Behavior, Failure, and Direct Strength Method Design of Steel Angle Columns: Geometrical Simplicity versus Structural Complexity
Publication: Journal of Structural Engineering
Volume 146, Issue 11
Abstract
This work provides a state-of-the-art report on the current knowledge concerning the structural behavior and design, by means of the Direct Strength Method (DSM), of steel equal-leg angle columns with short-to-intermediate lengths, that is, those buckling in flexural–torsional modes – although cold-formed columns constitute the main focus of the paper, hot-rolled columns are also addressed. The columns dealt with are either fixed-ended or simply supported – the latter designation includes columns with both cylindrically and spherically-hinged end cross-sections. Initially, numerical results concerning the mechanics underlying the buckling and postbuckling behavior of the previous angle columns are presented and discussed: (1) highlighting the main differences between the fixed-ended and simply supported column responses, and (2) evidencing the need for specific design procedures. Next, the paper collects the experimental and numerical failure load data available in the literature, reported by various researchers and dealing with cold-formed and hot-rolled fixed-ended and simply supported columns with several geometries (cross-section dimensions and lengths). Then, the paper presents the mechanical reasoning behind a recently proposed novel DSM-based design approach, as well as the main steps involved in developing and calibrating the corresponding strength curves. Finally, the merits of this design approach are assessed through (1) the estimation quality of the available failure load data, and (2) the evaluation of the associated Load and Resistance Factor Design (LRFD) resistance factors, which are compared with those currently recommended by the North American Design Specifications. The paper closes with an overview of the findings reported and a reference to future developments of this research effort.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request. The data concern the experimental and numerical failure loads used to assess the merits of the DSM-based design approaches proposed in the paper. The models concern the ABAQUS and ANSYS shell finite-element simulations carried out to obtain the numerical results presented and discussed in the paper.
References
Adluri, S. M. R., and M. K. S. Madugula. 1996. “Flexural buckling of steel angles: Experimental investigation.” J. Struct. Eng. 122 (3): 309–317. https://doi.org/10.1061/(ASCE)0733-9445(1996)122:3(309).
AISC. 2000. Load and resistance factor design specification for structural steel buildings and associated commentary. Chicago: AISC.
AISC. 2016. Specification for structural steel buildings and associated commentary. ANSI/AISI-360. Chicago: AISC.
AISI (American Iron and Steel Institute). 2016. North American specification (NAS) for the design of cold-formed steel structural members. AISI-S100. Washington, DC: AISI.
ArcelorMittal. 2015. “ArcelorMittal sections.” Accessed September 10, 2019. http://www.arcelormittal.com/sections/en.
Ban, H. Y., G. Shi, Y. J. Shi, and Y. Q. Wang. 2012. “Residual stress tests of high-strength steel equal angles.” J. Struct. Eng. 138 (12): 1446–1454. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000585.
Ban, H. Y., G. Shi, Y. J. Shi, and Y. Q. Wang. 2013. “Column buckling tests of 420 MPa high strength steel single equal angles.” Int. J. Struct. Stab. Dyn. 13 (2): 1250069. https://doi.org/10.1142/S0219455412500691.
Bebiano, R., D. Camotim, and R. Gonçalves. 2018. “GBTul 2.0—A second-generation code for the GBT-based buckling and vibration analysis of thin-walled members.” Thin Walled Struct. 124 (Mar): 235–257. https://doi.org/10.1016/j.tws.2017.12.002.
Camotim, D., P. B. Dinis, and A. Landesmann. 2016a. “Rational direct strength method design of angle columns: A novel solution for an old problem.” In USB Key Drive Proc., 8th Int. Conf. on Steel and Aluminium Structures (ICSAS 2016), paper 2, edited by B. Young and Y. Cai. Hong Kong: Univ. of Hong Kong.
Camotim, D., P. B. Dinis, and A. D. Martins. 2016b. “Direct strength method (DSM)—A general approach for the design of cold-formed steel structures.” In Recent trends in cold-formed steel construction, edited by C. Yu, 69–105. Amsterdam, Netherlands: Woodhead Publishing.
