on vibration of through tie arch bridge.” [In Chinese.] China J. Highway Transp. 34 (2): 199–210.
Zhang, W., and C. S. Cai. 2012. “Fatigue reliability assessment for existing bridges considering vehicle speed and road surface conditions.” J. Bridge Eng. 17 (3): 443–453. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000272.
Zhang, W., and C. S. Cai. 2013. “Reliability-based dynamic amplification factor on stress ranges for fatigue design of existing bridges.” J. Bridge Eng. 18 (6): 538–552. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000387.
Zhou, C., L. F. Li, and L. H. Wang. 2019. “Improved softened membrane model for prestressed composite box girders with corrugated steel webs under pure torsion.” J. Constr. Steel Res. 153: 372–384. https://doi.org/10.1016/j.jcsr.2018.10.023.
Zhou, Y. J., Y. Zhao, Y. Zhao, Q. Cao, and Z. Li. 2021. “A study on dynamic load allowance of a simply supported girder bridge based on load efficiency of a dynamic load test.” [In Chinese.] J. Vib. Shock 40 (20): 207–216.
Zhu, J. S., C. Xiang, and H. D. Qi. 2021. “Fatigue damage evaluation of steel–concrete composite beam of long-span suspension bridge considering vehicle–bridge coupled effect.” [In Chinese.] J. Vib. Shock 40 (5): 218–229.
Zhu, Z. H., Q. S. Feng, W. Gong, L. Jiang, and Z. Yu. 2019. “Local fatigue analysis of heavy-haul railway steel bridge based on train–bridge coupled vibration.” [In Chinese.] J. Railway Eng. Soc 36 (9): 36–42+78.
Information & Authors
Information
Published In
Copyright
© 2024 American Society of Civil Engineers.
History
Received: Feb 8, 2024
Accepted: Jun 6, 2024
Published online: Aug 5, 2024
Published in print: Oct 1, 2024
Discussion open until: Jan 5, 2025
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.