Numerical Analysis of a Jacked-In Pile Installation in Clay
Publication: International Journal of Geomechanics
Volume 23, Issue 6
Abstract
In this paper, a small strain numerical procedure, the press-replace method (PRM), is adopted to model the monotonic, quasi-static installation of a jacked-in pile under an undrained condition. Numerical simulations are carried out using the small-strain geotechnical finite-element software PLAXIS 2D (version 20.03.00.60). The PRM implementation for modeling jacked-in pile installation is described. This paper aims to demonstrate and assess the prediction potential and limitations of the PRM for modeling the pile installation process followed by the subsequent load testing, using published information from two well-known field case studies. It is shown that the combination of the PRM with the modified Cam-clay constitutive model can not only capture the penetration resistance experienced by the pile during jacking but also simulate realistic stress and pore-pressure changes around the pile caused by the jacking process. The pore-pressure response during postinstallation consolidation, which leads to the pile setup phenomenon, can also be reasonably captured. Subsequently, the importance of incorporating installation effects in the numerical simulations of pile load tests is demonstrated, using a wished-in-place (WIP) pile model and another with the installation process simulated via the PRM. The PRM model predicts a significantly higher pile capacity than the WIP model. The different load-settlement behavior of the two piles can be attributed to the different soil states present in the two models at the start of the load test, in which the WIP model does not capture the changes occurring in the stresses, overconsolidation ratios, and void ratios of the surrounding soil caused by the pile jacking process.
Get full access to this article
View all available purchase options and get full access to this article.
References
Andersen, K. H., L. Andresen, H. P. Jostad, and E. C. Clukey. 2004. “Effect of skirt-tip geometry on set-up outside suction anchors in soft clay.” In Proc., 23rd Int. Conf. Offshore Mechanics and Arctic Engineering, 1035–1044. New York: ASME.
Arunmongkol, J. 2004. “Centrifuge modelling of single pile subjected to compression and tension in clay.” M.Eng. thesis, Dept. of Civil and Environmental Engineering, National Univ. of Singapore.
Azzouz, A. S., and M. J. Morrison. 1988. “Field measurements on model pile in two clay deposits.” J. Geotech. Eng. 114 (1): 104–121. https://doi.org/10.1061/(ASCE)0733-9410(1988)114:1(104).
Baligh, M. M. 1985. “Strain path method.” J. Geotech. Eng. 111 (9): 1108–1136. https://doi.org/10.1061/(ASCE)0733-9410(1985)111:9(1108).
Bond, A. J., and R. J. Jardine. 1991. “Effects of installing displacement piles in a high OCR clay.” Géotechnique 41 (3): 341–363. https://doi.org/10.1680/geot.1991.41.3.341.
Bond, A. J., R. J. Jardine, and J. C. P. Dalton. 1991. “Design and performance of the imperial college instrumented pile.” Geotech. Test. J. 14 (4): 413–424. https://doi.org/10.1520/GTJ10210J.
Burgers, J. M., and G. W. Scott Blair. 1949. Report on principles of rheological nomenclature. Amsterdam, Netherlands: North Holland Publishing Co.
Carter, J. P., M. F. Randolph, and C. P. Wroth. 1979. “Stress and pore pressure changes in clay during and after the expansion of a cylindrical cavity.” Int. J. Numer. Anal. Methods Geomech. 3 (4): 305–322. https://doi.org/10.1002/nag.1610030402.
Engin, H. K. 2013. “Modelling pile installation effects—A numerical approach.” Ph.D. thesis, Dept. of Geoscience and Engineering, Delft Univ. of Technology.
Engin, H. K., R. B. J. Brinkgreve, and A. F. van Tol. 2015. “Simplified numerical modelling of pile penetration—The press-replace technique.” Int. J. Numer. Anal. Methods Geomech. 39 (15): 1713–1734. https://doi.org/10.1002/nag.2376.
Hamann, T., G. Qiu, and J. Grabe. 2015. “Application of a coupled Eulerian–Lagrangian approach on pile installation problems under partially drained conditions.” Comput. Geotech. 63: 279–290. https://doi.org/10.1016/j.compgeo.2014.10.006.
Hight, D. W., A. J. Bond, and J. D. Legge. 1992. “Characterization of the Bothkennar clay: An overview.” Géotechnique 42 (2): 303–347. https://doi.org/10.1680/geot.1992.42.2.303.