CEN (Comité Européen de Normalisation). 2005. Eurocode 3: Design of steel structures—Part 1-1: General rules and rules for buildings. Brussels, Belgium: CEN.
Chodraui, G. M. B., Y. Shifferaw, M. Malite, and B. W. Schafer. 2006. “Cold-formed steel angles under axial compression.” In Proc., 18th Int. Specialty Conf. on Cold-Formed Steel Structures, edited by R. LaBoube and W. W. Yu, 285–300. Rolla, MO: Univ. of Missouri-Rolla.
Dinis, P. B., and D. Camotim. 2011. “Buckling, post-buckling and strength of equal-leg angle and cruciform columns: Similarities and differences.” In Vol. A of Proc., 6th European Conf. on Steel and Composite Structures (EUROSTEEL 2011), edited by L. Dunai, et al., 105–110. Brussels, Belgium: European Convention for Constructional Steelwork.
Dinis, P. B., and D. Camotim. 2015. “A novel DSM-based approach for the rational design of fixed-ended and pin-ended short-to-intermediate thin-walled angle columns.” Thin Walled Struct. 87 (Feb): 158–182. https://doi.org/10.1016/j.tws.2014.10.013.
Dinis, P. B., and D. Camotim. 2016a. “Behavior and design of hot-rolled steel pin-ended short-to-intermediate angle columns.” In USB Key Drive Proc., 7th Int. Conf. on Coupled Instabilities in Metal Structures (CIMS 2016), paper 23. Baltimore: Johns Hopkins Univ.
Dinis, P. B., and D. Camotim. 2016b. “Proposal for the codification of a DSM design approach for cold-formed steel short-to-intermediate angle columns.” In Proc., Wei-Wen Yu Int. Specialty Conf. on Recent Research and Developments in Cold-Formed Steel Structures, edited by R. LaBoube and W.-W. Yu, 155–171. Rolla, MO: Missouri Univ. of Science and Technology.
Dinis, P. B., and D. Camotim. 2017. “Spherically-hinged short-to-intermediate angle columns: Stability, non-linear behavior and DSM design.” In Proc., Structural Stability Research Council Annual Stability Conf., paper 11. Chicago: AISC Education Archives.
Dinis, P. B., and D. Camotim. 2019. “Proposal to improve the DSM design of cold-formed steel angle columns: Need, background, quality assessment and illustration.” J. Struct. Eng. 145 (3): 04019071. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002342.
Dinis, P. B., D. Camotim, and A. Landesmann. 2019. “Design of simply supported hot-rolled steel short-to-intermediate angle columns—Design approach based on the direct strength method (DSM).” Steel Constr. Des. Res. 12 (4): 278–290. https://doi.org/10.1002/stco.201900029.
Dinis, P. B., D. Camotim, and V. Preto. 2016. “Behaviour and design of short-to-intermediate hot-rolled steel angle columns.” In Proc., Int. Colloquim on Stability and Ductility of Steel Stuctures 2016 (SDSS 2016), edited by D. Dubina and V. Ungureanu, 477–484. New York: Wiley.
Dinis, P. B., D. Camotim, and N. Silvestre. 2010. “On the local and global buckling behaviour of angle, T-section and cruciform thin-walled members.” Thin Walled Struct. 48 (10–11): 786–797. https://doi.org/10.1016/j.tws.2010.04.012.
Dinis, P. B., D. Camotim, and N. Silvestre. 2012. “On the mechanics of angle column instability.” Thin Walled Struct. 52 (Mar): 80–89. https://doi.org/10.1016/j.tws.2011.12.007.
Dinis, P. B., K. G. Santana, A. Landesmann, and D. Camotim. 2020. “Numerical and experimental study on CFS spherically-hinged equal-leg angle columns: Stability, strength and DSM design.” Thin Walled Struct. https://doi.org/10.1016/j.tws.2020.106862.
ECCS (European Convention for Constructional Steelwork). 1976. Manual on stability of steel structures. Brussels, Belgium: ECCS.
