Structural Integrity of Bolted Glulam Frame Connections Reinforced with Self-Tapping Screws in a Column Removal Scenario
Publication: Journal of Structural Engineering
Volume 146, Issue 10
Abstract
An experimental study has been carried out to investigate the behavior of glulam beam-to-column bolted connections subjected to monotonic loading in a column removal scenario. Eight test groups, each including four replicates of a wood-steel-wood glulam bolted connection configuration, were experimentally examined. The connections in four test groups were reinforced perpendicular to wood grain with self-tapping screws (STS). Test results showed that in the event of a column removal, the connections behaved as semirigid connections with considerable moment-resisting capacity, unlike typical beam-to-column timber connections that are assumed to be perfectly pinned. Experimental results also revealed that increasing the number of bolt rows from two to three rows, with each row having two bolts, increased the moment-carrying capacity of both unreinforced and reinforced connections with increments greater than those obtained by increasing the bolt end distance from four to five times the bolt diameter. Most importantly, STS-reinforced glulam connections manifested considerably increased moment-carrying capacities compared to the respective unreinforced connections by a factor ranging between 1.30 and 2.4. This has proven the ability of such glulam frame connections to redistribute the applied load and successfully transfer it to adjacent structural elements in case of column removal that could be caused by fire, explosion, or accidental damage.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
Acknowledgments
This research project was funded using a NSERC-Discovery Grant awarded to the second author, as well as a partial in-kind contribution provided by Nordic Structures Inc. Any opinions, findings, conclusions, or recommendations are those of the authors and do not necessarily reflect the views of the sponsoring parties. The authors would like to thank B. Vasconcelos, C. Tomiuck, C. Hubbard, I. Grant, N. Lepoudre, and J. Kruse for their assistance in preparing a few of the test specimens and in conducting a number of this research project’s experiments. Special thanks go to Dr. M. Leitch from the Faculty of Natural Resources Management at Lakehead University for his kind assistance in preparing the slotted cuts in all glulam beam sections tested in this project using his portable band-saw mill, and to Conrad Hagstrom and Rob Timoon for their help in the Dept. of Civil Engineering’s Structures Laboratory.
References
Andreolli, M., M. Piazza, R. Tomasi, and R. Zandonini. 2011. “Ductile moment-resistant steel-timber connections.” Proc. Inst. Civ. Eng. Struct. Build. 164 (2): 65–78. https://doi.org/10.1680/stbu.9.00098.
ASTM. 2019. Standard specification for high strength structural bolts and assemblies. West Conshohocken, PA: ASTM.
Blaß, H. J., and P. Schädle. 2011. “Ductility aspects of reinforced and non-reinforced timber joints.” Eng. Struct. 33 (11): 3018–3026. https://doi.org/10.1016/j.engstruct.2011.02.001.
CCMC (Canadian Construction Materials Centre). 2014a. Evaluation report: Nordic Lam. Ottawa: CCMC.
CCMC (Canadian Construction Materials Centre). 2014b. Evaluation report: SWG ASSY VG Plus and SWG ASSY 3.0 self-tapping wood screws. Ottawa: CCMC.
CSA (Canadian Standard Association). 2013. General requirements for rolled or welded structural quality steel/structural quality steel. Rexdale, ON: CSA.
CSA (Canadian Standard Association). 2014. Engineering design in wood. Rexdale, ON: CSA.
CSA (Canadian Standard Association). 2016. Structural glued-laminated timber. CSA O122. Rexdale, ON: CSA.
Gattesco, N., and I. Toffolo. 2004. “Experimental study on multiple-bolt steel-to-timber tension joints.” Mater. Struct. 37 (2): 129–138. https://doi.org/10.1007/BF02486609.
Gehloff, M., M. Closen, and F. Lam. 2010. “Reduced edge distances in bolted timber moment connections with perpendicular to grain reinforcements.” In Proc., 11th World Conf. on Timber Engineering. Sesto Fiorentino, Italy: Trees and Timber Institute, National Research Council of Italy.
Hampson, J. A., H. G. Prion, and F. Lam. 2003. “The effect of end distance on the moment resistance of timber rivet connections.” Can. J. Civ. Eng. 30 (5): 945–948. https://doi.org/10.1139/l03-050.
