Impact of Lower Protective Coal Seam Mining on Overlying Strata: Deformation, Pressure Relief, and Permeability Enhancement
Publication: International Journal of Geomechanics
Volume 24, Issue 9
Abstract
This study focuses on the issue of gas overflow encountered during the mining of coal seams at the Anshun coal mine. Initially, a mechanical model is constructed to analyze the displacement and vertical stress distribution in the upper neighboring coal seam following the mining of the protective seam in the field. Subsequently, similar indoor simulation experiments, utilizing the digital image correlation method, are conducted to examine the evolution characteristics of the overlying rock strain during the back mining process of the lower protective seam. Numerical simulation is then employed to analyze the plastic zone, stress distribution, and evolution characteristics of the overlying coal seam during the recovery of the lower protective layer. The study finally investigates the unloading effect of the top plate and the permeability characteristics of the protected layer. The results demonstrate that the maximum main strain concentration area in the overlying rock increases as the working face progresses, transferring asymmetrically from the middle of the mining area to the cuthole side and the working face side, with the concentration on the cuthole side being notably larger. As the lower protective layer advances, the unloading range, unloading height, stress concentration area, peak value, and unloading coefficient are observed to increase gradually before stabilizing. The numerical simulation reveals a predominance of shear damage around the mining area, where high permeability facilitates gas flow. Additionally, the collapsed gangue in the mining area's center is recompacted, leading to reduced porosity and permeability. Stress concentration is noted on both sides of the coal seam, resulting in high stress at both ends and low stress in the middle of the unloading area. Furthermore, the permeability coefficient growth rate diminishes with the advancement of the lower protection layer, exhibiting negative growth in some areas, while the permeability coefficient in the unloading area remains high at the late stage of workface recovery, thereby constituting an efficient gas extraction zone. This study provides a theoretical foundation for the safe and efficient mining of protruding coal seams in southwest China.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and codes generated or used during the study appear in the published paper.
Acknowledgments
The authors thank the editor and anonymous reviewers for their valuable advices. We acknowledge the financial support from the Guizhou Provincial Basic Research Program (Natural Science) (Qianke He Foundation-ZK [2024] Key 022), Qiankehe Platform Talents, Grant/Award Number: (GCC [2023] 056), Guizhou Provincial Department of Education 2023 Annual College Science and Technology Innovation Team (Guizhou Education Technology [2023] 055), Guizhou Provincial Science and Technology Projects (Qianke Science Support [2021] General 399), and the National Natural Science Foundation of China (Nos. 52064005, 52164002, and 52164005). Finally, the first author would like to thank the Senior sister Wendylitoutou for correcting the grammar of the paper and organizing the charts.
References
Abdelatif, A. O., J. S. Owen, and M. F. M. Hussein. 2020. “A novel test method for tendon re-anchorage in bonded post tensioned concrete using ESPI full field measurement.” Mater. Struct. 53 (3): 59. https://doi.org/10.1617/s11527-020-01495-8.
Cao, W., H. Liu, Y. Hang, H. Wang, and G. Li. 2022. “Similarity simulation on the movement characteristics of surrounding rock and floor stress distribution for large-dip coal seam.” Sensors 22 (7): 2761. https://doi.org/10.3390/s22072761.
Chen, B., and B. Pan. 2018. “Full-field surface 3D shape and displacement measurements using an unfocused plenoptic camera.” Exp. Mech. 58 (5): 831–845. https://doi.org/10.1007/s11340-018-0383-6.
Cheng, X., G. Zhao, Y. Li, X. Meng, Q. Tu, S. Huang, and Z. Qin. 2021. “Mining-induced pressure-relief mechanism of coal–rock mass for different protective layer mining modes.” Adv. Mater. Sci. Eng. 2021: 1–15. https://doi.org/10.1155/2021/3598541.
Cheng, Z., L.-H. Li, and Y.-N. Zhang. 2020. “Laboratory investigation of the mechanical properties of coal–rock combined body.” Bull. Eng. Geol. Environ. 79 (4): 1947–1958. https://doi.org/10.1007/s10064-019-01613-z.
Cheng, Z., W. Pan, X. Li, and W. Sun. 2019a. “Numerical simulation on strata behaviours of TCCWF influenced by coal–rock combined body.” Geomech. Eng. 19 (3): 269–282. https://doi.org/10.12989/gae.2019.19.3.269.
Cheng, Z., S. Yang, L. Li, and L. Zhang. 2019b. “Support working resistance determined on top-coal caving face based on coal–rock combined body.” Geomech. Eng. 19 (3): 255–268. https://doi.org/10.12989/gae.2019.19.3.255.
Fang, S. J., B. Liang, W. J. Sun, Z. S. Shi, J. F. Hao, B. F. Wang, and X. Y. Zhang. 2022. “Study on stress evolution law of overburden under repeated mining in long-distance double upper protective layer.” Energies 15 (12): 4459. https://doi.org/10.3390/en15124459.