Ellingwood, B., and T. V. Galambos. 1982. “Probability-based criteria for structural design.” Struct. Saf. 1 (1): 15–26. https://doi.org/10.1016/0167-4730(82)90012-1.
Ellobody, E., and B. Young. 2005. “Behavior of cold-formed steel plain angle columns.” J. Struct. Eng. 131 (3): 457–466. https://doi.org/10.1061/(ASCE)0733-9445(2005)131:3(457).
Fan, J. K. 2009. “Theoretical and experimental study on Q460 single equal-leg angles under axial compression.” Master thesis, School of Civil Engineering, Xian Univ. of Architecture and Technology.
Galambos, T. V., and M. K. Ravindra. 1978. “Properties of steel for use in LRFD.” J. Struct. Div. 104 (9): 1459–1468.
Ganesan, K., and C. D. Moen. 2012. “LRFD resistance factor for cold-formed steel compression members.” J. Constr. Steel Res. 72 (May): 261–266. https://doi.org/10.1016/j.jcsr.2012.01.003.
Kennedy, J. B., and M. K. S. Murty. 1972. “Buckling of steel angle and tee struts.” J. Struct. Div. 98 (11): 2507–2522.
Kitipornchai, S., F. G. A. Albermani, and S. L. Chan. 1990. “Elastoplastic finite-element models for angle steel frames.” J. Struct. Eng. 116 (10): 2567–2581. https://doi.org/10.1061/(ASCE)0733-9445(1990)116:10(2567).
Kitipornchai, S., and S. L. Chan. 1987. “Nonlinear finite-element analysis of angle and tee beam-columns.” J. Struct. Eng. 113 (4): 721–739. https://doi.org/10.1061/(ASCE)0733-9445(1987)113:4(721).
Kitipornchai, S., and H. W. Lee. 1986. “Inelastic experiments on angle and tee struts.” J. Constr. Steel Res. 6 (3): 219–236. https://doi.org/10.1016/0143-974X(86)90035-0.
Landesmann, A., D. Camotim, P. B. Dinis, and R. Cruz. 2016. “Short-to-intermediate slender pin-ended cold-formed steel equal-leg angle columns: Experimental investigation, numerical simulation and DSM design.” Eng. Struct. 132 (Feb): 471–493. https://doi.org/10.1016/j.engstruct.2016.11.034.
Liang, Y., V. V. K. Jeyapragasam, L. Zhang, and O. Zhao. 2019. “Flexural–torsional buckling behaviour of fixed-ended hot-rolled austenitic stainless steel equal-leg angle section columns.” J. Constr. Steel Res. 154 (Mar): 43–54. https://doi.org/10.1016/j.jcsr.2018.11.019.
Maia, W. F., J. M. Neto, and M. Malite. 2008. “Stability of cold-formed steel simple and lipped angles under compression.” In Proc., 19th Int. Specialty Conf. on Cold-Formed Steel Structures, edited by R. LaBoube and W. W. Yu, 111–125. Rolla, MO: Univ. of Missouri-Rolla.
Meimand, V. Z., and B. W. Schafer. 2014. “Impact of load combinations on structural reliability determined from testing cold-formed steel components.” Struct. Saf. 48 (May): 25–32. https://doi.org/10.1016/j.strusafe.2013.10.006.
Mesacasa, E., Jr. 2012. “Structural behavior and design of cold-formed steel angle columns.” [In Portuguese.] MASc thesis, Structural Engineering, School of Engineering at São Carlos, Univ. of São Paulo.
Mesacasa, E., Jr., P. B. Dinis, D. Camotim, and M. Malite. 2014. “Mode interaction and imperfection-sensitivity in thin-walled equal-leg angle columns.” Thin Walled Struct. 81 (Aug): 138–149. https://doi.org/10.1016/j.tws.2013.06.021.
Može, P., L.-C. Cajot, F. Sinur, K. Rejec, and D. Beg. 2014. “Residual stress distribution of large steel equal leg angles.” Eng. Struct. 71 (Jul): 35–47. https://doi.org/10.1016/j.engstruct.2014.03.040.