Huber, J. A., M. Ekevad, U. A. Girhammar, and S. Berg. 2019. “Structural robustness and timber buildings—A review.” Wood Mater. Sci. Eng. 14 (2): 107–128. https://doi.org/10.1080/17480272.2018.1446052.
Lam, F., M. Schulte-Wrede, C. C. Yao, and J. J. Gu. 2008. “Moment resistance of bolted timber connections with perpendicular to grain reinforcements.” In Proc., 10th World Conf. of Timber Engineering. Madison, WI: Engineered Wood Products Association.
Lathuillière, D., L. Bléron, T. Descamps, and J. F. Bocquet. 2015. “Reinforcement of dowel type connections.” Constr. Build. Mater. 97 (Oct): 48–54. https://doi.org/10.1016/j.conbuildmat.2015.05.088.
Mohammad, M., and J. H. Quenneville. 2001. “Bolted wood-steel and wood-steel-wood connections: Verification of a new design approach.” Can. J. Civ. Eng. 28 (2): 254–263. https://doi.org/10.1139/l00-105.
Mpidi Bita H., N. Currie, and T. Tannert. 2016. “Assessment of disproportionate collapse for multi-storey cross-laminated timber buildings.” In Proc., 14th World Conf. on Timber Engineering. Vienna, Austria: Vienna Univ. of Technology.
Mpidi Bita, H., and T. Tannert. 2017. “Robustness of multi-storey timber buildings.” In Proc., 39th Int. Symp. on Bridge and Structural Engineering, 1926–1933. Zürich, Switzerland: International Symposium on Bridge and Structural Engineering.
Muñoz, W., M. Mohammad, A. Salenikovich, and P. Quenneville. 2008. Determination of yield point and ductility of timber assemblies: In search for a harmonized approach. Tacoma, WA: Engineered Wood Products Association.
Murty, B., A. Asiz, and I. Smith. 2008. “Wood and engineered wood product connections using small steel tube fasteners: An experimental study.” J. Inst. Wood Sci. 18 (2): 59–67. https://doi.org/10.1179/wsc.2008.18.2.59.
National Research Council of Canada. 2015. National building code of Canada (NBCC). Ottawa, ON: Institute for Research in Construction.
Song, X., Y. Jiang, X. Gu, and Y. Wu. 2017. “Load-carrying capacity of lengthwise cracked wood beams retrofitted by self-tapping screws.” J. Struct. Eng. 143 (6): 04017021. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001742.
Nordic Structures. 2015. Design properties of Nordic lam. Montréal: Nordic Structures.
Wang, M., X. Song, X. Gu, Y. Zhang, and L. Luo. 2014. “Rotational behavior of bolted beam-to-column connections with locally cross-laminated glulam.” J. Struct. Eng. 141 (4): 04014121. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001035.
Xiong, H., and Y. Liu. 2016. “Experimental study of the lateral resistance of bolted glulam timber post and beam structural systems.” J. Struct. Eng. 142 (4): E4014002. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001205.
Xiong, H., Y. Liu, Y. Yao, and B. Li. 2017. “Experimental study on the lateral resistance of reinforced glued-laminated timber post and beam structures.” J. Asian Archit. Build. Eng. 16 (2): 379–385. https://doi.org/10.3130/jaabe.16.379.
Xu, B. H., A. Bouchaïr, and P. Racher. 2015. “Mechanical behavior and modeling of dowelled steel-to-timber moment-resisting connections.” J. Struct. Eng. 141 (6): 04014165. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001119.
Yasumura, M., and N. Kawai. 1998. “Estimating seismic performance of wood-framed structures.” In Proc., 5th WCTE, 564–571. Zürich, Switzerland: Presses Polytechniques et Universitaires Romandes.
Zarnani P., and P. Quenneville. 2014. “Design method for coupled-splice timber moment connections.” In Proc., 13th World Conf. on Timber Engineering. New York: Curran Associates, Inc.
Information & Authors
Information
Published In
Copyright
© 2020 American Society of Civil Engineers.
History
Received: Sep 3, 2019
Accepted: May 5, 2020
Published online: Jul 27, 2020
Published in print: Oct 1, 2020
Discussion open until: Dec 27, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.