Guo, P., T. Wang, D. Li, and X. Zhou. 2016. “How energy technology innovation affects transition of coal resource-based economy in China.” Energy Policy 92: 1–6. https://doi.org/10.1016/j.enpol.2016.01.026.
He, X., K. Yang, L. Yuan, C. Zhang, and T. Zhang. 2020. “Experimental study of pressure-relief and permeability improvement effect of the remote protected layer crossing coal groups with double key strata.” Zhongguo Kuangye Daxue Xuebao/J. China Univ. Min. Technol. 49 (2): 238–246.
Huang, K., L. Xu, F. Zha, Z. Lu, J. Wu, C. Chu, and C. Yu. 2021. “Similarity simulation study on displacement and stress changes response to coal mining in Longdong coal mine, China.” Q. J. Eng. Geol. Hydrogeol. 54 (4): qjegh2020-111, https://doi.org/10.1144/qjegh2020-111.
Jiang, J., and B. Xu. 2018. “Study on the development laws of bed-separation under the hard-thick magmatic rock and its fracture disaster-causing mechanism.” Geotech. Geol. Eng. 36 (3): 1525–1543. https://doi.org/10.1007/s10706-017-0406-6.
Jin, K., Y. P. Cheng, W. Wang, H. B. Liu, Z. D. Liu, and H. Zhang. 2016. “Evaluation of the remote lower protective seam mining for coal mine gas control: A typical case study from the Zhuxianzhuang Coal Mine, Huaibei Coalfield, China.” J. Nat. Gas Sci. Eng. 33: 44–55. https://doi.org/10.1016/j.jngse.2016.05.004.
Kong, D., Q. Li, G. Wu, and G. Song. 2021a. “Characteristics and control technology of face-end roof leaks subjected to repeated mining in close-distance coal seams.” Bull. Eng. Geol. Environ. 80 (11): 8363–8383. https://doi.org/10.1007/s10064-021-02438-5.
Kong, D., Y. Xiong, Z. Cheng, N. Wang, G. Wu, and Y. Liu. 2021b. “Stability analysis of coal face based on coal face-support-roof system in steeply inclined coal seam.” Geomech. Eng. 25 (3): 233–243. https://doi.org/10.12989/gae.2021.25.3.233.
Kong, D.-Z., Z.-B. Cheng, and S.-S. Zheng. 2019. “Study on the failure mechanism and stability control measures in a large-cutting-height coal mining face with a deep-buried seam.” Bull. Eng. Geol. Environ. 78 (8): 6143–6157. https://doi.org/10.1007/s10064-019-01523-0.
Li, L., G. Wu, and Q. Liu. 2022. “Study on overburden movement and fissure evolution law of protective layer mining in shallow coal seam.” Energies 15 (5): 1831. https://doi.org/10.3390/en15051831.
Li, Z., Z. Hui, and G. Hao. 2017. “A case study of gas drainage to low permeability coal seam.” Int. J. Min. Sci. Technol. 27 (4): 687–692. https://doi.org/10.1016/j.ijmst.2017.05.014.
Liu, A. X., S. H. Tu, F. T. Wang, Y. Yuan, C. Zhang, and Y. W. Zhang. 2013. “Numerical simulation of pressure relief rule of upper and lower protected coal-seam in thin-protective-seam mining.” Disaster Adv. 6: 16–25.
Lv, H., Z. Cheng, Y. Dong, J. Zhang, and Y. Ma. 2021a. “Numerical simulation on the crack initiation and propagation of coal with combined defects.” Struct. Eng. Mech. 79 (2): 237–245. https://doi.org/10.12989/sem.2021.79.2.237.
Lv, H., Z. Cheng, and F. Liu. 2021b. “Study on the mechanism of a new fully mechanical mining method for extremely thick coal seam.” Int. J. Rock Mech. Min. Sci. 142: 104788. https://doi.org/10.1016/j.ijrmms.2021.104788.
Lv, H., Y. Tang, L. Zhang, Z. Cheng, and Y. Zhang. 2019. “Analysis for mechanical characteristics and failure models of coal specimens with non-penetrating single crack.” Geomech. Eng. 17 (4): 355–365. https://doi.org/10.12989/gae.2019.17.4.355.
Rezaei, M., M. F. Hossaini, and A. Majdi. 2015. “Determination of longwall mining-induced stress using the strain energy method.” Rock Mech. Rock Eng. 48 (6): 2421–2433. https://doi.org/10.1007/s00603-014-0704-8.
Shang, Y., G. Wu, Q. Liu, D. Kong, and Q. Li. 2021. “The drainage horizon determination of high directional long borehole and gas control effect analysis.” Adv. Civ. Eng. 2021: 1–11. https://doi.org/10.1155/2021/3370170.
Shang, Y., L. Zhang, D. Kong, Y. Wang, and Z. Cheng. 2023. “Overlying strata failure mechanism and gas migration law in close distance outburst coal seams: A case study.” Eng. Fail. Anal. 148: 107214. https://doi.org/10.1016/j.engfailanal.2023.107214.
