Behavior of Monopile Foundations for Offshore Wind Farms in Sand
Publication: Journal of Waterway, Port, Coastal, and Ocean Engineering
Volume 142, Issue 1
Abstract
Most offshore wind-turbine foundations are monopile foundations. Monopile foundations have the advantages of simple structures and are convenient to construct. In recent years, large-diameter monopile foundations, with diameters larger than 4 m, have been used in engineering applications to increase the bearing capacity of wind turbines. Increasing the foundation pile diameter changes the bearing characteristics from those of traditional small-diameter steel-pipe piles. However, research on the bearing characteristics of large-diameter steel-pipe piles is lacking; no mature method exists to estimate the bearing capacity. On the basis of numerical simulations, the differences between the stress and deformation characteristics of the pile body and the soil around it between large-diameter and small-diameter steel-pipe piles subjected to vertical loads and horizontal loads in sand are investigated in this study. A method to calculate the vertical bearing capacity, considering the soil-arching effect, is proposed. In addition, a method to calculate the lateral displacement, based on the shell theory, is proposed. The applicability of the proposed method is verified using laboratory experiments. The result shows that the vertical ultimate bearing capacity calculated by the method considering the soil-arching effect is significantly higher than that predicted by the American Petroleum Institute (API) code method, and the lateral displacement at the pile top using the method based on the shell theory is 5–45% greater than that predicted by the curve method in the API code.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This study was supported by the National Natural Science Foundation of China (51279127), the Excellent Young Scholars of the National Natural Science Foundation of China (51322904), and the Program for New Century Excellent Talents in University (NCET-11-0370).
References
Achmus, M., and Abdel-Rahman, K. (2012). “Design of piles for offshore wind energy foundations with respect to horizontal loading.” Proc., 22nd Int. Ocean and Polar Engineering Conf., ISOPE, Rhodes, Greece, 143–150.
Achmus, M., Abdel-Rahman, K., and Kuo, Y. S. (2007). “Numerical modelling of large diameter steel piles under monotonic and cyclic horizontal loading.” Proc., 10th Int. Symp. on Numerical Models in Geomechanics, Taylor & Francis, Rhodes, Greece, 453–459.
Achmus, M., Abdel-Rahman, K., and Kuo, Y. S. (2008). “Design of monopile foundations for offshore wind energy converters.” Proc., 11th Baltic Sea Geotechnical Conf., International Society for Soil Mechanics and Geotechnical Engineering, Gdansk, Poland, 463–470.
API (American Petroleum Institute). (2000). Recommended practice for planning, designing and constructing fixed offshore platforms, 21st Ed., Washington, DC.
Ashour, M., and Norris, G. (2000). “Modeling lateral soil-pile response based on soil-pile interaction.” J. Geotech. Geoenviron. Eng., 420–428.
Bolton, M. D. (1986). “The strength and dilatancy of sands.” Géotechnique, 36(1), 65–78.
DNV (Det Norske Veritas). (2007). “Design of offshore wind turbine structures.” Offshore Standard DNV-OS-J101, Høvik, Norway.
Doherty, P., and Gavin, K. (2012). “Laterally loaded monopile design for offshore wind farms.” Proc., ICE–Energy, Institution of Civil Engineers, Dublin, Ireland, 7–17.
Flugge, W. (1973). Stresses in shells, Butterworth, London.
Gavin, K. G., and Lehane, B. M. (2003). “The shaft capacity of pipe piles in sand.” Can. Geotech. J., 40(1), 36–45.
Gibson, J. E. (1980). Thin shells computing and theory, Pergamon Press, Oxford, U.K.
Haiderali, A., and Madabhushi, G. (2012). “Three-dimensional finite element modelling of monopiles for offshore wind turbines.” Proc., World Congress on Advances in Civil, Environmental, and Materials Research, ACEM, Seoul, Korea, 3277–3295.
Jardine, R. J., and Chow, F. C. (1996). New design methods for offshore piles, Marine Technology Directorate, Ltd., London.
Jardine, R. J., Chow, F. C., Overy, R., and Standing, J. (2005). ICP design methods for driven piles in sands and clays, Thomas Telford, London.
Kim, B. T., Kim, N. K., Lee, W. J., and Kim, Y. S. (2004). “Experimental load–transfer curves of laterally loaded piles in Nak-Dong river sand.” J. Geotech. Geoenviron. Eng., 416–425.