Popovic, D., G. J. Hancock, and K. J. R. Rasmussen. 1999. “Axial compression tests of cold-formed angles.” J. Struct. Eng. 125 (5): 515–523. https://doi.org/10.1061/(ASCE)0733-9445(1999)125:5(515).
Rasmussen, K. J. R. 2005. “Design of angle columns with locally unstable legs.” J. Struct. Eng. 131 (10): 1553–1560. https://doi.org/10.1061/(ASCE)0733-9445(2005)131:10(1553).
Rasmussen, K. J. R. 2006. “Design of slender angle section beam-columns by the direct strength method.” J. Struct. Eng. 132 (2): 204–211. https://doi.org/10.1061/(ASCE)0733-9445(2006)132:2(204).
Ravindra, M. K., and T. V. Galambos. 1978. “Load and resistance factor design for steel.” J. Struct. Div. 104 (9): 1337–1353.
Schafer, B. W. 2019. “Advances in the direct strength method of cold-formed steel design.” Thin Walled Struct. 140 (Jul): 533–541. https://doi.org/10.1016/j.tws.2019.03.001.
Shi, G., Z. Liu, and K. F. Chung. 2009. “Numerical study on the local buckling of 420 MPa steel equal angle columns under axial compression.” In Vol. I of Proc., of 6th Int. Conf. on Advances in Steel Structures (ICASS’09), edited by S. L. Chan, 387–394. Hong Kong: Hong Kong Institute of Steel Construction.
Shifferaw, Y., and B. W. Schafer. 2014. “Cold-formed steel lipped and plain angle columns with fixed ends.” Thin Walled Struct. 80 (Jul): 142–152. https://doi.org/10.1016/j.tws.2014.03.001.
Silvestre, N., P. B. Dinis, and D. Camotim. 2013. “Developments on the design of cold-formed steel angles.” J. Struct. Eng. 139 (5): 680–694. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000670.
Stowell, E. Z. 1951. Compressive strength of flanges.. Washington, DC: National Advisory Committee for Aeronautics (NACA).
Wakabayashi, M., and T. Nonaka. 1965. “On the buckling strength of angles in transmission towers.” Bull. Disaster Prev. Res. Inst. 15 (2): 1–18.
Wang, F., O. Zhao, and B. Young. 2020. “Testing and numerical modelling of S960 ultra-high strength steel angle and channel section stub columns.” Eng. Struct. 204 (Feb): 109902. https://doi.org/10.1016/j.engstruct.2019.109902.
Wilhoite, G. M., R. Zandonini, and A. Zavelani. 1984. “Behaviour and strength of angles in compression: An experimental investigation.” In Proc., ASCE Annual Convention and Structures Congress. Reston, VA: ASCE.
Young, B. 2004. “Tests and design of fixed-ended cold-formed steel plain angle columns.” J. Struct. Eng. 130 (12): 1931–1940. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:12(1931).
Young, B., and K. J. R. Rasmussen. 1999. “Shift of effective centroid in channel columns.” J. Struct. Eng. 125 (5): 524–531. https://doi.org/10.1061/(ASCE)0733-9445(1999)125:5(524).
Zhang, L., K. H. Tan, and O. Zhao. 2019a. “Experimental and numerical studies of fixed-ended cold-formed stainless steel equal-leg angle section columns.” Eng. Struct. 184 (Apr): 134–144. https://doi.org/10.1016/j.engstruct.2019.01.083.
Zhang, L., F. Wang, Y. Liang, and O. Zhao. 2019b. “Press-braked S690 high strength steel equal-leg angle and plain channel section stub columns: Testing, numerical simulation and design.” Eng. Struct. 201 (Dec): 109764. https://doi.org/10.1016/j.engstruct.2019.109764.
Ziemian, R. ed. 2010. Guide to stability design criteria for metal structures. 6th ed. Hoboken, NJ: Wiley.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 146 • Issue 11 • November 2020
Copyright
©2020 American Society of Civil Engineers.
History
Received: Nov 12, 2019
Accepted: Mar 11, 2020
Published online: Aug 18, 2020
Published in print: Nov 1, 2020
Discussion open until: Jan 18, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.