Tu, Q., and Y. Cheng. 2019. “Stress evolution and coal seam deformation through the mining of a remote upper protective layer.” Energy Sources Part A 41 (3): 338–348. https://doi.org/10.1080/15567036.2018.1518352.
Wang, D., G. Barakos, Z. Cheng, H. Mischo, and J. Zhao. 2023a. “Numerical simulation of pressure profile of mining backfill fly-ash slurry in an L-shaped pipe using a validated Herschel–Bulkley model.” J. Sustainable Cem.-Based Mater. 12 (3): 219–233. https://doi.org/10.1080/21650373.2021.2012723.
Wang, D., E. Wang, X. Feng, M. Wei, D. Li, Q. Liu, B. Li, and X. Zhang. 2022a. “Triaxial creep damage-catastrophe instability characteristics and a nonlinear constitutive model of gas-bearing coal.” Bull. Eng. Geol. Environ. 81 (10): 437. https://doi.org/10.1007/s10064-022-02931-5.
Wang, F., Y. Liang, X. Li, L. Li, J. Li, and Y. Chen. 2019. “Study on the change of permeability of gas-containing coal under many factors.” Energy Sci. Eng. 7 (1): 194–206. https://doi.org/10.1002/ese3.269.
Wang, K., and F. Du. 2020. “Coal-gas compound dynamic disasters in China: A review.” Process Saf. Environ. Prot. 133: 1–17. https://doi.org/10.1016/j.psep.2019.10.006.
Wang, L., Z. Wang, S. Xu, W. Zhou, and J. Wu. 2015. “A field investigation of the deformation of protected coal and its application for CBM extraction in the Qinglong coalmine in China.” J. Nat. Gas Sci. Eng. 27: 367–373. https://doi.org/10.1016/j.jngse.2015.08.066.
Wang, W., F. Wen, Y. Yang, and Y. Jia. 2022b. “Study of the impact of the rise and fall of the coal industry on the regional economy.” J. Global Inf. Manage. 30 (6): 1–17. https://doi.org/10.4018/JGIM.302655.
Wang, Y. W., H. H. Yuan, M. Z. Gao, M. H. Li, and J. G. Sun. 2023b. “Fracture law of different overlying strata in mining of protective seam under close distance coal seam.” Energy Sci. Eng. 11 (3): 1336–1348. https://doi.org/10.1002/ese3.1396.
Xia, X., X. Zhang, and C. Mu. 2021. “A multi-camera based photogrammetric method for three-dimensional full-field displacement measurements of geosynthetics during tensile test.” Geotext. Geomembr. 49 (5): 1192–1210. https://doi.org/10.1016/j.geotexmem.2021.03.012.
Xie, X. P., X. Q. Fang, M. F. Liang, and D. C. Ai. 2020. “Geological evolution process, mechanism, and application of protective layer in semi-coal and rock face.” Earth Sci. Res. J. 24 (4): 499–506. https://doi.org/10.15446/esrj.v24n4.91378.
Xue, Y., F. Gao, and X. Liu. 2015. “Effect of damage evolution of coal on permeability variation and analysis of gas outburst hazard with coal mining.” Nat. Hazards 79 (2): 999–1013. https://doi.org/10.1007/s11069-015-1888-2.
Yang, M., M. Wang, Y. Wang, J. Zhang, L. Zhang, and Z. Wang. 2022. “Coal pore structure changes in upper protective seam after mining: Pingdingshan Shenma Group, Henan Province, China.” J. Pet. Sci. Eng. 218: 111045. https://doi.org/10.1016/j.petrol.2022.111045.
Yang, W., W. Wang, R. Jia, G. Walton, S. Sinha, Q. Chen, B. Lin, and X. Jiao. 2023. “Parameter optimization of coal face blasting for coal and gas outburst control.” Bull. Eng. Geol. Environ. 82 (3): 80. https://doi.org/10.1007/s10064-023-03086-7.
Zhang, H., Z. Wen, B. Yao, and X. Chen. 2020. “Numerical simulation on stress evolution and deformation of overlying coal seam in lower protective layer mining.” Alexandria Eng. J. 59 (5): 3623–3633. https://doi.org/10.1016/j.aej.2020.06.011.
Zhang, X., and J. Zou. 2022. “Research on collaborative control technology of coal spontaneous combustion and gas coupling disaster in goaf based on dynamic isolation.” Fuel 321: 124123. https://doi.org/10.1016/j.fuel.2022.124123.
Zheng, C., M. S. Kizil, S. M. Aminossadati, and Z. Chen. 2018. “Effects of geomechanical properties of interburden on the damage-based permeability variation in the underlying coal seam.” J. Nat. Gas Sci. Eng. 55: 42–51. https://doi.org/10.1016/j.jngse.2018.04.017.
Information & Authors
Information
Published In
International Journal of Geomechanics
Volume 24 • Issue 9 • September 2024
Copyright
© 2024 American Society of Civil Engineers.
History
Received: Aug 5, 2023
Accepted: Apr 17, 2024
Published online: Jun 24, 2024
Published in print: Sep 1, 2024
Discussion open until: Nov 24, 2024
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.