Khanmohammadi, M., and K. Fakharian. 2019. “Numerical modelling of pile installation and set-up effects on pile shaft capacity.” Int. J. Geotech. Eng. 13 (5): 484–498. https://doi.org/10.1080/19386362.2017.1368185.
Ko, H. Y., R. H. Atkinson, G. G. Globe, and C. D. Ealy. 1984. “Centrifugal modeling of pile foundations.” In Analysis and design of pile foundations, edited by J. R. Meyer, 21–40. New York: ASCE.
Komurka, V. E., A. B. Wagner, and T. B. Edil. 2003. Estimating soil/pile set-up. Final Rep. No. 0092-00-14. Madison, WI: Wisconsin Highway Research Program.
Konkol, J., and L. Balachowski. 2016. “Large deformation finite element analysis of undrained pile installation.” Stud. Geotech. Mech. 38 (1): 45–54. https://doi.org/10.1515/sgem-2016-0005.
Konkol, J., and L. Balachowski. 2017. “Influence of installation effects on pile bearing capacity in cohesive soils-large deformation analysis via finite element method.” Stud. Geotech. Mech. 39 (1): 27–38. https://doi.org/10.1515/sgem-2017-0003.
Konrad, J. M., and M. Roy. 1987. “Bearing capacity of friction piles in marine clay.” Géotechnique 37 (2): 163–175. https://doi.org/10.1680/geot.1987.37.2.163.
La Rochelle, P., B. Trak, F. Tavenas, and M. Roy. 1974. “Failure of a test embankment on a sensitive Champlain clay deposit.” Can. Geotech. J. 11 (1): 142–164. https://doi.org/10.1139/t74-009.
Lehane, B. M. 1992. “Experimental investigations of pile behaviour using instrumented field piles.” Ph.D. thesis, Imperial College of Science, Technology and Medicine, Univ. of London (Imperial College).
Lehane, B. M., and D. R. Gill. 2004. “Displacement fields induced by penetrometer installation in an artificial soil.” Int. J. Phys. Modell. Geotech. 4 (1): 25–36. https://doi.org/10.1680/ijpmg.2004.040103.
Lehane, B. M., and R. J. Jardine. 1994. “Displacement–pile behaviour in a soft marine clay.” Can. Geotech. J. 31 (2): 181–191. https://doi.org/10.1139/t94-024.
Leroueil, S., F. A. Tavenas, F. Brucy, P. La Rochelle, and M. Roy. 1979. “Behavior of destructured natural clays.” J. Geotech. Eng. Div. 105 (6): 759–778. https://doi.org/10.1061/AJGEB6.0000823.
Leroueil, S., and P. R. Vaughan. 1990. “The general and congruent effects of structure in natural soils and weak rocks.” Géotechnique 40 (3): 467–488. https://doi.org/10.1680/geot.1990.40.3.467.
Li, Y., B. M. Lehane, and Q. Liu. 2018. “Centrifuge modelling of jacked pile in clay.” [In Mandarin.] Chin. J. Eng. 40 (3): 285–292.
Lim, Y. X. 2017. “Numerical study of cone penetration test in clays using press-replace method.” Ph.D. thesis, Dept. of Civil and Environmental Engineering, National Univ. of Singapore.
Lim, Y. X., S. A. Tan, and K. K. Phoon. 2018. “Application of press-replace method to simulate undrained cone penetration.” Int. J. Geomech. 18 (7): 04018066. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001186.
Liyanapathirana, D. S. 2008. “A numerical model for predicting pile setup in clay.” In GeoCongress 2008: Characterization, Monitoring, Modeling of Geosystems, Geotechnical Special Publication 179, edited by A. N. Alshawabkeh, K. R. Reddy, and M. V. Khire, 710–717. Reston, VA: ASCE.
Madabhushi, G. 2015. Centrifuge modelling for civil engineers. Boca Raton, FL: CRC Press.
Pucker, T., and J. Grabe. 2012. “Numerical simulation of the installation process of full displacement piles.” Comput. Geotech. 45: 93–106. https://doi.org/10.1016/j.compgeo.2012.05.006.
Randolph, M. F., J. P. Carter, and C. P. Wroth. 1979. “Driven piles in clay: The effects of installation and subsequent consolidation.” Géotechnique 29 (4): 361–393. https://doi.org/10.1680/geot.1979.29.4.361.
