Operating Speed of Different Classes of Vehicles at Horizontal Curves on Two-Lane Rural Highways
Publication: Journal of Transportation Engineering
Volume 139, Issue 3
Abstract
The majority of operating speed models reported in the literature primarily consider passenger cars and only rarely consider heavy vehicles. No study on the influence of geometry on speeds of other classes of vehicles like buses and two-wheelers, which contribute significantly to the mix of traffic in India, has been reported. This study highlights the need to develop operating speed and speed reduction models for different classes of vehicles and develops models for predicting operating speed at tangent and midcurve sections of horizontal alignment of two-lane rural highways. In addition, models for estimating the speed reduction from tangent to curve are also developed. The independent variable used to predict tangent speed is the length of the preceding tangent. The radius and length of a curve emerged as the most important variables for speed at midcurve. Speed reduction can be estimated from the preceding variables along with the approach tangent speed. The models developed in the study can be used in the design and evaluation of rural highways as well as in establishing speed limits and other enforcement measures.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors sincerely acknowledge the ample support given by the National Institute of Technology, Calicut. Also, the help rendered by Ms. Salma Fathima Saleem, former PG student of NIT, Calicut, during the data collection phase is acknowledged.
References
AASHTO. (2001). A policy on geometric design of highways and streets, 4th Ed., Washington, DC.
Al-Masaeid, H. R., Hamed, M., Aboul-Ela, M., and Ghannam, A. G. (1995). “Consistency of horizontal alignment for different vehicle classes.” Transportation Research Record 1500, Transportation Research Board, Washington, DC, 178–183.
Alexander, G. J., and Lunenfeld, H. (1986). “Driver expectancy in highway design and traffic operations.” FHwA-TO-86-1, Federal Highway Administration, U.S. Dept. of Transportation, Washington DC.
Castro, M., Sanchez, J. F., Sanchez, J. A., and Iglesias, L. (2011). “Operating speed and speed differential for highway design consistency.” J. Transp. Eng., 137(11), 837–840.
Evans, L. (1991). Traffic safety and the driver, Van Nostrand Reinhold, New York.
Fitzpatrick, K. et al. (2000a). Alternative design consistency rating methods for two-lane rural highways, FHWA-RD-99-172, U.S. DOT, Washington, DC.
Fitzpatrick, K. et al. (2000b). Speed prediction for two-lane rural highways FHWA-RD-99-171, U.S. DOT, Washington, DC.
Garber, N. J., and Ehrhart, A. A. (2000). “The effect of speed, flow and geometric characteristics on crash rates for different types of Virginia highways.”, Virginia Transportation Research Council, Charlottesville, VA.
Gibreel, G. M., Easa, S. M., Hassan, Y., and El-Dimeery, I. A. (1999). “State of the art of highway geometric design consistency.” J. Transp. Eng., 125(4), 305–313.
Hassan,Y. et al. (2011). “Modeling operating speed.” Transportation Research Circular, E-C151, Federal Highway Administration, Transportation Research Board, Washington, DC.
Hayward, J. C. (1980). “Highway alignment and superelevation: some design speed misconceptions.” Transportation Research Record 757, Transportation Research Board, Washington, DC, 22–24.
Hines, W. W., Montgomery, D. C., Goldsman, D. M., and Borror, C. M. (2003). Probability and statistics in engineering, Wiley, Singapore, 321–330.
Hirsh, M. (1987). “Probabilistic approach to consistency of highway alignment.” J. Transp. Eng., 113(3), 268–276.
Ibrahim, S. El.-B., and Sayed, T. (2011). “Developing safety performance functions incorporating reliability-based risk measures.” Accid. Anal. Prev., 43(6), 2153–2159.
Koeppel, G., and Bock, H. (1979). “Operating speed as a function of curvature change rate.” Research Road Construction and Road Traffic Technique (Forschung Strassenbau und Strassenverkehrstechnik), Minister of Transportation, Bonn, Germany.
Krammes, R. A. (1997). “Interactive highway safety design model: Design consistency module.” Public Rd., 61(2), 47–52.
Lamm, R. (1973). “Driving dynamics and design characteristics: a contribution for highway design under special consideration of operating speeds.” Thesis for Appointment as University Lecturer. Publications of the Institute for Highway and Railroad Engineering, Vol. 11, Univ. of Karlsruhe (Technische Hochschule), Germany.
Lamm, R., Choueiri, E. M., Hayward, J. C., and Paluri, A. (1988). “Possible design procedures to promote design consistency in highway geometric design of two-lane rural roads.” Transportation Research Record 1195, Transportation Research Board, Washington, DC, 111–122.
Lamm, R., Hayward, J., and Cargin, J. (1986). “Comparison of different procedure for evaluating speed consistency.” Transportation Research Record 1100, Transportation Research Board, Washington, DC.
McFadden, J., and Elefteriadou, L. (2000). “Evaluating horizontal alignment design consistency of two-lane rural highways: Development of new procedure.” Transportation Research Record 1737, Transportation Research Board, Washington, DC, 9–17.
Misaghi, P., and Hassan, Y. (2005). “Modeling operating speed and speed differential on two-lane rural roads.” J. Transp. Eng., 131(6), 408–417.
Nicholson, A. (1998). “Superelevation, side friction, and roadway consistency.” J. Transp. Eng., 124(5), 411–418.
Otteson, L. J., and Krammes, R. A. (2000). “Speed profile model for a design consistency evaluation procedure in the united states.” Transportation Research Record 1701, National Research Council, Washington, DC, Paper No. 00-3259.
Park, Y. J., and Saccomanno, F. F. (2006). “Evaluating speed consistency between successive elements of a two-lane rural highway.” Transp. Res. A Policy Pract., 40(5), 375–385.
Poe, C. M., Tarris, J. P., and Mason, J. M. Jr. (1996). Relationship of operating speed to roadway geometric design speed, FHWA-RD-96-024, Federal Highway of Administration, U.S. DOT, Washington, DC.
Polus, A., Fitzpatrick, K., and Fambro, D. B. (2000). “Predicting operating speeds on tangent sections of two-lane rural highways.” Transportation Research Record 1737, Transportation Research Board, Washington, DC, 50–57.
Wooldridge, M. D., Fitzpatrick, K., Harwood, D. W., Potts, I. B., Elefteriadou, L., and Torbic, D. J. (2003). Geometric design consistency on high speed rural two-lane roadways, Rep. 502, National Corporative Highway Research Program, Transportation Research Board, Washington, DC.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Apr 3, 2012
Accepted: Sep 17, 2012
Published online: Sep 19, 2012
Published in print: Mar 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.