Kumar, J., and Khatri, V. N. (2008). “Effect of footing width on .” Can. Geotech. J., 45(12), 1673–1684.
Kuo, Y. S., Achmus, M., and Abdel-Rahman, K. (2009). “Estimation of lateral deformation of monopile foundations by use of cyclic triaxial tests.” Chin. J. Geotech. Eng., 31(11), 1729–1734.
Lacasse, S., and Goulois, A. M. (1989). “Uncertainty in API parameters for prediction of axial capacity of driven piles in sand.” Proc., 21st Offshore Technology Conf., OTC, Houston, 353–358.
Lehane, B. M., Schneider, J. A., and Xu, X. (2007). “Development of the UWA-05 design method for open and closed ended driven piles in siliceous sand.” Contemporary Issues in Deep Foundations, Geotechnical special publication 158, W. Camp, R. Castelli, D. F. Laefer, and S. Paikowsky, eds., ASCE, Reston, VA, 1–10.
Lesny, K., Paikowsky, S. G., and Gurbuz, A. (2007). “Scale effects in lateral load response of large diameter monopiles.” Contemporary Issues in Deep Foundations, Geotechnical special publication 158, W. Camp, R. Castelli, D. F. Laefer, and S. Paikowsky, eds., ASCE, Reston, VA, 1–10.
Liu, R., Liu, W. B., Wu, X. L., and Yan, S. W. (2013). “Global lateral buckling analysis of idealized subsea pipelines.” J. Univ., 20(7), 2054–2065.
Liu, R., Yan, S. W., and Li, Z. H. (2009). “Soil plug effect prediction and pile driveability analysis for large-diameter steel piles in ocean engineering.” China Ocean Eng., 23(1), 107–118.
Miller, G. A., and Lutenegger, A. J. (1997). “Influence of pile plugging on skin friction in over consolidated clay.” J. Geotech. Geoenviron. Eng., 525–533.
Paik, K., and Salgado, R. (2003). “Determination of bearing capacity of open-ended piles in sand.” J. Geotech. Geoenviron. Eng., 46–57.
Paikowsky, S. G. (1990). “The mechanism of pile plugging in sand.” Proc., 22nd Offshore Technology Conf., OTC, Houston, 593–604.
Randolph, M. F., and Gourvenec, M. R. S. (2011). Offshore geotechnical engineering, Spon Press, New York.
Randolph, M. F., Leong, E. C., and Houlsby, G. T. (1991). “One-dimensional analysis of soil plugs in pipe piles.” Géotechnique, 41(4), 587–598.
Schneider, J. A., Xu, X. T., and Lehane, B. M. (2008). “Database assessment of CPT-based design methods for axial capacity of driven piles in siliceous sands.” J. Geotech. Geoenviron. Eng., 1227–1244.
Snyder, B., and Kaiser, M. J. (2009). “Ecological and economic cost-benefit analysis of offshore wind energy.” Renewable Energy, 34(6), 1567–1578.
Ventsel, E., and Krauthammer, T. (2001). Thin plates and shells: Theory, analysis and applications, Marcel Dekker, New York.
Vlasov, V. Z. (1964). General theory of shells and its application in engineering, National Aeronautics and Space Administration, Washington, DC.
Wang, G. C., Wang, W., and Yang, M. (2011). “Design and analysis of monopile foundation for 3.6 MW offshore wind turbine.” Chin. J. Geotech. Eng., 33(Suppl 2), 95–100.
Wiedmann, J., Lesny, K., and Richwien, W. (2004). “Evaluation of pile diameter effects on soil-pile stiffness.” Proc., 7th German Wind Energy Conf., Wilhelmshaven, Germany.
Xue, D. W. (1979). “A solution of cylindrical shell under concentrated loads.” Chin. J. Theor. Appl. Mech., 15(1), 92–95.
Zhu, B., Xiong, G., Liu, J. C., Sun, Y. X., and Chen, R. P. (2013). “Centrifuge modelling of a large-diameter single pile under lateral loads in sand.” Chin. J. Geotech. Eng., 35(10), 1807–1815.
Information & Authors
Information
Published In
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Aug 25, 2014
Accepted: Mar 20, 2015
Published online: Jun 24, 2015
Discussion open until: Nov 24, 2015
Published in print: Jan 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.