Roy, M., R. Blanchet, F. Tavenas, and P. La Rochelle. 1981. “Behaviour of a sensitive clay during pile driving.” Can. Geotech. J. 18 (1): 67–85. https://doi.org/10.1139/t81-007.
Sagaseta, C., and A. J. Whittle. 2001. “Prediction of ground movements due to pile driving in clay.” J. Geotech. Geoenviron. Eng. 127 (1): 55–66. https://doi.org/10.1061/(ASCE)1090-0241(2001)127:1(55).
Schmertmann, J. H. 1991. “The mechanical aging of soils.” J. Geotech. Eng. 117 (9): 1288–1330. https://doi.org/10.1061/(ASCE)0733-9410(1991)117:9(1288).
Sheng, D., K. D. Eigenbrod, and P. Wriggers. 2005. “Finite element analysis of pile installation using large-slip frictional contact.” Comput. Geotech. 32 (1): 17–26. https://doi.org/10.1016/j.compgeo.2004.10.004.
Sheng, D., M. Nazem, and J. P. Carter. 2009. “Some computational aspects for solving deep penetration problems in geomechanics.” Comput. Mech. 44 (4): 549–561. https://doi.org/10.1007/s00466-009-0391-6.
Smith, P. R., R. J. Jardine, and D. W. Hight. 1992. “The yielding of Bothkennar clay.” Géotechnique 42 (2): 257–274. https://doi.org/10.1680/geot.1992.42.2.257.
Tavenas, F., P. Jean, P. Leblond, and S. Leroueil. 1983. “The permeability of natural soft clays. Part II: Permeability characteristics.” Can. Geotech. J. 20 (4): 1098–1118.
Tavenas, F., and S. Leroueil. 1977. “Effects of stresses and time on yielding of clays.” In Proc., 9th Int. Conf. Soil Mech. Found. Eng., 319–326. Tokyo: Japanese Society of Soil Mechanics and Foundation Engineering.
Tavenas, F. A., C. Chapeau, P. La Rochelle, and M. Roy. 1974. “Immediate settlements of three test embankments on Champlain clay.” Can. Geotech. J. 11 (1): 109–141. https://doi.org/10.1139/t74-008.
Teh, C. I., and G. T. Houlsby. 1991. “An analytical study of the cone penetration test in clay.” Géotechnique 41 (1): 17–34. https://doi.org/10.1680/geot.1991.41.1.17.
Tehrani, F. S., P. Nguyen, R. B. J. Brinkgreve, and A. F. van Tol. 2016. “Comparison of press-replace method and material point method for analysis of jacked piles.” Comput. Geotech. 78: 38–53. https://doi.org/10.1016/j.compgeo.2016.04.017.
van Langen, H. 1991. “Numerical analysis of soil–structure interaction.” Ph.D. thesis, Geo-Engineering Section, Delft Univ. of Technology.
Xie, Y., C. F. Leung, and Y. K. Chow. 2017. “Centrifuge modelling of spudcan–pile interaction in soft clay overlying sand.” Géotechnique 67 (1): 69–77. https://doi.org/10.1680/jgeot.15.P.031.
Yeung, A. T., S. K. A. Au, and T. H. Lam. 2012. “Numerical simulation of pressure-controlled cavity expansion process in clay at constant volumetric expansion rate.” Géotechnique 62 (4): 353–357. https://doi.org/10.1680/geot.9.P.106.
Yi, J. T., S. H. Goh, F. H. Lee, and M. F. Randolph. 2012. “A numerical study of cone penetration in fine-grained soils allowing for consolidation effects.” Géotechnique 62 (8): 707–719. https://doi.org/10.1680/geot.8.P.155.
Yu, H. 2000. Cavity expansion methods in geomechanics. Dordrecht, Netherlands: Kluwer.
Zdravković, L., D. M. Potts, and D. W. Hight. 2002. “The effect of strength anisotropy on the behaviour of embankments on soft ground.” Géotechnique 52 (6): 447–457. https://doi.org/10.1680/geot.2002.52.6.447.
Information & Authors
Information
Published In
International Journal of Geomechanics
Volume 23 • Issue 6 • June 2023
Copyright
© 2023 American Society of Civil Engineers.
History
Received: Apr 20, 2022
Accepted: Nov 30, 2022
Published online: Mar 28, 2023
Published in print: Jun 1, 2023
Discussion open until: Aug 28, 2023
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.